kevin/lora_meshtastic_project
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Signed-off-by: 吴文峰 <kevin@lmve.net>

Browse Source
This commit is contained in:
kevin
2026-03-03 22:16:00 +08:00
parent 7ae6e9e999
commit 88d56e1e9e
1660 changed files with 281430 additions and 0 deletions
Download Patch File Download Diff File Expand all files Collapse all files
code/firmware/variants/esp32s3/CDEBYTE_EoRa-Hub/pins_arduino.h
+28
View File
@@ -0,0 +1,28 @@
// Need this file for ESP32-S3
// No need to modify this file, changes to pins imported from variant.h
// Most is similar to https://github.com/espressif/arduino-esp32/blob/master/variants/esp32s3/pins_arduino.h
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#include <variant.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// Serial
static const uint8_t TX = UART_TX;
static const uint8_t RX = UART_RX;
// Default SPI will be mapped to Radio
static const uint8_t SS = LORA_CS;
static const uint8_t SCK = LORA_SCK;
static const uint8_t MOSI = LORA_MOSI;
static const uint8_t MISO = LORA_MISO;
// The default Wire will be mapped to PMU and RTC
static const uint8_t SCL = I2C_SCL;
static const uint8_t SDA = I2C_SDA;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/CDEBYTE_EoRa-Hub/platformio.ini
+8
View File
@@ -0,0 +1,8 @@
[env:CDEBYTE_EoRa-Hub]
extends = esp32s3_base
board = CDEBYTE_EoRa-Hub
board_level = extra
build_flags =
${esp32s3_base.build_flags}
-D PRIVATE_HW
-I variants/esp32s3/CDEBYTE_EoRa-Hub
code/firmware/variants/esp32s3/CDEBYTE_EoRa-Hub/rfswitch.h
+20
View File
@@ -0,0 +1,20 @@
#include "RadioLib.h"
// This is rewritten to match the requirements of the E80-900M2213S
// The E80 does not conform to the reference Semtech switches(!) and therefore needs a custom matrix.
// See footnote #3 in "https://www.cdebyte.com/products/E80-900M2213S/2#Pin"
// RF Switch Matrix SubG RFO_HP_LF / RFO_LP_LF / RFI_[NP]_LF0
// DIO5 -> RFSW0_V1
// DIO6 -> RFSW1_V2
// DIO7 -> not connected on E80 module - note that GNSS and Wifi scanning are not possible.
static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_LR11X0_DIO7, RADIOLIB_NC,
RADIOLIB_NC};
static const Module::RfSwitchMode_t rfswitch_table[] = {
// mode DIO5 DIO6 DIO7
{LR11x0::MODE_STBY, {LOW, LOW, LOW}}, {LR11x0::MODE_RX, {LOW, HIGH, LOW}},
{LR11x0::MODE_TX, {HIGH, HIGH, LOW}}, {LR11x0::MODE_TX_HP, {HIGH, LOW, LOW}},
{LR11x0::MODE_TX_HF, {LOW, LOW, LOW}}, {LR11x0::MODE_GNSS, {LOW, LOW, HIGH}},
{LR11x0::MODE_WIFI, {LOW, LOW, LOW}}, END_OF_MODE_TABLE,
};
code/firmware/variants/esp32s3/CDEBYTE_EoRa-Hub/variant.h
+50
View File
@@ -0,0 +1,50 @@
// EByte EoRA-Hub
// Uses E80 (LR1121) LoRa module
#define LED_POWER 35
// Button - user interface
#define BUTTON_PIN 0 // BOOT button
#define BATTERY_PIN 1
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_MULTIPLIER 103.0 // Calibrated value
#define ADC_ATTENUATION ADC_ATTEN_DB_0
#define ADC_CTRL 37
#define ADC_CTRL_ENABLED LOW
// Display - OLED connected via I2C by the default hardware configuration
#define HAS_SCREEN 1
#define USE_SSD1306
#define I2C_SCL 17
#define I2C_SDA 18
// UART - The 1mm JST SH connector closest to the USB-C port
#define UART_TX 43
#define UART_RX 44
// Peripheral I2C - The 1mm JST SH connector furthest from the USB-C port which follows Adafruit connection standard. There are no
// pull-up resistors on these lines, the downstream device needs to include them. TODO: test, currently untested
#define I2C_SCL1 21
#define I2C_SDA1 10
// Radio
#define USE_LR1121
#define LORA_SCK 9
#define LORA_MOSI 10
#define LORA_MISO 11
#define LORA_RESET 12
#define LORA_CS 8
#define LORA_DIO9 13
// LR1121
#define LR1121_IRQ_PIN 14
#define LR1121_NRESET_PIN LORA_RESET
#define LR1121_BUSY_PIN LORA_DIO9
#define LR1121_SPI_NSS_PIN LORA_CS
#define LR1121_SPI_SCK_PIN LORA_SCK
#define LR1121_SPI_MOSI_PIN LORA_MOSI
#define LR1121_SPI_MISO_PIN LORA_MISO
#define LR11X0_DIO3_TCXO_VOLTAGE 1.8
#define LR11X0_DIO_AS_RF_SWITCH
code/firmware/variants/esp32s3/CDEBYTE_EoRa-S3/pins_arduino.h
+28
View File
@@ -0,0 +1,28 @@
// Need this file for ESP32-S3
// No need to modify this file, changes to pins imported from variant.h
// Most is similar to https://github.com/espressif/arduino-esp32/blob/master/variants/esp32s3/pins_arduino.h
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#include <variant.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// Serial
static const uint8_t TX = UART_TX;
static const uint8_t RX = UART_RX;
// Default SPI will be mapped to Radio
static const uint8_t SS = LORA_CS;
static const uint8_t SCK = LORA_SCK;
static const uint8_t MOSI = LORA_MOSI;
static const uint8_t MISO = LORA_MISO;
// The default Wire will be mapped to PMU and RTC
static const uint8_t SCL = I2C_SCL;
static const uint8_t SDA = I2C_SDA;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/CDEBYTE_EoRa-S3/platformio.ini
+16
View File
@@ -0,0 +1,16 @@
[env:CDEBYTE_EoRa-S3]
custom_meshtastic_hw_model = 61
custom_meshtastic_hw_model_slug = CDEBYTE_EORA_S3
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 3
custom_meshtastic_display_name = EBYTE EoRa-S3
custom_meshtastic_tags = EByte
custom_meshtastic_requires_dfu = true
extends = esp32s3_base
board = CDEBYTE_EoRa-S3
build_flags =
${esp32s3_base.build_flags}
-D CDEBYTE_EORA_S3
-I variants/esp32s3/CDEBYTE_EoRa-S3
code/firmware/variants/esp32s3/CDEBYTE_EoRa-S3/variant.h
+63
View File
@@ -0,0 +1,63 @@
// LED - status indication
#define LED_POWER 37
// Button - user interface
#define BUTTON_PIN 0 // This is the BOOT button, and it has its own pull-up resistor
// SD card - TODO: test, currently untested, copied from T3S3 variant
#define HAS_SDCARD
#define SDCARD_USE_SPI1
// TODO: rename this to make this SD-card specific
#define SPI_CS 13
#define SPI_SCK 14
#define SPI_MOSI 11
#define SPI_MISO 2
// FIXME: there are two other SPI pins that are not defined here
// Compatibility
#define SDCARD_CS SPI_CS
// Battery voltage monitoring - TODO: test, currently untested, copied from T3S3 variant
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_MULTIPLIER \
2.11 // ratio of voltage divider = 2.0 (R10=1M, R13=1M), plus some undervoltage correction - TODO: this was carried over from
// the T3S3, test to see if the undervoltage correction is needed.
// Display - OLED connected via I2C by the default hardware configuration
#define HAS_SCREEN 1
#define USE_SSD1306
#define I2C_SCL 17
#define I2C_SDA 18
// UART - The 1mm JST SH connector closest to the USB-C port
#define UART_TX 43
#define UART_RX 44
// Peripheral I2C - The 1mm JST SH connector furthest from the USB-C port which follows Adafruit connection standard. There are no
// pull-up resistors on these lines, the downstream device needs to include them. TODO: test, currently untested
#define I2C_SCL1 21
#define I2C_SDA1 10
// Radio
#define USE_SX1262 // CDEBYTE EoRa-S3-900TB <- CDEBYTE E22-900MM22S <- Semtech SX1262
#define USE_SX1268 // CDEBYTE EoRa-S3-400TB <- CDEBYTE E22-400MM22S <- Semtech SX1268
#define SX126X_CS 7
#define LORA_SCK 5
#define LORA_MOSI 6
#define LORA_MISO 3
#define SX126X_RESET 8
#define SX126X_BUSY 34
#define SX126X_DIO1 33
#define SX126X_DIO2_AS_RF_SWITCH // All switching is performed with DIO2, it is automatically inverted using circuitry.
// CDEBYTE EoRa-S3 uses an XTAL, thus we do not need DIO3 as TCXO voltage reference. Don't define SX126X_DIO3_TCXO_VOLTAGE for
// simplicity rather than defining it as 0.
#define SX126X_MAX_POWER \
22 // E22-900MM22S and E22-400MM22S have a raw SX1262 or SX1268 respsectively, they are rated to output up and including 22
// dBm out of their SX126x IC.
// Compatibility with old variant.h file structure - FIXME: this should be done in the respective radio interface modules to clean
// up all variants.
#define LORA_CS SX126X_CS
#define LORA_DIO1 SX126X_DIO1
code/firmware/variants/esp32s3/EBYTE_ESP32-S3/pins_arduino.h
+28
View File
@@ -0,0 +1,28 @@
// Need this file for ESP32-S3
// No need to modify this file, changes to pins imported from variant.h
// Most is similar to https://github.com/espressif/arduino-esp32/blob/master/variants/esp32s3/pins_arduino.h
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#include <variant.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// Serial
static const uint8_t TX = UART_TX;
static const uint8_t RX = UART_RX;
// Default SPI will be mapped to Radio
static const uint8_t SS = LORA_CS;
static const uint8_t SCK = LORA_SCK;
static const uint8_t MOSI = LORA_MOSI;
static const uint8_t MISO = LORA_MISO;
// The default Wire will be mapped to PMU and RTC
static const uint8_t SCL = I2C_SCL;
static const uint8_t SDA = I2C_SDA;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/EBYTE_ESP32-S3/platformio.ini
+9
View File
@@ -0,0 +1,9 @@
[env:EBYTE_ESP32-S3]
extends = esp32s3_base
; board assumes the lowest spec WROOM module: 4 MB (Quad SPI) Flash, No PSRAM
board = ESP32-S3-WROOM-1-N4
board_level = extra
build_flags =
${esp32s3_base.build_flags}
-D EBYTE_ESP32_S3
-I variants/esp32s3/EBYTE_ESP32-S3
code/firmware/variants/esp32s3/EBYTE_ESP32-S3/variant.h
+193
View File
@@ -0,0 +1,193 @@
// Supporting information: https://github.com/S5NC/EBYTE_ESP32-S3/
// Originally developed for E22-900M30S with ESP32-S3-WROOM-1-N4
// NOTE: Uses ESP32-S3-WROOM-1-N4.json in boards folder (via platformio.ini board field), assumes 4 MB (quad SPI) flash, no PSRAM
// FIXME: implement SX12 module type autodetection and have setup for each case (add E32 support)
// E32 has same pinout except having extra pins. I assume that the GND on it is connected internally to other GNDs so it is not a
// problem to NC the extra GND pins.
// For each EBYTE module pin in this section, provide the pin number of the ESP32-S3 you connected it to
// The ESP32-S3 is great because YOU CAN USE PRACTICALLY ANY PINS for the connections, but avoid some pins (such as on the WROOM
// modules the following): strapping pins (except 0 as a user button input as it already has a pulldown resistor in typical
// application schematic) (0, 3, 45, 46), USB-reserved (19, 20), and pins which aren't present on the WROOM-2 module for
// compatiblity as it uses octal SPI, or are likely connected internally in either WROOM version (26-37), and avoid pins whose
// voltages are set by the SPI voltage (47, 48), and pins that don't exist (22-25) You can ALSO set the SPI pins (SX126X_CS,
// SX126X_SCK, SX126X_MISO, SX126X_MOSI) to any pin with the ESP32-S3 due to \ GPIO Matrix / IO MUX / RTC IO MUX \, and also the
// serial pins, but this isn't recommended for Serial0 as the WROOM modules have a 499 Ohm resistor on U0TXD (to reduce harmonics
// but also acting as a sort of protection)
// We have many free pins on the ESP32-S3-WROOM-X-Y module, perhaps it is best to use one of its pins to control TXEN, and use
// DIO2 as an extra interrupt, but right now Meshtastic does not benefit from having another interrupt pin available.
// Adding two 0-ohm links on your PCB design so that you can choose between the two modes for controlling the E22's TXEN would
// enable future software to make the most of an extra available interrupt pin
// Possible improvement: can add extremely low resistance MOSFET to physically toggle power to E22 module when in full sleep (not
// waiting for interrupt)?
// PA stands for Power Amplifier, used when transmitting to increase output power
// LNA stands for Low Noise Amplifier, used when \ listening for / receiving \ data to increase sensitivity
//////////////////////////////////////////////////////////////////////////////////
// //
// Have custom connections or functionality? Configure them in this section //
// //
//////////////////////////////////////////////////////////////////////////////////
#define SX126X_CS 14 // EBYTE module's NSS pin // FIXME: rename to SX126X_SS
#define LORA_SCK 21 // EBYTE module's SCK pin
#define LORA_MOSI 38 // EBYTE module's MOSI pin
#define LORA_MISO 39 // EBYTE module's MISO pin
#define SX126X_RESET 40 // EBYTE module's NRST pin
#define SX126X_BUSY 41 // EBYTE module's BUSY pin
#define SX126X_DIO1 42 // EBYTE module's DIO1 pin
// We don't define a pin for SX126X_DIO2 as Meshtastic doesn't use it as an interrupt output, so it is never connected to an MCU
// pin! Also E22 module datasheets say not to connect it to an MCU pin.
// We don't define a pin for SX126X_DIO3 as Meshtastic doesn't use it as an interrupt output, so it is never connected to an MCU
// pin! Also E22 module datasheets say to use it as the TCXO's reference voltage.
// E32 module (which uses SX1276) may not have ability to set TCXO voltage using a DIO pin.
// The radio module needs to be told whether to enable RX mode or TX mode. Each radio module takes different actions based on
// these values, but generally the path from the antenna to SX1262 is changed from signal output to signal input. Also, if there
// are LNAs (Low-Noise Amplifiers) or PAs (Power Amplifiers) in the output or input paths, their power is also controlled by
// these pins. You should never have both TXEN and RXEN set high, this can cause problems for some radio modules, and is
// commonly referred to as 'undefined behaviour' in datasheets. For the SX1262, you shouldn't connect DIO2 to the MCU. DIO2 is
// an output only, and can be controlled via SPI instructions, the use for this is to save an MCU pin by using the DIO2 pin to
// control the RF switching mode.
// Choose ONLY ONE option from below, comment in/out the '/*'s and '*/'s
// SX126X_TXEN is the E22's [SX1262's] TXEN pin, SX126X_RXEN is the E22's [SX1262's] RXEN pin
// Option 1: E22's TXEN pin connected to E22's DIO2 pin, E22's RXEN pin connected to NEGATED output of E22's DIO2 pin (more
// expensive option hardware-wise, is the 'most proper' way, removes need for routing one/two traces from MCU to RF switching
// pins), however you can't have E22 in low-power 'sleep' mode (TXEN and RXEN both low cannot be achieved this this option).
/*
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_TXEN RADIOLIB_NC
#define SX126X_RXEN RADIOLIB_NC
*/
// Option 2: E22's TXEN pin connected to E22's DIO2 pin, E22's RXEN pin connected to MCU pin (cheaper option hardware-wise,
// removes need for routing another trace from MCU to an RF switching pin).
// /*
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_TXEN RADIOLIB_NC
#define SX126X_RXEN 10
// */
// Option 3: E22's TXEN pin connected to MCU pin, E22's RXEN pin connected to MCU pin (cheaper option hardware-wise, allows for
// ramping up PA before transmission (add/expand on feature yourself in RadioLib) if PA takes a while to stabilise)
// Don't define DIO2_AS_RF_SWITCH because we only use DIO2 or an MCU pin mutually exclusively to connect to E22's TXEN (to prevent
// a short if they are both connected at the same time (suboptimal PCB design) and there's a slight non-neglibible delay and/or
// voltage difference between DIO2 and TXEN). Can use DIO2 as an IRQ (but not in Meshtastic at the moment).
/*
#define SX126X_TXEN 9
#define SX126X_RXEN 10
*/
// (NOT RECOMMENDED, if need to ramp up PA before transmission, better to use option 3)
// Option 4: E22's TXEN pin connected to MCU pin, E22's RXEN pin connected to NEGATED output of E22's DIO2 pin (more expensive
// option hardware-wise, allows for ramping up PA before transmission (add/expand on feature yourself in RadioLib) if PA takes
// a while to stabilise, removes need for routing another trace from MCU to an RF switching pin, however may mean if in
// RadioLib you don't tell DIO2 to go high to indicate transmission (so the negated output goes to RXEN to turn the LNA off)
// then you may end up enabling E22's TXEN and RXEN pins at the same time whilst you ramp up the PA which is not ideal,
// changing DIO2's switching advance in RadioLib may not even be possible, may be baked into the SX126x).
/*
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_TXEN 9
#define SX126X_RXEN RADIOLIB_NC
*/
// Status
#define LED_POWER 1
#define LED_STATE_ON 1 // State when LED is lit
// External notification
// FIXME: Check if EXT_NOTIFY_OUT actualy has any effect and removes the need for setting the external notication pin in the
// app/preferences
#define EXT_NOTIFY_OUT 2 // The GPIO pin that acts as the external notification output (here we connect an LED to it)
// Buzzer
#define PIN_BUZZER 11
// Buttons
#define BUTTON_PIN 0 // Use the BOOT button as the user button
// I2C
#define I2C_SCL 18
#define I2C_SDA 8
// UART
#define UART_TX 43
#define UART_RX 44
// Power
// Outputting 22dBm from SX1262 results in ~30dBm E22-900M30S output (module only uses last stage of the YP2233W PA)
// Respect local regulations! If your E22-900M30S outputs the advertised 30 dBm and you use a 6 dBi antenna, you are at the
// equivalent of 36 EIRP (Effective Isotropic Radiated Power), which in this case is the limit for non-HAM users in the US (4W
// EIRP, at SPECIFIC frequencies).
// In the EU (and UK), as of now, you are allowed 27 dBm ERP which is 29.15 EIRP.
// https://eur-lex.europa.eu/legal-content/EN/TXT/?uri=CELEX:32022D0180
// https://www.legislation.gov.uk/uksi/1999/930/schedule/6/made
// To respect the 29.15 dBm EIRP (at SPECIFIC frequencies, others are lower) EU limit with a 2.5 dBi gain antenna, consulting
// https://github.com/S5NC/EBYTE_ESP32-S3/blob/main/power%20testing.txt, assuming 0.1 dBm insertion loss, output 20 dBm from the
// E22-900M30S's SX1262. It is worth noting that if you are in this situation and don't have a HAM license, you may be better off
// with a lower gain antenna, and output the difference as a higher total power input into the antenna, as your EIRP would be the
// same, but you would get a wider angle of coverage. Also take insertion loss and possibly VSWR into account
// (https://www.everythingrf.com/tech-resources/vswr). Please check regulations yourself and check airtime, usage (for example
// whether you are airborne), frequency, and power laws.
#define SX126X_MAX_POWER 22 // SX126xInterface.cpp defaults to 22 if not defined, but here we define it for good practice
// Display
// FIXME: change behavior in src to default to not having screen if is undefined
// FIXME: remove 0/1 option for HAS_SCREEN in src, change to being defined or not
// FIXME: check if it actually causes a crash when not specifiying that a display isn't present
#define HAS_SCREEN 0 // Assume no screen present by default to prevent crash...
// GPS
// FIXME: unsure what to define HAS_GPS as if GPS isn't always present
#define HAS_GPS 1 // Don't need to set this to 0 to prevent a crash as it doesn't crash if GPS not found, will probe by default
#define PIN_GPS_EN 15
#define GPS_EN_ACTIVE 1
#define GPS_TX_PIN 16
#define GPS_RX_PIN 17
/////////////////////////////////////////////////////////////////////////////////
// //
// You should have no need to modify the code below, nor in pins_arduino.h //
// //
/////////////////////////////////////////////////////////////////////////////////
#define USE_SX1262 // E22-900M30S, E22-900M22S, and E22-900MM22S (not E220!) use SX1262
#define USE_SX1268 // E22-400M30S, E22-400M33S, E22-400M22S, and E22-400MM22S use SX1268
// The below isn't needed as we directly define SX126X_TXEN and SX126X_RXEN instead of using proxies E22_TXEN and E22_RXEN
/*
// FALLBACK: If somehow E22_TXEN isn't defined or clearly isn't a valid pin number, set it to RADIOLIB_NC to avoid SX126X_TXEN
being defined but having no value #if (!defined(E22_TXEN) || !(0 <= E22_TXEN && E22_TXEN <= 48)) #define E22_TXEN RADIOLIB_NC
#endif
// FALLBACK: If somehow E22_RXEN isn't defined or clearly isn't a valid pin number, set it to RADIOLIB_NC to avoid SX126X_RXEN
being defined but having no value #if (!defined(E22_RXEN) || !(0 <= E22_RXEN && E22_RXEN <= 48)) #define E22_RXEN RADIOLIB_NC
#endif
#define SX126X_TXEN E22_TXEN
#define SX126X_RXEN E22_RXEN
*/
// E22 series TCXO voltage is 1.8V per https://www.ebyte.com/en/pdf-down.aspx?id=781 (source
// https://github.com/jgromes/RadioLib/issues/12#issuecomment-520695575), so set it as such
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#define LORA_CS SX126X_CS // FIXME: for some reason both are used in /src
// Many of the below values would only be used if USE_RF95 was defined, but it's not as we aren't actually using an RF95, just
// that the 4 pins above are named like it If they aren't used they don't need to be defined and doing so cause confusion to those
// adapting this file LORA_RESET value is never used in src (as we are not using RF95), so no need to define LORA_DIO0 is not used
// in src (as we are not using RF95) as SX1262 does not have it per SX1262 datasheet, so no need to define
// FIXME: confirm that the linked lines below are actually only called when using the SX126x or SX128x and no other modules
// then use SX126X_DIO1 and SX128X_DIO1 respectively for that purpose, removing the need for RF95-style LORA_* definitions when
// the RF95 isn't used
#define LORA_DIO1 \
SX126X_DIO1 // The old name is used in
// https://github.com/meshtastic/firmware/blob/7eff5e7bcb2084499b723c5e3846c15ee089e36d/src/sleep.cpp#L298, so
// must also define the old name
// LORA_DIO2 value is never used in src (as we are not using RF95), so no need to define, and if DIO2_AS_RF_SWITCH is set then it
// cannot serve any extra function even if requested to LORA_DIO3 value is never used in src (as we are not using RF95), so no
// need to define, and DIO3_AS_TCXO_AT_1V8 is set so it cannot serve any extra function even if requested to (from 13.3.2.1
// DioxMask in SX1262 datasheet: Note that if DIO2 or DIO3 are used to control the RF Switch or the TCXO, the IRQ will not be
// generated even if it is mapped to the pins.)
code/firmware/variants/esp32s3/ELECROW-ThinkNode-M2/pins_arduino.h
+28
View File
@@ -0,0 +1,28 @@
// Need this file for ESP32-S3
// No need to modify this file, changes to pins imported from variant.h
// Most is similar to https://github.com/espressif/arduino-esp32/blob/master/variants/esp32s3/pins_arduino.h
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#include <variant.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// Serial
static const uint8_t TX = UART_TX;
static const uint8_t RX = UART_RX;
// Default SPI will be mapped to Radio
static const uint8_t SS = LORA_CS;
static const uint8_t SCK = LORA_SCK;
static const uint8_t MOSI = LORA_MOSI;
static const uint8_t MISO = LORA_MISO;
// The default Wire will be mapped to PMU and RTC
static const uint8_t SCL = I2C_SCL;
static const uint8_t SDA = I2C_SDA;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/ELECROW-ThinkNode-M2/platformio.ini
+17
View File
@@ -0,0 +1,17 @@
[env:thinknode_m2]
custom_meshtastic_hw_model = 90
custom_meshtastic_hw_model_slug = THINKNODE_M2
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = ThinkNode M2
custom_meshtastic_images = thinknode_m2.svg
custom_meshtastic_tags = Elecrow
custom_meshtastic_requires_dfu = false
extends = esp32s3_base
board = ESP32-S3-WROOM-1-N4
build_flags =
${esp32s3_base.build_flags}
-D ELECROW_ThinkNode_M2
-I variants/esp32s3/ELECROW-ThinkNode-M2
code/firmware/variants/esp32s3/ELECROW-ThinkNode-M2/variant.h
+61
View File
@@ -0,0 +1,61 @@
// Status
#define LED_POWER 1
#define PIN_BUTTON1 47 // 功能键
#define PIN_BUTTON2 4 // 电源键
#define ALT_BUTTON_PIN PIN_BUTTON2
#define ALT_BUTTON_ACTIVE_LOW false
#define ALT_BUTTON_ACTIVE_PULLUP false
#define LED_POWER 6
#define ADC_V 42
// USB_CHECK
#define EXT_PWR_DETECT 7
#define PIN_BUZZER 5
#define I2C_SCL 15
#define I2C_SDA 16
#define UART_TX 43
#define UART_RX 44
#define VEXT_ENABLE 46 // for OLED
#define VEXT_ON_VALUE HIGH
#define SX126X_CS 10
#define LORA_SCK 12
#define LORA_MOSI 11
#define LORA_MISO 13
#define SX126X_RESET 21
#define SX126X_BUSY 14
#define SX126X_DIO1 3
#define SX126X_DIO2_AS_RF_SWITCH
// #define SX126X_DIO3 9
#define SX126X_DIO3_TCXO_VOLTAGE 3.3
#define SX126X_MAX_POWER 22 // SX126xInterface.cpp defaults to 22 if not defined, but here we define it for good practice
#define USE_SX1262
#define LORA_CS SX126X_CS // FIXME: for some reason both are used in /src
#define LORA_DIO1 SX126X_DIO1
#define SX126X_POWER_EN 48
// Battery
// #define BATTERY_PIN 2
#define BATTERY_PIN 17
// #define ADC_CHANNEL ADC1_GPIO2_CHANNEL
#define ADC_CHANNEL ADC2_GPIO17_CHANNEL
#define BATTERY_SENSE_RESOLUTION_BITS 12
#define BATTERY_SENSE_RESOLUTION 4096.0
#undef AREF_VOLTAGE
#define AREF_VOLTAGE 3.0
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
#define ADC_MULTIPLIER (1.548F)
#define BAT_MEASURE_ADC_UNIT 2
#define HAS_SCREEN 1
#define USE_SH1106 1
#define HAS_GPS 0
#define BUTTON_PIN PIN_BUTTON1
code/firmware/variants/esp32s3/ELECROW-ThinkNode-M5/pins_arduino.h
+28
View File
@@ -0,0 +1,28 @@
// Need this file for ESP32-S3
// No need to modify this file, changes to pins imported from variant.h
// Most is similar to https://github.com/espressif/arduino-esp32/blob/master/variants/esp32s3/pins_arduino.h
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#include <variant.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// Serial
static const uint8_t TX = UART_TX;
static const uint8_t RX = UART_RX;
// Default SPI will be mapped to Radio
static const uint8_t SS = LORA_CS;
static const uint8_t SCK = LORA_SCK;
static const uint8_t MOSI = LORA_MOSI;
static const uint8_t MISO = LORA_MISO;
// The default Wire will be mapped to PMU and RTC
static const uint8_t SCL = I2C_SCL;
static const uint8_t SDA = I2C_SDA;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/ELECROW-ThinkNode-M5/platformio.ini
+38
View File
@@ -0,0 +1,38 @@
[env:thinknode_m5]
custom_meshtastic_hw_model = 107
custom_meshtastic_hw_model_slug = THINKNODE_M5
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = ThinkNode M5
custom_meshtastic_images = thinknode_m1.svg
custom_meshtastic_tags = Elecrow
custom_meshtastic_requires_dfu = false
extends = esp32s3_base
board = ESP32-S3-WROOM-1-N4
build_src_filter =
${esp32s3_base.build_src_filter}
+<../variants/esp32s3/ELECROW-ThinkNode-M5>
build_flags =
${esp32s3_base.build_flags}
-D ELECROW_ThinkNode_M5
-I variants/esp32s3/ELECROW-ThinkNode-M5
-DEINK_DISPLAY_MODEL=GxEPD2_154_D67
-DEINK_WIDTH=200
-DEINK_HEIGHT=200
-DUSE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
-DEINK_LIMIT_FASTREFRESH=10 ; How many consecutive fast-refreshes are permitted //20
-DEINK_LIMIT_RATE_BACKGROUND_SEC=10 ; Minimum interval between BACKGROUND updates //30
-DEINK_LIMIT_RATE_RESPONSIVE_SEC=1 ; Minimum interval between RESPONSIVE updates
; -DEINK_LIMIT_GHOSTING_PX=2000 ; (Optional) How much image ghosting is tolerated
-DEINK_BACKGROUND_USES_FAST ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
lib_deps = ${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
# renovate: datasource=custom.pio depName=PCA9557-arduino packageName=maxpromer/library/PCA9557-arduino
maxpromer/PCA9557-arduino@1.0.0
# renovate: datasource=custom.pio depName=SensorLib packageName=lewisxhe/library/SensorLib
lewisxhe/SensorLib@0.3.4
code/firmware/variants/esp32s3/ELECROW-ThinkNode-M5/variant.cpp
+23
View File
@@ -0,0 +1,23 @@
#include "variant.h"
#include <PCA9557.h>
PCA9557 io(0x18, &Wire1);
void earlyInitVariant()
{
Wire1.begin(48, 47);
io.pinMode(PCA_PIN_EINK_EN, OUTPUT);
io.pinMode(PCA_PIN_POWER_EN, OUTPUT);
io.pinMode(PCA_LED_POWER, OUTPUT);
io.pinMode(PCA_LED_USER, OUTPUT);
io.pinMode(PCA_LED_ENABLE, OUTPUT);
io.digitalWrite(PCA_PIN_POWER_EN, HIGH);
io.digitalWrite(PCA_LED_USER, LOW);
io.digitalWrite(PCA_LED_ENABLE, LOW);
}
void variant_shutdown()
{
io.digitalWrite(PCA_PIN_POWER_EN, LOW);
}
code/firmware/variants/esp32s3/ELECROW-ThinkNode-M5/variant.h
+91
View File
@@ -0,0 +1,91 @@
#ifndef ELECROW_ThinkNode_M5_VAR
#define ELECROW_ThinkNode_M5_VAR
#define UART_TX 43
#define UART_RX 44
#define HAS_PCA9557
// LED
// Both of these are on the GPIO expander
#define PCA_LED_USER 1 // the Blue LED
#define PCA_LED_ENABLE 2 // the power supply to the LEDs, in an OR arrangement with VBUS power
#define PCA_LED_POWER 3 // the Red LED? Seems to have hardware logic to blink when USB is plugged in.
#define POWER_LED_HARDWARE_BLINKS_WHILE_CHARGING
// USB_CHECK
#define EXT_PWR_DETECT 12
#define BATTERY_PIN 8
#define ADC_CHANNEL ADC1_GPIO8_CHANNEL
#define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
#define PIN_BUZZER 9
// Buttons
#define PIN_BUTTON2 14
#define PIN_BUTTON1 21
// Wire Interfaces
#define I2C_SCL 1
#define I2C_SDA 2
// PCF8563 RTC Module
#define PCF8563_RTC 0x51
// GPS pins
#define GPS_SWITH 10
#define HAS_GPS 1
#define GPS_L76K
#define PIN_GPS_REINIT 13 // An output to reset L76K GPS. As per datasheet, low for > 100ms will reset the L76K
#define PIN_GPS_STANDBY 11 // An output to wake GPS, low means allow sleep, high means force wake
#define GPS_TX_PIN 20 // This is for bits going TOWARDS the CPU
#define GPS_RX_PIN 19 // This is for bits going TOWARDS the GPS
#define GPS_THREAD_INTERVAL 50
#define PIN_SERIAL1_RX GPS_TX_PIN
#define PIN_SERIAL1_TX GPS_RX_PIN
#define SX126X_CS 17
#define LORA_SCK 16
#define LORA_MOSI 15
#define LORA_MISO 7
#define SX126X_RESET 6
#define SX126X_BUSY 5
#define SX126X_DIO1 4
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 3.3
#define SX126X_POWER_EN 46
#define SX126X_MAX_POWER 22 // SX126xInterface.cpp defaults to 22 if not defined, but here we define it for good practice
#define USE_SX1262
#define LORA_CS SX126X_CS // FIXME: for some reason both are used in /src
#define LORA_DIO1 SX126X_DIO1
#define USE_EINK
// Note: this is really just backlight power
#define PCA_PIN_EINK_EN 5 // This is the pin number on the GPIO expander
#define PIN_EINK_CS 39
#define PIN_EINK_BUSY 42
#define PIN_EINK_DC 40
#define PIN_EINK_RES 41
#define PIN_EINK_SCLK 38
#define PIN_EINK_MOSI 45 // also called SDI
// Controls power for all peripherals (eink + GPS + LoRa + Sensor)
#define PIN_POWER_EN -1
#define PCA_PIN_POWER_EN 4 // This is the pin number on the GPIO expander
#define PIN_SPI_MISO 7
#define PIN_SPI_MOSI 15
#define PIN_SPI_SCK 16
#define BUTTON_PIN PIN_BUTTON1
#define BUTTON_PIN_ALT PIN_BUTTON2
#define SERIAL_PRINT_PORT 0
#endif
code/firmware/variants/esp32s3/bpi_picow_esp32_s3/pins_arduino.h
+29
View File
@@ -0,0 +1,29 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
static const uint8_t TX = 43;
static const uint8_t RX = 44;
// The default Wire will be mapped to PMU and RTC
static const uint8_t SDA = 12;
static const uint8_t SCL = 14;
// Default SPI will be mapped to Radio
static const uint8_t MISO = 39;
static const uint8_t SCK = 21;
static const uint8_t MOSI = 38;
static const uint8_t SS = 17;
// #define SPI_MOSI (11)
// #define SPI_SCK (14)
// #define SPI_MISO (2)
// #define SPI_CS (13)
// #define SDCARD_CS SPI_CS
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/bpi_picow_esp32_s3/platformio.ini
+17
View File
@@ -0,0 +1,17 @@
[env:bpi_picow_esp32_s3]
extends = esp32s3_base
board = bpi_picow_esp32_s3
board_level = extra
;OpenOCD flash method
;upload_protocol = esp-builtin
;Normal method
upload_protocol = esptool
;upload_port = /dev/ttyACM2
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=caveman99-ESP32_Codec2 packageName=caveman99/library/ESP32 Codec2
caveman99/ESP32 Codec2@1.0.1
build_flags =
${esp32s3_base.build_flags}
-D PRIVATE_HW
-I variants/esp32s3/bpi_picow_esp32_s3
code/firmware/variants/esp32s3/bpi_picow_esp32_s3/variant.h
+74
View File
@@ -0,0 +1,74 @@
#define HAS_GPS 0
#undef GPS_RX_PIN
#undef GPS_TX_PIN
// #define HAS_SCREEN 0
// #define HAS_SDCARD
// #define SDCARD_USE_SPI1
#define USE_SSD1306
#define I2C_SDA 12
#define I2C_SCL 14
#define LED_POWER 46
#define LED_STATE_ON 0 // State when LED is litted
// #define BUTTON_PIN 15 // Pico OLED 1.3 User key 0 - removed User key 1 (17)
#define BUTTON_PIN 40
// #define BUTTON_PIN 0 // This is the BOOT button pad at the moment
// #define BUTTON_NEED_PULLUP
// #define USE_RF95 // RFM95/SX127x
#undef LORA_SCK
#undef LORA_MISO
#undef LORA_MOSI
#undef LORA_CS
// WaveShare Core1262-868M OK
// https://www.waveshare.com/wiki/Core1262-868M
#define USE_SX1262
#ifdef USE_SX1262
#define LORA_MISO 39
#define LORA_SCK 21
#define LORA_MOSI 38
#define LORA_CS 17
#define LORA_RESET 42
#define LORA_DIO1 5
#define LORA_BUSY 47
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_BUSY
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#endif
// #define USE_SX1280
#ifdef USE_SX1280
#define LORA_MISO 1
#define LORA_SCK 3
#define LORA_MOSI 4
#define LORA_CS 2
#define LORA_RESET 17
#define LORA_DIO1 12
#define LORA_BUSY 47
#define SX128X_CS LORA_CS
#define SX128X_DIO1 LORA_DIO1
#define SX128X_BUSY LORA_BUSY
#define SX128X_RESET LORA_RESET
#endif
// #define USE_EINK
/*
* eink display pins
*/
// #define PIN_EINK_CS
// #define PIN_EINK_BUSY
// #define PIN_EINK_DC
// #define PIN_EINK_RES (-1)
// #define PIN_EINK_SCLK 3
// #define PIN_EINK_MOSI 4
code/firmware/variants/esp32s3/crowpanel-esp32s3-5-epaper/pins_arduino.h
+26
View File
@@ -0,0 +1,26 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// The default Wire will be mapped to PMU and RTC
static const uint8_t SDA = 21;
static const uint8_t SCL = 15;
// Default SPI will be mapped to Radio
static const uint8_t SS = 14;
static const uint8_t MOSI = 8;
static const uint8_t MISO = 9;
static const uint8_t SCK = 3;
#define SPI_MOSI (40)
#define SPI_SCK (39)
#define SPI_MISO (13)
#define SPI_CS (10)
// IO42 TF_3V3_CTL
#define SDCARD_CS SPI_CS
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/crowpanel-esp32s3-5-epaper/platformio.ini
+89
View File
@@ -0,0 +1,89 @@
[env:crowpanel-esp32s3-5-epaper]
extends = esp32s3_base
board_build.arduino.memory_type = qio_opi
board_build.flash_mode = qio
board_build.psram_type = opi
board_upload.flash_size = 8MB
board_upload.maximum_size = 8388608
board_build.partitions = default_8MB.csv
board = esp32-s3-devkitc-1
;upload_port = /dev/ttyUSB0
board_level = extra
upload_protocol = esptool
build_flags =
${esp32s3_base.build_flags}
-D CROWPANEL_ESP32S3_5_EPAPER
-I variants/esp32s3/crowpanel-esp32s3-5-epaper
-D PRIVATE_HW
-DBOARD_HAS_PSRAM
-DEINK_DISPLAY_MODEL=GxEPD2_579_GDEY0579T93 ;https://www.good-display.com/product/439.html
-DEINK_WIDTH=792
-DEINK_HEIGHT=272
-DUSE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
-DEINK_LIMIT_FASTREFRESH=100 ; How many consecutive fast-refreshes are permitted
;-DEINK_LIMIT_RATE_BACKGROUND_SEC=30 ; Minimum interval between BACKGROUND updates
;-DEINK_LIMIT_RATE_RESPONSIVE_SEC=1
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
[env:crowpanel-esp32s3-4-epaper]
extends = esp32s3_base
board_build.arduino.memory_type = qio_opi
board_build.flash_mode = qio
board_build.psram_type = opi
board_upload.flash_size = 8MB
board_upload.maximum_size = 8388608
board_build.partitions = default_8MB.csv
board = esp32-s3-devkitc-1
;upload_port = /dev/ttyUSB0
board_level = extra
upload_protocol = esptool
build_flags =
${esp32s3_base.build_flags}
-D CROWPANEL_ESP32S3_4_EPAPER
-I variants/esp32s3/crowpanel-esp32s3-5-epaper
-D PRIVATE_HW
-DBOARD_HAS_PSRAM
-DEINK_DISPLAY_MODEL=GxEPD2_420_GYE042A87 ; similar Panel: GDEY042T81 : https://www.good-display.com/product/386.html
-DEINK_WIDTH=400
-DEINK_HEIGHT=300
-DUSE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
-DEINK_LIMIT_FASTREFRESH=100 ; How many consecutive fast-refreshes are permitted
;-DEINK_LIMIT_RATE_BACKGROUND_SEC=30 ; Minimum interval between BACKGROUND updates
;-DEINK_LIMIT_RATE_RESPONSIVE_SEC=1
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
[env:crowpanel-esp32s3-2-epaper]
extends = esp32s3_base
board_build.arduino.memory_type = qio_opi
board_build.flash_mode = qio
board_build.psram_type = opi
board_upload.flash_size = 8MB
board_upload.maximum_size = 8388608
board_build.partitions = default_8MB.csv
board = esp32-s3-devkitc-1
;upload_port = /dev/ttyUSB0
board_level = extra
upload_protocol = esptool
build_flags =
${esp32s3_base.build_flags}
-D CROWPANEL_ESP32S3_2_EPAPER
-I variants/esp32s3/crowpanel-esp32s3-5-epaper
-D PRIVATE_HW
-DBOARD_HAS_PSRAM
-DEINK_DISPLAY_MODEL=GxEPD2_290_GDEY029T94 ;https://www.good-display.com/product/389.html
-DEINK_WIDTH=296
-DEINK_HEIGHT=128
-DUSE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
-DEINK_LIMIT_FASTREFRESH=100 ; How many consecutive fast-refreshes are permitted
;-DEINK_LIMIT_RATE_BACKGROUND_SEC=30 ; Minimum interval between BACKGROUND updates
;-DEINK_LIMIT_RATE_RESPONSIVE_SEC=1
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
code/firmware/variants/esp32s3/crowpanel-esp32s3-5-epaper/variant.h
+77
View File
@@ -0,0 +1,77 @@
#define HAS_SDCARD
#define SDCARD_USE_SPI1
// Display (E-Ink)
#define USE_EINK
#define PIN_EINK_CS 45
#define PIN_EINK_BUSY 48
#define PIN_EINK_DC 46
#define PIN_EINK_RES 47
#define PIN_EINK_SCLK 12
#define PIN_EINK_MOSI 11
#define VEXT_ENABLE 7 // e-ink power enable pin
#define VEXT_ON_VALUE HIGH
#define PIN_POWER_EN 42 // TF/SD Card Power Enable Pin
// #define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to
// measure battery voltage ratio of voltage divider = 2.0 (assumption)
// #define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
// #define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define I2C_SDA SDA // 21
#define I2C_SCL SCL // 15
#define GPS_DEFAULT_NOT_PRESENT 1
// #define GPS_RX_PIN 44
// #define GPS_TX_PIN 43
#define LED_POWER 41
#define BUTTON_PIN 2
#define BUTTON_NEED_PULLUP
// Buzzer - noisy ?
#define PIN_BUZZER (0 + 18)
// Wheel
// Up 6
// Push 5
// Down 4
// MENU Top 2
// EXIT Bottom 1
// TTGO uses a common pinout for their SX1262 vs RF95 modules - both can be enabled and
// we will probe at runtime for RF95 and if not found then probe for SX1262
// #define USE_RF95 // RFM95/SX127x
#define USE_SX1262
// #define USE_SX1280
#define LORA_SCK 3
#define LORA_MISO 9
#define LORA_MOSI 8
#define LORA_CS 14
#define LORA_RESET 38
#define LORA_DIO1 16
#define LORA_DIO2 17
// per SX1262_Receive_Interrupt/utilities.h
#ifdef USE_SX1262
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#endif
// per SX128x_Receive_Interrupt/utilities.h
#ifdef USE_SX1280
#define SX128X_CS LORA_CS
#define SX128X_DIO1 LORA_DIO1
#define SX128X_BUSY LORA_DIO2
#define SX128X_RESET LORA_RESET
#define SX128X_RXEN 21
#define SX128X_TXEN 15
#define SX128X_MAX_POWER 3
#endif
code/firmware/variants/esp32s3/diy/my_esp32s3_diy_eink/pins_arduino.h
+26
View File
@@ -0,0 +1,26 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// The default Wire will be mapped to PMU and RTC
static const uint8_t SDA = 18;
static const uint8_t SCL = 17;
// Default SPI will be mapped to Radio
static const uint8_t MISO = 3;
static const uint8_t SCK = 5;
static const uint8_t MOSI = 6;
static const uint8_t SS = 7;
// #define SPI_MOSI (11)
// #define SPI_SCK (14)
// #define SPI_MISO (2)
// #define SPI_CS (13)
// #define SDCARD_CS SPI_CS
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/diy/my_esp32s3_diy_eink/platformio.ini
+30
View File
@@ -0,0 +1,30 @@
[env:my-esp32s3-diy-eink]
board_level = extra
extends = esp32s3_base
board = my_esp32s3_diy_eink
board_build.arduino.memory_type = dio_opi
board_build.mcu = esp32s3
board_build.f_cpu = 240000000L
upload_protocol = esptool
;upload_port = /dev/ttyACM1
upload_speed = 921600
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
zinggjm/GxEPD2@1.6.7
# renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
adafruit/Adafruit NeoPixel@1.15.4
build_unflags =
${esp32s3_base.build_unflags}
-DARDUINO_USB_MODE=1
build_flags =
${esp32s3_base.build_flags}
-D PRIVATE_HW
-I variants/esp32s3/diy/my_esp32s3_diy_eink
-Dmy
-DEINK_DISPLAY_MODEL=GxEPD2_290_T5D
-DEINK_WIDTH=296
-DEINK_HEIGHT=128
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DARDUINO_USB_MODE=0
code/firmware/variants/esp32s3/diy/my_esp32s3_diy_eink/variant.h
+60
View File
@@ -0,0 +1,60 @@
#define HAS_GPS 0
#undef GPS_RX_PIN
#undef GPS_TX_PIN
// #define HAS_SCREEN 0
// #define HAS_SDCARD
// #define SDCARD_USE_SPI1
// #define USE_SSD1306
#define I2C_SDA 18 // 1 // I2C pins for this board
#define I2C_SCL 17 // 2
// #define LED_POWER 38 // This is a RGB LED not a standard LED
#define HAS_NEOPIXEL // Enable the use of neopixels
#define NEOPIXEL_COUNT 1 // How many neopixels are connected
#define NEOPIXEL_DATA 38 // gpio pin used to send data to the neopixels
#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
#define BUTTON_PIN 0 // This is the BOOT button
#define BUTTON_NEED_PULLUP
// #define USE_RF95 // RFM95/SX127x
// #define USE_SX1262
#define USE_SX1280
#define LORA_MISO 3
#define LORA_SCK 5
#define LORA_MOSI 6
#define LORA_CS 7
#define LORA_RESET 8
#define LORA_DIO1 16
#ifdef USE_SX1262
#define SX126X_CS LORA_CS // FIXME - we really should define LORA_CS instead
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY 15
#define SX126X_RESET LORA_RESET
#define SX126X_RXEN 4
#define SX126X_TXEN 9
#endif
#ifdef USE_SX1280
#define SX128X_CS LORA_CS
#define SX128X_DIO1 LORA_DIO1
#define SX128X_BUSY 15
#define SX128X_RESET LORA_RESET
#endif
#define USE_EINK
/*
* eink display pins
*/
#define PIN_EINK_CS 13
#define PIN_EINK_BUSY 2
#define PIN_EINK_DC 1
#define PIN_EINK_RES (-1)
#define PIN_EINK_SCLK 5
#define PIN_EINK_MOSI 6
code/firmware/variants/esp32s3/diy/my_esp32s3_diy_oled/pins_arduino.h
+26
View File
@@ -0,0 +1,26 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// The default Wire will be mapped to PMU and RTC
static const uint8_t SDA = 18;
static const uint8_t SCL = 17;
// Default SPI will be mapped to Radio
static const uint8_t MISO = 3;
static const uint8_t SCK = 5;
static const uint8_t MOSI = 6;
static const uint8_t SS = 7;
// #define SPI_MOSI (11)
// #define SPI_SCK (14)
// #define SPI_MISO (2)
// #define SPI_CS (13)
// #define SDCARD_CS SPI_CS
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/diy/my_esp32s3_diy_oled/platformio.ini
+24
View File
@@ -0,0 +1,24 @@
[env:my-esp32s3-diy-oled]
board_level = extra
extends = esp32s3_base
board = my-esp32s3-diy-oled
board_build.arduino.memory_type = dio_opi
board_build.mcu = esp32s3
board_build.f_cpu = 240000000L
upload_protocol = esptool
;upload_port = /dev/ttyACM0
upload_speed = 921600
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
adafruit/Adafruit NeoPixel@1.15.4
build_unflags =
${esp32s3_base.build_unflags}
-DARDUINO_USB_MODE=1
build_flags =
${esp32s3_base.build_flags}
-D PRIVATE_HW
-I variants/esp32s3/diy/my_esp32s3_diy_oled
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DARDUINO_USB_MODE=0
code/firmware/variants/esp32s3/diy/my_esp32s3_diy_oled/variant.h
+60
View File
@@ -0,0 +1,60 @@
#define HAS_GPS 0
#undef GPS_RX_PIN
#undef GPS_TX_PIN
// #define HAS_SCREEN 0
// #define HAS_SDCARD
// #define SDCARD_USE_SPI1
#define USE_SSD1306
#define I2C_SDA 18 // 1 // I2C pins for this board
#define I2C_SCL 17 // 2
// #define LED_POWER 38 // This is a RGB LED not a standard LED
#define HAS_NEOPIXEL // Enable the use of neopixels
#define NEOPIXEL_COUNT 1 // How many neopixels are connected
#define NEOPIXEL_DATA 38 // gpio pin used to send data to the neopixels
#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
#define BUTTON_PIN 0 // This is the BOOT button
#define BUTTON_NEED_PULLUP
// #define USE_RF95 // RFM95/SX127x
// #define USE_SX1262
#define USE_SX1280
#define LORA_MISO 3
#define LORA_SCK 5
#define LORA_MOSI 6
#define LORA_CS 7
#define LORA_RESET 8
#define LORA_DIO1 16
#ifdef USE_SX1262
#define SX126X_CS LORA_CS // FIXME - we really should define LORA_CS instead
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY 15
#define SX126X_RESET LORA_RESET
#define SX126X_RXEN 4
#define SX126X_TXEN 9
#endif
#ifdef USE_SX1280
#define SX128X_CS LORA_CS
#define SX128X_DIO1 LORA_DIO1
#define SX128X_BUSY 15
#define SX128X_RESET LORA_RESET
#endif
// #define USE_EINK
/*
* eink display pins
*/
// #define PIN_EINK_CS 13
// #define PIN_EINK_BUSY 2
// #define PIN_EINK_DC 1
// #define PIN_EINK_RES (-1)
// #define PIN_EINK_SCLK 5
// #define PIN_EINK_MOSI 6
code/firmware/variants/esp32s3/diy/t-energy-s3_e22/platformio.ini
+18
View File
@@ -0,0 +1,18 @@
; NanoVHF T-Energy-S3 + E22(0)-xxxM - DIY
[env:t-energy-s3_e22]
extends = esp32s3_base
board = esp32-s3-devkitc-1
board_build.partitions = default_16MB.csv
board_level = extra
board_upload.flash_size = 16MB ;Specify the FLASH capacity as 16MB
board_build.arduino.memory_type = qio_opi ;Enable internal PSRAM
build_unflags =
${esp32s3_base.build_unflags}
-D ARDUINO_USB_MODE=1
build_flags =
${esp32s3_base.build_flags}
-D EBYTE_ESP32_S3
-D BOARD_HAS_PSRAM
-D ARDUINO_USB_MODE=0
-D ARDUINO_USB_CDC_ON_BOOT=1
-I variants/esp32s3/diy/t-energy-s3_e22
code/firmware/variants/esp32s3/diy/t-energy-s3_e22/variant.h
+46
View File
@@ -0,0 +1,46 @@
// NanoVHF T-Energy-S3 + E22(0)-xxxM - DIY
// https://github.com/NanoVHF/Meshtastic-DIY/tree/main/PCB/ESP-32-devkit_EBYTE-E22/Mesh-v1.06-TTGO-T18
// Battery
#define BATTERY_PIN 3
#define ADC_MULTIPLIER 2.0
#define ADC_CHANNEL ADC1_GPIO3_CHANNEL
// Button on NanoVHF PCB
#define BUTTON_PIN 39
// I2C via connectors on NanoVHF PCB
#define I2C_SCL 2
#define I2C_SDA 42
// Screen (disabled)
#define HAS_SCREEN 0 // Assume no screen present by default to prevent crash...
// GPS via T-Energy-S3 onboard connector
#define HAS_GPS 1
#define GPS_TX_PIN 43
#define GPS_RX_PIN 44
// LoRa
#define USE_SX1262 // E22-900M30S, E22-900M22S, and E22-900MM22S (not E220!) use SX1262
#define USE_SX1268 // E22-400M30S, E22-400M33S, E22-400M22S, and E22-400MM22S use SX1268
#define SX126X_MAX_POWER 22 // SX126xInterface.cpp defaults to 22 if not defined, but here we define it for good practice
#define SX126X_DIO3_TCXO_VOLTAGE 1.8 // E22 series TCXO reference voltage is 1.8V
#define SX126X_CS 5 // EBYTE module's NSS pin // FIXME: rename to SX126X_SS
#define SX126X_SCK 6 // EBYTE module's SCK pin
#define SX126X_MOSI 13 // EBYTE module's MOSI pin
#define SX126X_MISO 4 // EBYTE module's MISO pin
#define SX126X_RESET 1 // EBYTE module's NRST pin
#define SX126X_BUSY 48 // EBYTE module's BUSY pin
#define SX126X_DIO1 47 // EBYTE module's DIO1 pin
#define SX126X_TXEN 10 // Schematic connects EBYTE module's TXEN pin to MCU
#define SX126X_RXEN 12 // Schematic connects EBYTE module's RXEN pin to MCU
#define LORA_CS SX126X_CS // Compatibility with variant file configuration structure
#define LORA_SCK SX126X_SCK // Compatibility with variant file configuration structure
#define LORA_MOSI SX126X_MOSI // Compatibility with variant file configuration structure
#define LORA_MISO SX126X_MISO // Compatibility with variant file configuration structure
#define LORA_DIO1 SX126X_DIO1 // Compatibility with variant file configuration structure
code/firmware/variants/esp32s3/dreamcatcher/platformio.ini
+31
View File
@@ -0,0 +1,31 @@
[env:dreamcatcher] ; 2301, latest revision
extends = esp32s3_base
board = esp32s3box
board_build.partitions = default_16MB.csv
board_level = extra
build_flags =
${esp32s3_base.build_flags}
-D PRIVATE_HW
-D OTHERNET_DC_REV=2301
-I variants/esp32s3/dreamcatcher
-D ARDUINO_USB_CDC_ON_BOOT=1
lib_deps = ${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
earlephilhower/ESP8266Audio@1.9.9
# renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
earlephilhower/ESP8266SAM@1.1.0
[env:dreamcatcher-2206]
extends = esp32s3_base
board = esp32s3box
board_build.partitions = default_16MB.csv
board_level = extra
build_flags =
${esp32s3_base.build_flags}
-D PRIVATE_HW
-D OTHERNET_DC_REV=2206
-I variants/esp32s3/dreamcatcher
-D ARDUINO_USB_CDC_ON_BOOT=1
code/firmware/variants/esp32s3/dreamcatcher/rfswitch.h
+17
View File
@@ -0,0 +1,17 @@
#include "RadioLib.h"
// RF Switch Matrix SubG RFO_HP_LF / RFO_LP_LF / RFI_[NP]_LF0
// DIO5 -> RFSW0_V1
// DIO6 -> RFSW1_V2
// DIO7 -> ANT_CTRL_ON + ESP_IO9/LR_GPS_ANT_DC_EN -> RFI_GPS (Bias-T GPS)
static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_LR11X0_DIO7, RADIOLIB_NC,
RADIOLIB_NC};
static const Module::RfSwitchMode_t rfswitch_table[] = {
// mode DIO5 DIO6 DIO7
{LR11x0::MODE_STBY, {LOW, LOW, LOW}}, {LR11x0::MODE_RX, {HIGH, LOW, LOW}},
{LR11x0::MODE_TX, {LOW, HIGH, LOW}}, {LR11x0::MODE_TX_HP, {LOW, HIGH, LOW}},
{LR11x0::MODE_TX_HF, {LOW, LOW, LOW}}, {LR11x0::MODE_GNSS, {LOW, LOW, HIGH}},
{LR11x0::MODE_WIFI, {LOW, LOW, LOW}}, END_OF_MODE_TABLE,
};
code/firmware/variants/esp32s3/dreamcatcher/variant.h
+110
View File
@@ -0,0 +1,110 @@
#undef I2C_SDA
#undef I2C_SCL
#define I2C_SDA 16 // I2C pins for this board
#define I2C_SCL 17
#define I2C_SDA1 45
#define I2C_SCL1 46
#define LED_POWER 6
#define LED_STATE_ON 1
#define BUTTON_PIN 0
#define HAS_TPS65233
// V1 of SubG Switch SMA 0 or F Selector 1
// #define RF_SW_SUBG1 8
// V2 of SubG Switch SMA 1 or F Selector 0
// #define RF_SW_SUBG2 5
#define RESET_OLED 8 // Emulate RF_SW_SUBG1, Use F Connector
#define VTFT_CTRL 5 // Emulate RF_SW_SUBG2, for SMA swap the pin values
#if OTHERNET_DC_REV == 2206
#define USE_LR1120
#define SPI_MISO 37
#define SPI_MOSI 39
#define SPI_SCK 38
#define SDCARD_CS 40
#define PIN_BUZZER 48
// These can either be used for GPS or a serial link. Define through Protobufs
// #define GPS_RX_PIN 10
// #define GPS_TX_PIN 21
#define PIN_POWER_EN 7 // RF section power supply enable
#define PERIPHERAL_WARMUP_MS 1000 // wait for TPS chip to initialize
#define TPS_EXTM 45 // connected, but not used
#define BIAS_T_ENABLE 9 // needs to be low
#define BIAS_T_VALUE 0
#else // 2301
#define USE_LR1121
#define SPI_MISO 10
#define SPI_MOSI 39
#define SPI_SCK 38
#define SDCARD_CS 40
// This is only informational, we always use SD cards in 1 bit mode
#define SPI_DATA1 15
#define SPI_DATA2 18
// These can either be used for GPS or a serial link. Define through Protobufs
// #define GPS_RX_PIN 36
// #define GPS_TX_PIN 37
// dac / amp instead of buzzer
#define HAS_I2S
#define DAC_I2S_BCK 21
#define DAC_I2S_WS 9
#define DAC_I2S_DOUT 48
#define DAC_I2S_MCLK 44
#define BIAS_T_ENABLE 7 // needs to be low
#define BIAS_T_VALUE 0
#define BIAS_T_SUBGHZ 2 // also needs to be low, we hijack SENSOR_POWER_CTRL_PIN to emulate this
#define SENSOR_POWER_CTRL_PIN BIAS_T_SUBGHZ
#define SENSOR_POWER_ON 0
#endif
#define HAS_SDCARD // Have SPI interface SD card slot
#define SDCARD_USE_SPI1
#define LORA_RESET 3
#define LORA_SCK 12
#define LORA_MISO 13
#define LORA_MOSI 11
#define LORA_CS 14
#define LORA_DIO9 4
#define LORA_DIO2 47
#define LR1120_IRQ_PIN LORA_DIO9
#define LR1120_NRESET_PIN LORA_RESET
#define LR1120_BUSY_PIN LORA_DIO2
#define LR1120_SPI_NSS_PIN LORA_CS
#define LR1120_SPI_SCK_PIN LORA_SCK
#define LR1120_SPI_MOSI_PIN LORA_MOSI
#define LR1120_SPI_MISO_PIN LORA_MISO
#define LR1121_IRQ_PIN LORA_DIO9
#define LR1121_NRESET_PIN LORA_RESET
#define LR1121_BUSY_PIN LORA_DIO2
#define LR1121_SPI_NSS_PIN LORA_CS
#define LR1121_SPI_SCK_PIN LORA_SCK
#define LR1121_SPI_MOSI_PIN LORA_MOSI
#define LR1121_SPI_MISO_PIN LORA_MISO
#define LR11X0_DIO3_TCXO_VOLTAGE 1.8
#define LR11X0_DIO_AS_RF_SWITCH
// This board needs external switching between sub-GHz and 2.4G circuits
// V1 of RF1 selector SubG 1 or 2.4GHz 0
// #define RF_SW_SMA1 42
// V2 of RF1 Selector SubG 0 or 2.4GHz 1
// #define RF_SW_SMA2 41
#define LR11X0_RF_SWITCH_SUBGHZ 42
#define LR11X0_RF_SWITCH_2_4GHZ 41
code/firmware/variants/esp32s3/elecrow_panel/pins_arduino.h
+58
View File
@@ -0,0 +1,58 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 15;
static const uint8_t SCL = 16;
// Default SPI will be mapped to Radio
static const uint8_t SS = -1;
static const uint8_t MOSI = 48;
static const uint8_t MISO = 47;
static const uint8_t SCK = 41;
static const uint8_t SPI_MOSI = 6;
static const uint8_t SPI_SCK = 5;
static const uint8_t SPI_MISO = 4;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/elecrow_panel/platformio.ini
+166
View File
@@ -0,0 +1,166 @@
[crowpanel_base]
extends = esp32s3_base
board = crowpanel
board_check = true
upload_protocol = esptool
board_build.partitions = default_16MB.csv ; must be here for some reason, board.json is not enough !?
build_flags = ${esp32s3_base.build_flags} -Os
-I variants/esp32s3/elecrow_panel
-D ELECROW_PANEL
-D CONFIG_ARDUHAL_LOG_COLORS
-D RADIOLIB_DEBUG_SPI=0
-D RADIOLIB_DEBUG_PROTOCOL=0
-D RADIOLIB_DEBUG_BASIC=0
-D RADIOLIB_VERBOSE_ASSERT=0
-D RADIOLIB_SPI_PARANOID=0
-D MESHTASTIC_EXCLUDE_CANNEDMESSAGES=1
-D MESHTASTIC_EXCLUDE_INPUTBROKER=1
-D MESHTASTIC_EXCLUDE_WEBSERVER=1
-D MESHTASTIC_EXCLUDE_SERIAL=1
-D MESHTASTIC_EXCLUDE_SOCKETAPI=1
-D MESHTASTIC_EXCLUDE_SCREEN=1
-D CONFIG_DISABLE_HAL_LOCKS=1
-D USE_PIN_BUZZER
-D HAS_SCREEN=0
-D HAS_TFT=1
-D RAM_SIZE=6144
-D LV_LVGL_H_INCLUDE_SIMPLE
-D LV_CONF_INCLUDE_SIMPLE
-D LV_COMP_CONF_INCLUDE_SIMPLE
-D LV_USE_SYSMON=0
-D LV_USE_PROFILER=0
-D LV_USE_PERF_MONITOR=0
-D LV_USE_MEM_MONITOR=0
-D LV_USE_LOG=0
-D LV_BUILD_TEST=0
-D USE_LOG_DEBUG
-D LOG_DEBUG_INC=\"DebugConfiguration.h\"
-D USE_PACKET_API
-D HAS_SDCARD
-D SD_SPI_FREQUENCY=75000000
lib_deps = ${esp32s3_base.lib_deps}
${device-ui_base.lib_deps}
# renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
earlephilhower/ESP8266Audio@1.9.9
# renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
earlephilhower/ESP8266SAM@1.1.0
# renovate: datasource=custom.pio depName=TCA9534 packageName=hideakitai/library/TCA9534
hideakitai/TCA9534@0.1.1
lovyan03/LovyanGFX@1.2.0 ; note: v1.2.7 breaks the elecrow 7" display functionality
[crowpanel_small_esp32s3_base] ; 2.4, 2.8, 3.5 inch
extends = crowpanel_base
build_flags =
${crowpanel_base.build_flags}
-D CROW_SELECT=1
-D SDCARD_USE_SOFT_SPI
-D SDCARD_CS=7
-D SPI_DRIVER_SELECT=2
-D LGFX_DRIVER_TEMPLATE
-D LGFX_DRIVER=LGFX_GENERIC
-D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_GENERIC.h\"
-D VIEW_320x240
-D MAP_FULL_REDRAW
[crowpanel_large_esp32s3_base] ; 4.3, 5.0, 7.0 inch
extends = crowpanel_base
build_flags =
${crowpanel_base.build_flags}
-D CROW_SELECT=2
-D SDCARD_CS=7
-D LGFX_DRIVER=LGFX_ELECROW70
-D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_ELECROW70.h\"
-D DISPLAY_SET_RESOLUTION
[env:elecrow-adv-24-28-tft]
custom_meshtastic_hw_model = 97
custom_meshtastic_hw_model_slug = CROWPANEL
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Crowpanel Adv 2.4/2.8 TFT
custom_meshtastic_images = crowpanel_2_4.svg, crowpanel_2_8.svg
custom_meshtastic_tags = Elecrow
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 16MB
extends = crowpanel_small_esp32s3_base
build_flags =
${crowpanel_small_esp32s3_base.build_flags}
-D SPI_FREQUENCY=80000000
-D LGFX_SCREEN_WIDTH=240
-D LGFX_SCREEN_HEIGHT=320
-D DISPLAY_SIZE=320x240 ; landscape mode
-D LGFX_PANEL=ST7789
-D LGFX_ROTATION=1
-D LGFX_CFG_HOST=SPI2_HOST
-D LGFX_PIN_SCK=42
-D LGFX_PIN_MOSI=39
-D LGFX_PIN_DC=41
-D LGFX_PIN_CS=40
-D LGFX_PIN_BL=38
-D LGFX_TOUCH=FT5x06
-D LGFX_TOUCH_I2C_ADDR=0x38
-D LGFX_TOUCH_I2C_SDA=15
-D LGFX_TOUCH_I2C_SCL=16
-D LGFX_TOUCH_INT=47
-D LGFX_TOUCH_RST=48
-D LGFX_TOUCH_ROTATION=0
[env:elecrow-adv-35-tft]
custom_meshtastic_hw_model = 97
custom_meshtastic_hw_model_slug = CROWPANEL
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Crowpanel Adv 3.5 TFT
custom_meshtastic_images = crowpanel_3_5.svg
custom_meshtastic_tags = Elecrow
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 16MB
extends = crowpanel_small_esp32s3_base
board_level = pr
build_flags =
${crowpanel_small_esp32s3_base.build_flags}
-D LV_CACHE_DEF_SIZE=2097152
-D SPI_FREQUENCY=60000000
-D LGFX_SCREEN_WIDTH=320
-D LGFX_SCREEN_HEIGHT=480
-D DISPLAY_SIZE=320x480 ; portrait mode
-D LGFX_PANEL=ILI9488
-D LGFX_ROTATION=0
-D LGFX_CFG_HOST=SPI2_HOST
-D LGFX_PIN_SCK=42
-D LGFX_PIN_MOSI=39
-D LGFX_PIN_DC=41
-D LGFX_PIN_CS=40
-D LGFX_PIN_BL=38
-D LGFX_TOUCH=GT911
-D LGFX_TOUCH_I2C_ADDR=0x5D
-D LGFX_TOUCH_I2C_SDA=15
-D LGFX_TOUCH_I2C_SCL=16
-D LGFX_TOUCH_INT=47
-D LGFX_TOUCH_RST=48
-D LGFX_TOUCH_ROTATION=0
-D DISPLAY_SET_RESOLUTION
; 4.3, 5.0, 7.0 inch 800x480 IPS (V1)
[env:elecrow-adv1-43-50-70-tft]
custom_meshtastic_hw_model = 97
custom_meshtastic_hw_model_slug = CROWPANEL
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Crowpanel Adv 4.3/5.0/7.0 TFT
custom_meshtastic_images = crowpanel_5_0.svg, crowpanel_7_0.svg
custom_meshtastic_tags = Elecrow
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 16MB
extends = crowpanel_large_esp32s3_base
build_flags =
${crowpanel_large_esp32s3_base.build_flags}
-D VIEW_320x240
-D DISPLAY_SIZE=800x480 ; landscape mode
code/firmware/variants/esp32s3/elecrow_panel/variant.h
+90
View File
@@ -0,0 +1,90 @@
#define I2C_SDA 15
#define I2C_SCL 16
#if CROW_SELECT == 1
#define WAKE_ON_TOUCH
#define SCREEN_TOUCH_INT 47
#define USE_POWERSAVE
#define SLEEP_TIME 180
#endif
#if CROW_SELECT == 1
// dac / amp
// #define HAS_I2S // didn't get I2S sound working
#define PIN_BUZZER 8 // using pwm buzzer instead (nobody will notice, lol)
#define DAC_I2S_BCK 13
#define DAC_I2S_WS 11
#define DAC_I2S_DOUT 12
#define DAC_I2S_MCLK 8 // don't use GPIO0 because it's assigned to LoRa or button
#else
#define PIN_BUZZER 8
#endif
// GPS via UART1 connector
#define GPS_DEFAULT_NOT_PRESENT 1
#define HAS_GPS 1
#if CROW_SELECT == 1
#define GPS_RX_PIN 18
#define GPS_TX_PIN 17
#else
// GPIOs shared with LoRa or MIC module
#define GPS_RX_PIN 19
#define GPS_TX_PIN 20
#endif
// Extension Slot Layout, viewed from above (2.4-3.5)
// DIO1/IO1 o o IO2/NRESET
// SCK/IO10 o o IO16/NC
// MISO/IO9 o o IO15/NC
// MOSI/IO3 o o NC/DIO2
// 3V3 o o IO46/BUSY
// GND o o IO0/NSS
// 5V/NC o o NC/DIO3
// J9 J8
// Extension Slot Layout, viewed from above (4.3-7.0)
// !! DIO1/IO20 o o IO19/NRESET !!
// !! SCK/IO5 o o IO16/NC
// !! MISO/IO4 o o IO15/NC
// !! MOSI/IO6 o o NC/DIO2
// 3V3 o o IO2/BUSY !!
// GND o o IO0/NSS
// 5V/NC o o NC/DIO3
// J9 J8
// LoRa
#define USE_SX1262
#if CROW_SELECT == 1
// 2.4", 2.8, 3.5"""
#define HW_SPI1_DEVICE
#define LORA_CS 0
#define LORA_SCK 10
#define LORA_MISO 9
#define LORA_MOSI 3
#define LORA_RESET 2
#define LORA_DIO1 1 // SX1262 IRQ
#define LORA_DIO2 46 // SX1262 BUSY
// need to pull IO45 low to enable LORA and disable Microphone on 24 28 35
#define SENSOR_POWER_CTRL_PIN 45
#define SENSOR_POWER_ON LOW
#else
// 4.3", 5.0", 7.0"
#define LORA_CS 0
#define LORA_SCK 5
#define LORA_MISO 4
#define LORA_MOSI 6
#define LORA_RESET 19
#define LORA_DIO1 20 // SX1262 IRQ
#define LORA_DIO2 2 // SX1262 BUSY
#endif
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 3.3
code/firmware/variants/esp32s3/esp32-s3-pico/pins_arduino.h
+28
View File
@@ -0,0 +1,28 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// The default Wire will be mapped to PMU and RTC
static const uint8_t SDA = 15;
static const uint8_t SCL = 16;
// Default SPI will be mapped to Radio
static const uint8_t MISO = 37;
static const uint8_t SCK = 35;
static const uint8_t MOSI = 36;
static const uint8_t SS = 14;
static const uint8_t BAT_ADC_PIN = 26;
// #define SPI_MOSI (11)
// #define SPI_SCK (14)
// #define SPI_MISO (2)
// #define SPI_CS (13)
// #define SDCARD_CS SPI_CS
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/esp32-s3-pico/platformio.ini
+28
View File
@@ -0,0 +1,28 @@
[env:ESP32-S3-Pico]
board_level = extra
extends = esp32s3_base
upload_protocol = esptool
board = esp32-s3-pico
board_build.partitions = default_16MB.csv
board_upload.use_1200bps_touch = yes
board_upload.wait_for_upload_port = yes
board_upload.require_upload_port = yes
;upload_port = /dev/ttyACM0
build_flags = ${esp32s3_base.build_flags}
-DESP32_S3_PICO
;-DPRIVATE_HW
-Ivariants/esp32s3/esp32-s3-pico
-DBOARD_HAS_PSRAM
-DEINK_DISPLAY_MODEL=GxEPD2_290_T94_V2
-DEINK_WIDTH=296
-DEINK_HEIGHT=128
lib_deps = ${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
zinggjm/GxEPD2@1.6.7
# renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
adafruit/Adafruit NeoPixel@1.15.4
code/firmware/variants/esp32s3/esp32-s3-pico/variant.h
+80
View File
@@ -0,0 +1,80 @@
/*
*/
#define HAS_GPS 0
#undef GPS_RX_PIN
#undef GPS_TX_PIN
#define EXT_NOTIFY_OUT 22
#define BUTTON_PIN 0 // 17
// Board has RGB LED 21
#define HAS_NEOPIXEL // Enable the use of neopixels
#define NEOPIXEL_COUNT 1 // How many neopixels are connected
#define NEOPIXEL_DATA 21 // gpio pin used to send data to the neopixels
#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
// The usbPower state is revered ?
// DEBUG | ??:??:?? 365 [Power] Battery: usbPower=0, isCharging=0, batMv=4116, batPct=90
// DEBUG | ??:??:?? 385 [Power] Battery: usbPower=1, isCharging=1, batMv=4243, batPct=0
// https://www.waveshare.com/img/devkit/ESP32-S3-Pico/ESP32-S3-Pico-details-inter-1.jpg
// digram is incorrect labeled as battery pin is getting readings on GPIO7_CH1?
#define BATTERY_PIN 7
#define ADC_CHANNEL ADC1_GPIO7_CHANNEL
// #define ADC_CHANNEL ADC1_GPIO6_CHANNEL
// ratio of voltage divider = 3.0 (R17=200k, R18=100k)
#define ADC_MULTIPLIER 3.1 // 3.0 + a bit for being optimistic
#define I2C_SDA 15
#define I2C_SCL 16
// Enable secondary bus for external periherals
// https://www.waveshare.com/wiki/Pico-OLED-1.3
// #define USE_SH1107_128_64
// Not working
#define I2C_SDA1 17
#define I2C_SCL1 18
#define BUTTON_PIN 0 // This is the BOOT button
#define BUTTON_NEED_PULLUP
// #define USE_RF95 // RFM95/SX127x
#define USE_SX1262
// #define USE_SX1280
#define LORA_MISO 37
#define LORA_SCK 35
#define LORA_MOSI 36
#define LORA_CS 14
#define LORA_RESET 40
#define LORA_DIO1 4
#define LORA_DIO2 13
#ifdef USE_SX1262
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#endif
#ifdef USE_SX1280
#define SX128X_CS LORA_CS
#define SX128X_DIO1 LORA_DIO1
#define SX128X_BUSY 9
#define SX128X_RESET LORA_RESET
#endif
#define USE_EINK
/*
* eink display pins
*/
#define PIN_EINK_CS 34
#define PIN_EINK_BUSY 38
#define PIN_EINK_DC 33
#define PIN_EINK_RES 42 // 37 //(-1) // cant be MISO Waveshare ??)
#define PIN_EINK_SCLK 35
#define PIN_EINK_MOSI 36
code/firmware/variants/esp32s3/esp32s3.ini
+10
View File
@@ -0,0 +1,10 @@
[esp32s3_base]
extends = esp32_common
custom_esp32_kind = esp32s3
monitor_speed = 115200
lib_deps =
${esp32_common.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-ESP32_Codec2 packageName=https://github.com/meshtastic/ESP32_Codec2 gitBranch=master
https://github.com/meshtastic/ESP32_Codec2/archive/633326c78ac251c059ab3a8c430fcdf25b41672f.zip
code/firmware/variants/esp32s3/hackaday-communicator/pins_arduino.h
+59
View File
@@ -0,0 +1,59 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// static const uint8_t TX = 43;
// static const uint8_t RX = 44;
static const uint8_t SDA = 47;
static const uint8_t SCL = 14;
// Default SPI will be mapped to Radio
static const uint8_t SS = 17;
static const uint8_t MOSI = 3;
static const uint8_t MISO = 9;
static const uint8_t SCK = 8;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
// static const uint8_t BAT_ADC_PIN = 4;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/hackaday-communicator/platformio.ini
+20
View File
@@ -0,0 +1,20 @@
; Hackaday Communicator
[env:hackaday-communicator]
extends = esp32s3_base
board = hackaday-communicator
board_check = true
board_build.partitions = default_16MB.csv
upload_protocol = esptool
build_src_filter =
${esp32s3_base.build_src_filter}
+<../variants/esp32s3/hackaday-communicator>
build_flags = ${esp32s3_base.build_flags}
-D HACKADAY_COMMUNICATOR
-D BOARD_HAS_PSRAM
-I variants/esp32s3/hackaday-communicator
lib_deps = ${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-Arduino_GFX packageName=https://github.com/meshtastic/Arduino_GFX gitBranch=master
https://github.com/meshtastic/Arduino_GFX/archive/054e81ffaf23784830a734e3c184346789349406.zip
code/firmware/variants/esp32s3/hackaday-communicator/variant.cpp
+6
View File
@@ -0,0 +1,6 @@
#include "variant.h"
#include "Arduino.h"
void earlyInitVariant()
{
pinMode(KB_INT, INPUT);
}
code/firmware/variants/esp32s3/hackaday-communicator/variant.h
+50
View File
@@ -0,0 +1,50 @@
#define TFT_BL 2
#define SPI_FREQUENCY 2000000
#define SPI_READ_FREQUENCY 16000000
#define TFT_HEIGHT 142
#define TFT_WIDTH 428
#define TFT_OFFSET_X 0
#define TFT_OFFSET_Y 0
#define TFT_OFFSET_ROTATION 0
#define SCREEN_TRANSITION_FRAMERATE 5
#define HAS_SCREEN 1
#define TFT_BLACK 0
#define BRIGHTNESS_DEFAULT 130 // Medium Low Brightness
#define USE_TFTDISPLAY 1
#define USE_POWERSAVE
#define SLEEP_TIME 120
#define GPS_DEFAULT_NOT_PRESENT 1
// keyboard
#define I2C_SDA 47 // I2C pins for this board
#define I2C_SCL 14
// #define KB_BL_PIN 46 // not used for now
#define KB_INT 13
#define TFT_DC 39
#define TFT_CS 41
// LoRa
#define USE_SX1262
#define LORA_SCK 8
#define LORA_MISO 9
#define LORA_MOSI 3
#define LORA_CS 17
#define LORA_RESET 18
#define LORA_DIO1 16 // SX1262 IRQ
#define LORA_DIO2 15 // SX1262 BUSY
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#define LED_NOTIFICATION 1
#define LED_STATE_ON 0
code/firmware/variants/esp32s3/heltec_capsule_sensor_v3/platformio.ini
+10
View File
@@ -0,0 +1,10 @@
[env:heltec_capsule_sensor_v3]
extends = esp32s3_base
board = heltec_wifi_lora_32_V3
board_check = true
board_build.partitions = default_8MB.csv
build_flags =
${esp32s3_base.build_flags} -I variants/esp32s3/heltec_capsule_sensor_v3
-D HELTEC_CAPSULE_SENSOR_V3
-ULED_BUILTIN
;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
code/firmware/variants/esp32s3/heltec_capsule_sensor_v3/variant.h
+55
View File
@@ -0,0 +1,55 @@
#define LED_POWER 33
#define LED_POWER2 34
#define EXT_PWR_DETECT 35
#define BUTTON_PIN 18
#define BUTTON_ACTIVE_LOW false
#define BUTTON_ACTIVE_PULLUP false
#define BATTERY_PIN 7 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO7_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER (4.9 * 1.045)
#define ADC_CTRL 36 // active HIGH, powers the voltage divider. Only on 1.1
#define ADC_CTRL_ENABLED HIGH
#undef GPS_RX_PIN
#undef GPS_TX_PIN
#define GPS_RX_PIN 5
#define GPS_TX_PIN 4
#define PIN_GPS_RESET 3
#define GPS_RESET_MODE LOW
#define PIN_GPS_PPS 1
#define PIN_GPS_EN 21
#define GPS_EN_ACTIVE HIGH
#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#define I2C_SDA 1
#define I2C_SCL 2
#define HAS_SCREEN 0
#define SENSOR_POWER_CTRL_PIN 21
#define SENSOR_POWER_ON 1
#define PERIPHERAL_WARMUP_MS 100
#define SENSOR_GPS_CONFLICT
#define ESP32S3_WAKE_TYPE ESP_EXT1_WAKEUP_ANY_HIGH
code/firmware/variants/esp32s3/heltec_sensor_hub/platformio.ini
+14
View File
@@ -0,0 +1,14 @@
[env:heltec_sensor_hub]
extends = esp32s3_base
board = heltec_wifi_lora_32_V3
board_check = true
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/heltec_sensor_hub
-D HELTEC_SENSOR_HUB
-ULED_BUILTIN
lib_deps = ${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
adafruit/Adafruit NeoPixel@1.15.4
code/firmware/variants/esp32s3/heltec_sensor_hub/variant.h
+48
View File
@@ -0,0 +1,48 @@
#define EXT_PWR_DETECT 20
#define BUTTON_PIN 17
#define BUTTON_ACTIVE_LOW false
#define BUTTON_ACTIVE_PULLUP false
#define BATTERY_PIN 7 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO7_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER (4.9 * 1.045)
#define ADC_CTRL 34 // active HIGH, powers the voltage divider. Only on 1.1
#define ADC_CTRL_ENABLED HIGH
#define HAS_NEOPIXEL // Enable the use of neopixels
#define NEOPIXEL_COUNT 1 // How many neopixels are connected
#define NEOPIXEL_DATA 18 // gpio pin used to send data to the neopixels
#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
#define USE_SX1262
#define LORA_DIO0 RADIOLIB_NC
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#define I2C_SDA 1
#define I2C_SCL 2
#define HAS_SCREEN 0
#define SENSOR_POWER_CTRL_PIN 33
#define SENSOR_POWER_ON 1
#define PERIPHERAL_WARMUP_MS 100
#define ESP32S3_WAKE_TYPE ESP_EXT1_WAKEUP_ANY_HIGH
#define ENVIRONMENTAL_TELEMETRY_MODULE_ENABLE 1
code/firmware/variants/esp32s3/heltec_v3/platformio.ini
+21
View File
@@ -0,0 +1,21 @@
[env:heltec-v3]
custom_meshtastic_hw_model = 43
custom_meshtastic_hw_model_slug = HELTEC_V3
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec V3
custom_meshtastic_images = heltec-v3.svg, heltec-v3-case.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board = heltec_wifi_lora_32_V3
board_level = pr
board_check = true
board_build.partitions = default_8MB.csv
build_flags =
${esp32s3_base.build_flags}
-D HELTEC_V3
-I variants/esp32s3/heltec_v3
-ULED_BUILTIN
code/firmware/variants/esp32s3/heltec_v3/variant.h
+44
View File
@@ -0,0 +1,44 @@
#define LED_POWER LED
#define USE_SSD1306 // Heltec_v3 has a SSD1306 display
#define RESET_OLED RST_OLED
#define I2C_SDA SDA_OLED // I2C pins for this board
#define I2C_SCL SCL_OLED
// Enable secondary bus for external periherals
#define I2C_SDA1 SDA
#define I2C_SCL1 SCL
#define VEXT_ENABLE Vext // active low, powers the oled display and the lora antenna boost
#define BUTTON_PIN 0
#define ADC_CTRL 37
#define ADC_CTRL_ENABLED LOW
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER 4.9 * 1.045
#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#define HAS_32768HZ 1
code/firmware/variants/esp32s3/heltec_v4/pins_arduino.h
+66
View File
@@ -0,0 +1,66 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 4;
static const uint8_t SCL = 3;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t Vext = 36;
static const uint8_t LED = 35;
static const uint8_t RST_OLED = 21;
static const uint8_t SCL_OLED = 18;
static const uint8_t SDA_OLED = 17;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO0 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_v4/platformio.ini
+131
View File
@@ -0,0 +1,131 @@
[heltec_v4_base]
extends = esp32s3_base
board = heltec_v4
board_check = true
board_build.partitions = default_16MB.csv
build_flags =
${esp32s3_base.build_flags}
-D HELTEC_V4
-I variants/esp32s3/heltec_v4
[env:heltec-v4]
custom_meshtastic_hw_model = 110
custom_meshtastic_hw_model_slug = HELTEC_V4
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec V4
custom_meshtastic_images = heltec_v4.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 16MB
extends = heltec_v4_base
build_flags =
${heltec_v4_base.build_flags}
-D HELTEC_V4_OLED
-D USE_SSD1306 ; Heltec_v4 has an SSD1315 display (compatible with SSD1306 driver)
-D LED_POWER=35
-D RESET_OLED=21
-D I2C_SDA=17
-D I2C_SCL=18
-D I2C_SDA1=4
-D I2C_SCL1=3
[env:heltec-v4-tft]
custom_meshtastic_hw_model = 110
custom_meshtastic_hw_model_slug = HELTEC_V4
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec V4 TFT
custom_meshtastic_images = heltec_v4.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 16MB
extends = heltec_v4_base
build_flags =
${heltec_v4_base.build_flags} ;-Os
-D HELTEC_V4_TFT
-D I2C_SDA=4
-D I2C_SCL=3
-D I2C_SDA1=47
-D I2C_SCL1=48
-D PIN_BUTTON2=35
-D PIN_BUZZER=6
-D USE_PIN_BUZZER=PIN_BUZZER
-D CONFIG_ARDUHAL_LOG_COLORS
-D RADIOLIB_DEBUG_SPI=0
-D RADIOLIB_DEBUG_PROTOCOL=0
-D RADIOLIB_DEBUG_BASIC=0
-D RADIOLIB_VERBOSE_ASSERT=0
-D RADIOLIB_SPI_PARANOID=0
-D CONFIG_DISABLE_HAL_LOCKS=1
-D INPUTDRIVER_BUTTON_TYPE=0
-D HAS_SCREEN=1
-D HAS_TFT=1
-D RAM_SIZE=1560
-D LV_LVGL_H_INCLUDE_SIMPLE
-D LV_CONF_INCLUDE_SIMPLE
-D LV_COMP_CONF_INCLUDE_SIMPLE
-D LV_USE_SYSMON=0
-D LV_USE_PROFILER=0
-D LV_USE_PERF_MONITOR=0
-D LV_USE_MEM_MONITOR=0
-D LV_USE_LOG=0
-D LV_BUILD_TEST=0
-D USE_LOG_DEBUG
-D LOG_DEBUG_INC=\"DebugConfiguration.h\"
-D USE_PACKET_API
-D LGFX_DRIVER=LGFX_HELTEC_V4_TFT
-D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_HELTEC_V4_TFT.h\"
-D VIEW_320x240
-D MAP_FULL_REDRAW
-D DISPLAY_SIZE=320x240 ; landscape mode
-D LGFX_PIN_SCK=17
-D LGFX_PIN_MOSI=33
-D LGFX_PIN_DC=16
-D LGFX_PIN_CS=15
-D LGFX_PIN_BL=21
-D LGFX_PIN_RST=18
-D CUSTOM_TOUCH_DRIVER
-D TOUCH_SDA_PIN=I2C_SDA1
-D TOUCH_SCL_PIN=I2C_SCL1
-D TOUCH_INT_PIN=-1 ;45
-D TOUCH_RST_PIN=44
;base UI
-D TFT_CS=LGFX_PIN_CS
-D ST7789_CS=TFT_CS
-D ST7789_RS=LGFX_PIN_DC
-D ST7789_SDA=LGFX_PIN_MOSI
-D ST7789_SCK=LGFX_PIN_SCK
-D ST7789_RESET=LGFX_PIN_RST
-D ST7789_MISO=-1
-D ST7789_BUSY=-1
-D ST7789_BL=LGFX_PIN_BL
-D ST7789_SPI_HOST=SPI3_HOST
-D TFT_BL=ST7789_BL
-D SPI_FREQUENCY=40000000
-D SPI_READ_FREQUENCY=4000000
-D TFT_HEIGHT=320
-D TFT_WIDTH=240
-D TFT_OFFSET_X=0
-D TFT_OFFSET_Y=0
-D TFT_OFFSET_ROTATION=0
-D SCREEN_ROTATE
-D SCREEN_TRANSITION_FRAMERATE=5
-D BRIGHTNESS_DEFAULT=130 ; Medium Low Brightness
-D HAS_TOUCHSCREEN=1
-D TOUCH_I2C_PORT=0
-D TOUCH_SLAVE_ADDRESS=0x2E
-D SCREEN_TOUCH_INT=TOUCH_INT_PIN
-D SCREEN_TOUCH_RST=TOUCH_RST_PIN
lib_deps = ${heltec_v4_base.lib_deps}
${device-ui_base.lib_deps}
# renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
lovyan03/LovyanGFX@1.2.19
# renovate: datasource=git-refs depName=Quency-D_chsc6x packageName=https://github.com/Quency-D/chsc6x gitBranch=master
https://github.com/Quency-D/chsc6x/archive/5cbead829d6b432a8d621ed1aafd4eb474fd4f27.zip
code/firmware/variants/esp32s3/heltec_v4/variant.h
+76
View File
@@ -0,0 +1,76 @@
#define VEXT_ENABLE 36 // active low, powers the oled display and the lora antenna boost
#define BUTTON_PIN 0
#define ADC_CTRL 37
#define ADC_CTRL_ENABLED HIGH
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER 4.9 * 1.045
#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TCXO is enabled
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
// ---- GC1109 RF FRONT END CONFIGURATION ----
// The Heltec V4 uses a GC1109 FEM chip with integrated PA and LNA
// RF path: SX1262 -> GC1109 PA -> Pi attenuator -> Antenna
// Measured net TX gain (non-linear due to PA compression):
// +11dB at 0-15dBm input (e.g., 10dBm in -> 21dBm out)
// +10dB at 16-17dBm input
// +9dB at 18-19dBm input
// +7dB at 21dBm input (e.g., 21dBm in -> 28dBm out max)
// Control logic (from GC1109 datasheet):
// Shutdown: CSD=0, CTX=X, CPS=X
// Receive LNA: CSD=1, CTX=0, CPS=X (17dB gain, 2dB NF)
// Transmit bypass: CSD=1, CTX=1, CPS=0 (~1dB loss, no PA)
// Transmit PA: CSD=1, CTX=1, CPS=1 (full PA enabled)
// Pin mapping:
// CTX (pin 6) -> SX1262 DIO2: TX/RX path select (automatic via SX126X_DIO2_AS_RF_SWITCH)
// CSD (pin 4) -> GPIO2: Chip enable (HIGH=on, LOW=shutdown)
// CPS (pin 5) -> GPIO46: PA mode select (HIGH=full PA, LOW=bypass)
// VCC0/VCC1 -> Vfem via U3 LDO, controlled by GPIO7
#define USE_GC1109_PA
#define LORA_PA_POWER 7 // VFEM_Ctrl - GC1109 LDO power enable
#define LORA_PA_EN 2 // CSD - GC1109 chip enable (HIGH=on)
#define LORA_PA_TX_EN 46 // CPS - GC1109 PA mode (HIGH=full PA, LOW=bypass)
// GC1109 FEM: TX/RX path switching is handled by DIO2 -> CTX pin (via SX126X_DIO2_AS_RF_SWITCH)
// GPIO46 is CPS (PA mode), not TX control - setTransmitEnable() handles it in SX126xInterface.cpp
// Do NOT use SX126X_TXEN/RXEN as that would cause double-control of GPIO46
#if HAS_TFT
#define USE_TFTDISPLAY 1
#endif
/*
* GPS pins
*/
#define GPS_L76K
#define PIN_GPS_RESET (42) // An output to reset L76K GPS. As per datasheet, low for > 100ms will reset the L76K
#define GPS_RESET_MODE LOW
#define PIN_GPS_EN (34)
#define GPS_EN_ACTIVE LOW
#define PERIPHERAL_WARMUP_MS 1000 // Make sure I2C QuickLink has stable power before continuing
#define PIN_GPS_STANDBY (40) // An output to wake GPS, low means allow sleep, high means force wake
#define PIN_GPS_PPS (41)
// Seems to be missing on this new board
#define GPS_TX_PIN (38) // This is for bits going TOWARDS the CPU
#define GPS_RX_PIN (39) // This is for bits going TOWARDS the GPS
#define GPS_THREAD_INTERVAL 50
code/firmware/variants/esp32s3/heltec_vision_master_e213/einkDetect.h
+35
View File
@@ -0,0 +1,35 @@
#pragma once
#include "configuration.h"
enum class EInkDetectionResult : uint8_t {
LCMEN213EFC1 = 0, // Initial version
E0213A367 = 1, // E213 PCB marked V1.1 (Mid 2025)
};
EInkDetectionResult detectEInk()
{
// Test 1: Logic of BUSY pin
// Determines controller IC manufacturer
// Fitipower: busy when LOW
// Solomon Systech: busy when HIGH
// Force display BUSY by holding reset pin active
pinMode(PIN_EINK_RES, OUTPUT);
digitalWrite(PIN_EINK_RES, LOW);
delay(10);
// Read whether pin is HIGH or LOW while busy
pinMode(PIN_EINK_BUSY, INPUT);
bool busyLogic = digitalRead(PIN_EINK_BUSY);
// Test complete. Release pin
pinMode(PIN_EINK_RES, INPUT);
if (busyLogic == LOW)
return EInkDetectionResult::LCMEN213EFC1;
else // busy HIGH
return EInkDetectionResult::E0213A367;
}
code/firmware/variants/esp32s3/heltec_vision_master_e213/nicheGraphics.h
+119
View File
@@ -0,0 +1,119 @@
#pragma once
#include "configuration.h"
#ifdef MESHTASTIC_INCLUDE_NICHE_GRAPHICS
// InkHUD-specific components
// ---------------------------
#include "graphics/niche/InkHUD/InkHUD.h"
// Applets
#include "graphics/niche/InkHUD/Applets/User/AllMessage/AllMessageApplet.h"
#include "graphics/niche/InkHUD/Applets/User/DM/DMApplet.h"
#include "graphics/niche/InkHUD/Applets/User/FavoritesMap/FavoritesMapApplet.h"
#include "graphics/niche/InkHUD/Applets/User/Heard/HeardApplet.h"
#include "graphics/niche/InkHUD/Applets/User/Positions/PositionsApplet.h"
#include "graphics/niche/InkHUD/Applets/User/RecentsList/RecentsListApplet.h"
#include "graphics/niche/InkHUD/Applets/User/ThreadedMessage/ThreadedMessageApplet.h"
// Shared NicheGraphics components
// --------------------------------
#include "graphics/niche/Drivers/EInk/E0213A367.h"
#include "graphics/niche/Drivers/EInk/LCMEN2R13EFC1.h"
#include "graphics/niche/Inputs/TwoButton.h"
#include "buzz.h" // Button feedback
#include "einkDetect.h" // Detect display model at runtime
void setupNicheGraphics()
{
using namespace NicheGraphics;
// Detect E-Ink Model
// -------------------
EInkDetectionResult displayModel = detectEInk();
// SPI
// -----------------------------
// Display is connected to HSPI
SPIClass *hspi = new SPIClass(HSPI);
hspi->begin(PIN_EINK_SCLK, -1, PIN_EINK_MOSI, PIN_EINK_CS);
// E-Ink Driver
// -----------------------------
Drivers::EInk *driver;
if (displayModel == EInkDetectionResult::LCMEN213EFC1) // V1 (unmarked)
driver = new Drivers::LCMEN213EFC1;
else if (displayModel == EInkDetectionResult::E0213A367) // V1.1
driver = new Drivers::E0213A367;
driver->begin(hspi, PIN_EINK_DC, PIN_EINK_CS, PIN_EINK_BUSY, PIN_EINK_RES);
// InkHUD
// ----------------------------
InkHUD::InkHUD *inkhud = InkHUD::InkHUD::getInstance();
// Set the E-Ink driver
inkhud->setDriver(driver);
// Set how many FAST updates per FULL update
// Set how unhealthy additional FAST updates beyond this number are
if (displayModel == EInkDetectionResult::LCMEN213EFC1) // V1 (unmarked)
inkhud->setDisplayResilience(10, 1.5);
else if (displayModel == EInkDetectionResult::E0213A367) // V1.1
inkhud->setDisplayResilience(15, 3);
// Select fonts
InkHUD::Applet::fontLarge = FREESANS_12PT_WIN1252;
InkHUD::Applet::fontMedium = FREESANS_9PT_WIN1252;
InkHUD::Applet::fontSmall = FREESANS_6PT_WIN1252;
// Customize default settings
inkhud->persistence->settings.userTiles.maxCount = 2; // How many tiles can the display handle?
inkhud->persistence->settings.rotation = 3; // 270 degrees clockwise
inkhud->persistence->settings.userTiles.count = 1; // One tile only by default, keep things simple for new users
inkhud->persistence->settings.optionalMenuItems.nextTile = false; // Behavior handled by aux button instead
// Pick applets
// Note: order of applets determines priority of "auto-show" feature
inkhud->addApplet("All Messages", new InkHUD::AllMessageApplet, true, true); // Activated, autoshown
inkhud->addApplet("DMs", new InkHUD::DMApplet); // -
inkhud->addApplet("Channel 0", new InkHUD::ThreadedMessageApplet(0)); // -
inkhud->addApplet("Channel 1", new InkHUD::ThreadedMessageApplet(1)); // -
inkhud->addApplet("Positions", new InkHUD::PositionsApplet, true); // Activated
inkhud->addApplet("Favorites Map", new InkHUD::FavoritesMapApplet); // -
inkhud->addApplet("Recents List", new InkHUD::RecentsListApplet); // -
inkhud->addApplet("Heard", new InkHUD::HeardApplet, true, false, 0); // Activated, not autoshown, default on tile 0
// Start running InkHUD
inkhud->begin();
// Buttons
// --------------------------
Inputs::TwoButton *buttons = Inputs::TwoButton::getInstance(); // Shared NicheGraphics component
// #0: Main User Button
buttons->setWiring(0, Inputs::TwoButton::getUserButtonPin());
buttons->setHandlerShortPress(0, [inkhud]() { inkhud->shortpress(); });
buttons->setHandlerLongPress(0, [inkhud]() { inkhud->longpress(); });
// #1: Aux Button
buttons->setWiring(1, PIN_BUTTON2);
buttons->setHandlerShortPress(1, [inkhud]() {
inkhud->nextTile();
playChirp();
});
// Begin handling button events
buttons->start();
}
#endif
code/firmware/variants/esp32s3/heltec_vision_master_e213/pins_arduino.h
+57
View File
@@ -0,0 +1,57 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 39;
static const uint8_t SCL = 38;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO1 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_vision_master_e213/platformio.ini
+51
View File
@@ -0,0 +1,51 @@
[env:heltec-vision-master-e213]
custom_meshtastic_hw_model = 67
custom_meshtastic_hw_model_slug = HELTEC_VISION_MASTER_E213
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec Vision Master E213
custom_meshtastic_images = heltec-vision-master-e213.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board = heltec_vision_master_e213
board_build.partitions = default_8MB.csv
build_flags =
${esp32s3_base.build_flags}
-Ivariants/esp32s3/heltec_vision_master_e213
-DHELTEC_VISION_MASTER_E213
-DUSE_EINK
-DGXEPD2_DRIVER_0=GxEPD2_213_FC1
-DGXEPD2_DRIVER_1=GxEPD2_213_E0213A367
-DEINK_WIDTH=250
-DEINK_HEIGHT=122
-DUSE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
-DEINK_LIMIT_FASTREFRESH=10 ; How many consecutive fast-refreshes are permitted
-DEINK_BACKGROUND_USES_FAST ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
-DEINK_HASQUIRK_GHOSTING ; Display model is identified as "prone to ghosting"
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
upload_speed = 115200
[env:heltec-vision-master-e213-inkhud]
extends = esp32s3_base, inkhud
board = heltec_vision_master_e213
board_level = pr
board_build.partitions = default_8MB.csv
build_src_filter =
${esp32s3_base.build_src_filter}
${inkhud.build_src_filter}
build_flags =
${esp32s3_base.build_flags}
${inkhud.build_flags}
-I variants/esp32s3/heltec_vision_master_e213
-D HELTEC_VISION_MASTER_E213
lib_deps =
${inkhud.lib_deps} ; InkHUD libs first, so we get GFXRoot instead of AdafruitGFX
${esp32s3_base.lib_deps}
upload_speed = 921600
code/firmware/variants/esp32s3/heltec_vision_master_e213/variant.h
+54
View File
@@ -0,0 +1,54 @@
#define LED_POWER 45 // LED is not populated on earliest board variant
#define BUTTON_PIN 0
#define PIN_BUTTON2 21 // Second built-in button
#define ALT_BUTTON_PIN PIN_BUTTON2 // Send the up event
// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL
// Display (E-Ink)
#define PIN_EINK_CS 5
#define PIN_EINK_BUSY 1
#define PIN_EINK_DC 2
#define PIN_EINK_RES 3
#define PIN_EINK_SCLK 4
#define PIN_EINK_MOSI 6
// SPI
#define SPI_INTERFACES_COUNT 2
#define PIN_SPI_MISO 11
#define PIN_SPI_MOSI 10
#define PIN_SPI_SCK 9
// Power
#define VEXT_ENABLE 18 // Powers the E-Ink display, and the 3.3V supply to the I2C QuickLink connector
#define PERIPHERAL_WARMUP_MS 1000 // Make sure I2C QuickLink has stable power before continuing
#define VEXT_ON_VALUE HIGH
#define ADC_CTRL 46
#define ADC_CTRL_ENABLED HIGH
#define BATTERY_PIN 7
#define ADC_CHANNEL ADC1_GPIO7_CHANNEL
#define ADC_MULTIPLIER 4.9 * 1.03
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5
// LoRa
#define USE_SX1262
#define LORA_DIO0 RADIOLIB_NC // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
code/firmware/variants/esp32s3/heltec_vision_master_e290/nicheGraphics.h
+116
View File
@@ -0,0 +1,116 @@
/*
Most of the Meshtastic firmware uses preprocessor macros throughout the code to support different hardware variants.
NicheGraphics attempts a different approach:
Per-device config takes place in this setupNicheGraphics() method
(And a small amount in platformio.ini)
This file sets up InkHUD for Heltec VM-E290.
Different NicheGraphics UIs and different hardware variants will each have their own setup procedure.
*/
#pragma once
#include "configuration.h"
#ifdef MESHTASTIC_INCLUDE_NICHE_GRAPHICS
// InkHUD-specific components
// ---------------------------
#include "graphics/niche/InkHUD/InkHUD.h"
// Applets
#include "graphics/niche/InkHUD/Applets/User/AllMessage/AllMessageApplet.h"
#include "graphics/niche/InkHUD/Applets/User/DM/DMApplet.h"
#include "graphics/niche/InkHUD/Applets/User/FavoritesMap/FavoritesMapApplet.h"
#include "graphics/niche/InkHUD/Applets/User/Heard/HeardApplet.h"
#include "graphics/niche/InkHUD/Applets/User/Positions/PositionsApplet.h"
#include "graphics/niche/InkHUD/Applets/User/RecentsList/RecentsListApplet.h"
#include "graphics/niche/InkHUD/Applets/User/ThreadedMessage/ThreadedMessageApplet.h"
// Shared NicheGraphics components
// --------------------------------
#include "graphics/niche/Drivers/EInk/DEPG0290BNS800.h"
#include "graphics/niche/Inputs/TwoButton.h"
// Button feedback
#include "buzz.h"
void setupNicheGraphics()
{
using namespace NicheGraphics;
// SPI
// -----------------------------
// Display is connected to HSPI
SPIClass *hspi = new SPIClass(HSPI);
hspi->begin(PIN_EINK_SCLK, -1, PIN_EINK_MOSI, PIN_EINK_CS);
// E-Ink Driver
// -----------------------------
Drivers::EInk *driver = new Drivers::DEPG0290BNS800;
driver->begin(hspi, PIN_EINK_DC, PIN_EINK_CS, PIN_EINK_BUSY);
// InkHUD
// ----------------------------
InkHUD::InkHUD *inkhud = InkHUD::InkHUD::getInstance();
// Set the E-Ink driver
inkhud->setDriver(driver);
// Set how many FAST updates per FULL update
// Set how unhealthy additional FAST updates beyond this number are
inkhud->setDisplayResilience(7, 1.5);
// Select fonts
InkHUD::Applet::fontLarge = FREESANS_12PT_WIN1252;
InkHUD::Applet::fontMedium = FREESANS_9PT_WIN1252;
InkHUD::Applet::fontSmall = FREESANS_6PT_WIN1252;
// Customize default settings
inkhud->persistence->settings.userTiles.maxCount = 2; // How many tiles can the display handle?
inkhud->persistence->settings.rotation = 1; // 90 degrees clockwise
inkhud->persistence->settings.userTiles.count = 1; // One tile only by default, keep things simple for new users
inkhud->persistence->settings.optionalMenuItems.nextTile = false; // Behavior handled by aux button instead
// Pick applets
// Note: order of applets determines priority of "auto-show" feature
inkhud->addApplet("All Messages", new InkHUD::AllMessageApplet, true, true); // Activated, autoshown
inkhud->addApplet("DMs", new InkHUD::DMApplet); // -
inkhud->addApplet("Channel 0", new InkHUD::ThreadedMessageApplet(0)); // -
inkhud->addApplet("Channel 1", new InkHUD::ThreadedMessageApplet(1)); // -
inkhud->addApplet("Positions", new InkHUD::PositionsApplet, true); // Activated
inkhud->addApplet("Favorites Map", new InkHUD::FavoritesMapApplet); // -
inkhud->addApplet("Recents List", new InkHUD::RecentsListApplet); // -
inkhud->addApplet("Heard", new InkHUD::HeardApplet, true, false, 0); // Activated, not autoshown, default on tile 0
// Start running InkHUD
inkhud->begin();
// Buttons
// --------------------------
Inputs::TwoButton *buttons = Inputs::TwoButton::getInstance(); // A shared NicheGraphics component
// #0: Main User Button
buttons->setWiring(0, Inputs::TwoButton::getUserButtonPin());
buttons->setHandlerShortPress(0, [inkhud]() { inkhud->shortpress(); });
buttons->setHandlerLongPress(0, [inkhud]() { inkhud->longpress(); });
// #1: Aux Button
buttons->setWiring(1, PIN_BUTTON2);
buttons->setHandlerShortPress(1, [inkhud]() {
inkhud->nextTile();
playChirp();
});
// Begin handling button events
buttons->start();
}
#endif
code/firmware/variants/esp32s3/heltec_vision_master_e290/pins_arduino.h
+57
View File
@@ -0,0 +1,57 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 39;
static const uint8_t SCL = 38;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO1 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_vision_master_e290/platformio.ini
+53
View File
@@ -0,0 +1,53 @@
; Using the original screen class
[env:heltec-vision-master-e290]
custom_meshtastic_hw_model = 68
custom_meshtastic_hw_model_slug = HELTEC_VISION_MASTER_E290
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec Vision Master E290
custom_meshtastic_images = heltec-vision-master-e290.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board = heltec_vision_master_e290
board_build.partitions = default_8MB.csv
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/heltec_vision_master_e290
-D DISPLAY_FLIP_SCREEN ; Orient so the LoRa antenna faces up
-D HELTEC_VISION_MASTER_E290
-D BUTTON_CLICK_MS=200
-D EINK_DISPLAY_MODEL=GxEPD2_290_BN8
-D EINK_WIDTH=296
-D EINK_HEIGHT=128
-D USE_EINK
-D USE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
-D EINK_LIMIT_FASTREFRESH=10 ; How many consecutive fast-refreshes are permitted
-D EINK_HASQUIRK_GHOSTING ; Display model is identified as "prone to ghosting"
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
upload_speed = 115200
[env:heltec-vision-master-e290-inkhud]
extends = esp32s3_base, inkhud
board = heltec_vision_master_e290
board_build.partitions = default_8MB.csv
build_src_filter =
${esp32s3_base.build_src_filter}
${inkhud.build_src_filter}
build_flags =
${esp32s3_base.build_flags}
${inkhud.build_flags}
-I variants/esp32s3/heltec_vision_master_e290
-D HELTEC_VISION_MASTER_E290
lib_deps =
${inkhud.lib_deps} ; InkHUD libs first, so we get GFXRoot instead of AdafruitGFX
${esp32s3_base.lib_deps}
upload_speed = 921600
code/firmware/variants/esp32s3/heltec_vision_master_e290/variant.h
+53
View File
@@ -0,0 +1,53 @@
#define LED_POWER 45 // LED is not populated on earliest board variant
#define BUTTON_PIN 0
#define PIN_BUTTON2 21 // Second built-in button
#define ALT_BUTTON_PIN PIN_BUTTON2 // Send the up event
// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL
// Display (E-Ink)
#define PIN_EINK_CS 3
#define PIN_EINK_BUSY 6
#define PIN_EINK_DC 4
#define PIN_EINK_RES 5
#define PIN_EINK_SCLK 2
#define PIN_EINK_MOSI 1
// SPI
#define SPI_INTERFACES_COUNT 2
#define PIN_SPI_MISO 11
#define PIN_SPI_MOSI 10
#define PIN_SPI_SCK 9
// Power
#define VEXT_ENABLE 18 // Powers the E-Ink display only
#define VEXT_ON_VALUE HIGH
#define ADC_CTRL 46
#define ADC_CTRL_ENABLED HIGH
#define BATTERY_PIN 7
#define ADC_CHANNEL ADC1_GPIO7_CHANNEL
#define ADC_MULTIPLIER 4.9 * 1.03
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5
// LoRa
#define USE_SX1262
#define LORA_DIO0 RADIOLIB_NC // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
code/firmware/variants/esp32s3/heltec_vision_master_t190/pins_arduino.h
+57
View File
@@ -0,0 +1,57 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 2;
static const uint8_t SCL = 1;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO0 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_vision_master_t190/platformio.ini
+24
View File
@@ -0,0 +1,24 @@
[env:heltec-vision-master-t190]
custom_meshtastic_hw_model = 66
custom_meshtastic_hw_model_slug = HELTEC_VISION_MASTER_T190
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec Vision Master T190
custom_meshtastic_images = heltec-vision-master-t190.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board = heltec_vision_master_t190
board_build.partitions = default_8MB.csv
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/heltec_vision_master_t190
-D HELTEC_VISION_MASTER_T190
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-st7789 packageName=https://github.com/meshtastic/st7789 gitBranch=main
https://github.com/meshtastic/st7789/archive/9ee76d6b18b9a8f45a2c5cae06b1134a587691eb.zip
upload_speed = 921600
code/firmware/variants/esp32s3/heltec_vision_master_t190/variant.h
+73
View File
@@ -0,0 +1,73 @@
#ifndef HAS_TFT
#define BUTTON_PIN 0
#define PIN_BUTTON2 21 // Second built-in button
#define ALT_BUTTON_PIN PIN_BUTTON2 // Send the up event
// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL
// Display (TFT)
#define USE_ST7789
#define ST7789_NSS 39
#define ST7789_RS 47 // DC
#define ST7789_SDA 48 // MOSI
#define ST7789_SCK 38
#define ST7789_RESET 40
#define ST7789_MISO 4
#define ST7789_BUSY -1
#define VTFT_CTRL 7
#define VTFT_LEDA 17
#define TFT_BACKLIGHT_ON HIGH
#define ST7789_SPI_HOST SPI2_HOST
#define SPI_FREQUENCY 10000000
#define SPI_READ_FREQUENCY 10000000
#define TFT_HEIGHT 170
#define TFT_WIDTH 320
#define TFT_OFFSET_X 0
#define TFT_OFFSET_Y 0
// #define TFT_OFFSET_ROTATION 0
// #define SCREEN_ROTATE
// #define SCREEN_TRANSITION_FRAMERATE 5
#define BRIGHTNESS_DEFAULT 100 // Medium Low Brightnes
// #define SLEEP_TIME 120
// SPI
#define SPI_INTERFACES_COUNT 2
#define PIN_SPI_MISO 11
#define PIN_SPI_MOSI 10
#define PIN_SPI_SCK 9
// Power
#define VEXT_ENABLE 5
#define VEXT_ON_VALUE HIGH
#define ADC_CTRL 46
#define ADC_CTRL_ENABLED HIGH
#define BATTERY_PIN 6
#define ADC_CHANNEL ADC1_GPIO6_CHANNEL
#define ADC_MULTIPLIER 4.9 * 1.03 // Voltage divider is roughly 1:1
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // Voltage divider output is quite high
// LoRa
#define USE_SX1262
#define LORA_DIO0 RADIOLIB_NC // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#endif // HAS_TFT
code/firmware/variants/esp32s3/heltec_wireless_paper/einkDetect.h
+35
View File
@@ -0,0 +1,35 @@
#pragma once
#include "configuration.h"
enum class EInkDetectionResult : uint8_t {
LCMEN213EFC1 = 0, // V1.1
E0213A367 = 1, // V1.1.1, V1.2
};
EInkDetectionResult detectEInk()
{
// Test 1: Logic of BUSY pin
// Determines controller IC manufacturer
// Fitipower: busy when LOW
// Solomon Systech: busy when HIGH
// Force display BUSY by holding reset pin active
pinMode(PIN_EINK_RES, OUTPUT);
digitalWrite(PIN_EINK_RES, LOW);
delay(10);
// Read whether pin is HIGH or LOW while busy
pinMode(PIN_EINK_BUSY, INPUT);
bool busyLogic = digitalRead(PIN_EINK_BUSY);
// Test complete. Release pin
pinMode(PIN_EINK_RES, INPUT);
if (busyLogic == LOW)
return EInkDetectionResult::LCMEN213EFC1;
else // busy HIGH
return EInkDetectionResult::E0213A367;
}
code/firmware/variants/esp32s3/heltec_wireless_paper/nicheGraphics.h
+112
View File
@@ -0,0 +1,112 @@
#pragma once
#include "configuration.h"
#ifdef MESHTASTIC_INCLUDE_NICHE_GRAPHICS
// InkHUD-specific components
// ---------------------------
#include "graphics/niche/InkHUD/InkHUD.h"
// Applets
#include "graphics/niche/InkHUD/Applets/User/AllMessage/AllMessageApplet.h"
#include "graphics/niche/InkHUD/Applets/User/DM/DMApplet.h"
#include "graphics/niche/InkHUD/Applets/User/FavoritesMap/FavoritesMapApplet.h"
#include "graphics/niche/InkHUD/Applets/User/Heard/HeardApplet.h"
#include "graphics/niche/InkHUD/Applets/User/Positions/PositionsApplet.h"
#include "graphics/niche/InkHUD/Applets/User/RecentsList/RecentsListApplet.h"
#include "graphics/niche/InkHUD/Applets/User/ThreadedMessage/ThreadedMessageApplet.h"
// Shared NicheGraphics components
// --------------------------------
#include "graphics/niche/Drivers/EInk/E0213A367.h"
#include "graphics/niche/Drivers/EInk/LCMEN2R13EFC1.h"
#include "graphics/niche/Inputs/TwoButton.h"
#include "einkDetect.h" // Detect display model at runtime
void setupNicheGraphics()
{
using namespace NicheGraphics;
// Detect E-Ink Model
// -------------------
EInkDetectionResult displayModel = detectEInk();
// SPI
// -----------------------------
// Display is connected to HSPI
SPIClass *hspi = new SPIClass(HSPI);
hspi->begin(PIN_EINK_SCLK, -1, PIN_EINK_MOSI, PIN_EINK_CS);
// E-Ink Driver
// -----------------------------
Drivers::EInk *driver;
if (displayModel == EInkDetectionResult::LCMEN213EFC1) // V1.1
driver = new Drivers::LCMEN213EFC1;
else if (displayModel == EInkDetectionResult::E0213A367) // V1.1.1, V1.2
driver = new Drivers::E0213A367;
driver->begin(hspi, PIN_EINK_DC, PIN_EINK_CS, PIN_EINK_BUSY, PIN_EINK_RES);
// InkHUD
// ----------------------------
InkHUD::InkHUD *inkhud = InkHUD::InkHUD::getInstance();
// Set the E-Ink driver
inkhud->setDriver(driver);
// Set how many FAST updates per FULL update
// Set how unhealthy additional FAST updates beyond this number are
if (displayModel == EInkDetectionResult::LCMEN213EFC1) // V1.1 (unmarked)
inkhud->setDisplayResilience(10, 1.5);
else if (displayModel == EInkDetectionResult::E0213A367) // V1.1.1, V1.2
inkhud->setDisplayResilience(15, 3);
// Select fonts
InkHUD::Applet::fontLarge = FREESANS_12PT_WIN1252;
InkHUD::Applet::fontMedium = FREESANS_9PT_WIN1252;
InkHUD::Applet::fontSmall = FREESANS_6PT_WIN1252;
// Customize default settings
inkhud->persistence->settings.userTiles.maxCount = 2; // How many tiles can the display handle?
inkhud->persistence->settings.rotation = 3; // 270 degrees clockwise
inkhud->persistence->settings.userTiles.count = 1; // One tile only by default, keep things simple for new users
// Pick applets
// Note: order of applets determines priority of "auto-show" feature
inkhud->addApplet("All Messages", new InkHUD::AllMessageApplet, true, true); // Activated, autoshown
inkhud->addApplet("DMs", new InkHUD::DMApplet); // -
inkhud->addApplet("Channel 0", new InkHUD::ThreadedMessageApplet(0)); // -
inkhud->addApplet("Channel 1", new InkHUD::ThreadedMessageApplet(1)); // -
inkhud->addApplet("Positions", new InkHUD::PositionsApplet, true); // Activated
inkhud->addApplet("Recents List", new InkHUD::RecentsListApplet); // -
inkhud->addApplet("Heard", new InkHUD::HeardApplet, true, false, 0); // Activated, not autoshown, default on tile 0
inkhud->addApplet("Favorites Map", new InkHUD::FavoritesMapApplet, false, false); // -
// Start running InkHUD
inkhud->begin();
// Buttons
// --------------------------
Inputs::TwoButton *buttons = Inputs::TwoButton::getInstance(); // Shared NicheGraphics component
// #0: Main User Button
buttons->setWiring(0, Inputs::TwoButton::getUserButtonPin());
buttons->setHandlerShortPress(0, [inkhud]() { inkhud->shortpress(); });
buttons->setHandlerLongPress(0, [inkhud]() { inkhud->longpress(); });
// No aux button on this board
// Begin handling button events
buttons->start();
}
#endif
code/firmware/variants/esp32s3/heltec_wireless_paper/pins_arduino.h
+57
View File
@@ -0,0 +1,57 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 41;
static const uint8_t SCL = 42;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO1 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_wireless_paper/platformio.ini
+50
View File
@@ -0,0 +1,50 @@
; Using the original screen class
[env:heltec-wireless-paper]
custom_meshtastic_hw_model = 49
custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_PAPER
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec Wireless Paper
custom_meshtastic_images = heltec-wireless-paper.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board = heltec_wifi_lora_32_V3
board_build.partitions = default_8MB.csv
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/heltec_wireless_paper
-D HELTEC_WIRELESS_PAPER
-D GXEPD2_DRIVER_0=GxEPD2_213_FC1
-D GXEPD2_DRIVER_1=GxEPD2_213_E0213A367
-D EINK_WIDTH=250
-D EINK_HEIGHT=122
-D USE_EINK
-D USE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
-D EINK_LIMIT_FASTREFRESH=10 ; How many consecutive fast-refreshes are permitted
-D EINK_BACKGROUND_USES_FAST ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
-D EINK_HASQUIRK_GHOSTING ; Display model is identified as "prone to ghosting"
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
upload_speed = 115200
[env:heltec-wireless-paper-inkhud]
extends = esp32s3_base, inkhud
board = heltec_wifi_lora_32_V3
board_build.partitions = default_8MB.csv
build_src_filter =
${esp32s3_base.build_src_filter}
${inkhud.build_src_filter}
build_flags =
${esp32s3_base.build_flags}
${inkhud.build_flags}
-I variants/esp32s3/heltec_wireless_paper
-D HELTEC_WIRELESS_PAPER
lib_deps =
${inkhud.lib_deps} ; InkHUD libs first, so we get GFXRoot instead of AdafruitGFX
${esp32s3_base.lib_deps}
upload_speed = 921600
code/firmware/variants/esp32s3/heltec_wireless_paper/variant.h
+55
View File
@@ -0,0 +1,55 @@
#define LED_POWER 18
#define BUTTON_PIN 0
// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL
// Display (E-Ink)
#define PIN_EINK_CS 4
#define PIN_EINK_BUSY 7
#define PIN_EINK_DC 5
#define PIN_EINK_RES 6
#define PIN_EINK_SCLK 3
#define PIN_EINK_MOSI 2
// SPI
#define SPI_INTERFACES_COUNT 2
#define PIN_SPI_MISO 11
#define PIN_SPI_MOSI 10
#define PIN_SPI_SCK 9
// Power
#define VEXT_ENABLE 45 // Active low, powers the E-Ink display
#define VEXT_ON_VALUE LOW
#define ADC_CTRL 19
#define BATTERY_PIN 20
#define ADC_CHANNEL ADC2_GPIO20_CHANNEL
#define ADC_MULTIPLIER 2 // Voltage divider is roughly 1:1
#define BAT_MEASURE_ADC_UNIT 2 // Use ADC2
#define ADC_ATTENUATION ADC_ATTEN_DB_12 // Voltage divider output is quite high
#define ADC_CTRL_ENABLED LOW
#define NO_EXT_GPIO 1
#define NO_GPS 1
// LoRa
#define USE_SX1262
#define LORA_DIO0 RADIOLIB_NC // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
code/firmware/variants/esp32s3/heltec_wireless_paper_v1/pins_arduino.h
+62
View File
@@ -0,0 +1,62 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
static const uint8_t KEY_BUILTIN = 0;
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 41;
static const uint8_t SCL = 42;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t Vext = 45;
static const uint8_t LED = 18;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO1 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_wireless_paper_v1/platformio.ini
+30
View File
@@ -0,0 +1,30 @@
[env:heltec-wireless-paper-v1_0]
custom_meshtastic_hw_model = 57
custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_PAPER_V1_0
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = false
custom_meshtastic_support_level = 3
custom_meshtastic_display_name = Heltec Wireless Paper V1.0
custom_meshtastic_images = heltec-wireless-paper-v1_0.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board_level = extra
board = heltec_wifi_lora_32_V3
board_build.partitions = default_8MB.csv
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/heltec_wireless_paper_v1
-D HELTEC_WIRELESS_PAPER_V1_0
-D EINK_DISPLAY_MODEL=GxEPD2_213_BN
-D EINK_WIDTH=250
-D EINK_HEIGHT=122
-D USE_EINK_DYNAMICDISPLAY ; Enable Dynamic EInk
-D EINK_LIMIT_FASTREFRESH=5 ; How many consecutive fast-refreshes are permitted
-D EINK_LIMIT_GHOSTING_PX=2000 ; (Optional) How much image ghosting is tolerated
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
upload_speed = 115200
code/firmware/variants/esp32s3/heltec_wireless_paper_v1/variant.h
+56
View File
@@ -0,0 +1,56 @@
#define LED_POWER 18
#define BUTTON_PIN 0
// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL
// Display (E-Ink)
#define USE_EINK
#define PIN_EINK_CS 4
#define PIN_EINK_BUSY 7
#define PIN_EINK_DC 5
#define PIN_EINK_RES 6
#define PIN_EINK_SCLK 3
#define PIN_EINK_MOSI 2
// SPI
#define SPI_INTERFACES_COUNT 2
#define PIN_SPI_MISO 11
#define PIN_SPI_MOSI 10
#define PIN_SPI_SCK 9
// Power
#define VEXT_ENABLE 45 // Active low, powers the E-Ink display
#define VEXT_ON_VALUE LOW
#define ADC_CTRL 19
#define BATTERY_PIN 20
#define ADC_CHANNEL ADC2_GPIO20_CHANNEL
#define ADC_MULTIPLIER 2 // Voltage divider is roughly 1:1
#define BAT_MEASURE_ADC_UNIT 2 // Use ADC2
#define ADC_ATTENUATION ADC_ATTEN_DB_12 // Voltage divider output is quite high
#define ADC_CTRL_ENABLED LOW
#define NO_EXT_GPIO 1
#define NO_GPS 1
// LoRa
#define USE_SX1262
#define LORA_DIO0 RADIOLIB_NC // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
code/firmware/variants/esp32s3/heltec_wireless_tracker/pins_arduino.h
+68
View File
@@ -0,0 +1,68 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include "soc/soc_caps.h"
#include <stdint.h>
#define WIFI_LoRa_32_V3 true
#define DISPLAY_HEIGHT 80
#define DISPLAY_WIDTH 160
#define USB_VID 0x303a
#define USB_PID 0x1001
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 45;
static const uint8_t SCL = 46;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t Vext = 36;
static const uint8_t LED = 18;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO0 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_wireless_tracker/platformio.ini
+27
View File
@@ -0,0 +1,27 @@
[env:heltec-wireless-tracker]
custom_meshtastic_hw_model = 48
custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_TRACKER
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec Wireless Tracker V1.1
custom_meshtastic_images = heltec-wireless-tracker.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board = heltec_wireless_tracker
board_build.partitions = default_8MB.csv
upload_protocol = esptool
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/heltec_wireless_tracker
-D HELTEC_TRACKER_V1_1
;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
lovyan03/LovyanGFX@1.2.19
code/firmware/variants/esp32s3/heltec_wireless_tracker/variant.h
+79
View File
@@ -0,0 +1,79 @@
#define LED_POWER 18
#define _VARIANT_HELTEC_WIRELESS_TRACKER
#define HELTEC_TRACKER_V1_X
// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL
// ST7735S TFT LCD
#define ST7735S 1 // there are different (sub-)versions of ST7735
#define ST7735_CS 38
#define ST7735_RS 40 // DC
#define ST7735_SDA 42 // MOSI
#define ST7735_SCK 41
#define ST7735_RESET 39
#define ST7735_MISO -1
#define ST7735_BUSY -1
#define TFT_BL 21 /* V1.1 PCB marking */
#define ST7735_SPI_HOST SPI3_HOST
#define SPI_FREQUENCY 40000000
#define SPI_READ_FREQUENCY 16000000
#define SCREEN_ROTATE
#define TFT_HEIGHT DISPLAY_WIDTH
#define TFT_WIDTH DISPLAY_HEIGHT
#define TFT_OFFSET_X 26
#define TFT_OFFSET_Y -1
#define SCREEN_TRANSITION_FRAMERATE 3 // fps
#define DISPLAY_FORCE_SMALL_FONTS
#define USE_TFTDISPLAY 1
// pin 3 is Vext on v1.1 - HIGH enables LDO for Vext rail which goes to:
// GPS UC6580: GPS V_DET(8), VDD_IO(7), DCDC_IN(21), pulls up RESETN(17), D_SEL(33) and BOOT_MODE(34) through 10kR
// GPS LNA SW7125DE: VCC(4), pulls up SHDN(5) through 10kR
// LED: VDD, LEDA (through diode)
#define VEXT_ENABLE 3 // active HIGH - powers the GPS, GPS LNA and OLED
#define VEXT_ON_VALUE HIGH
#define BUTTON_PIN 0
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER 4.9 * 1.045
#define ADC_CTRL 2 // active HIGH, powers the voltage divider. Only on 1.1
#define ADC_USE_PULLUP // Use internal pullup/pulldown instead of actively driving the output
#undef GPS_RX_PIN
#undef GPS_TX_PIN
#define GPS_RX_PIN 33
#define GPS_TX_PIN 34
#define PIN_GPS_RESET 35
#define PIN_GPS_PPS 36
// #define PIN_GPS_EN 3 // Uncomment to power off the GPS with triple-click on Tracker v1.1, though we'll also lose the
// display.
#define GPS_RESET_MODE LOW
#define GPS_UC6580
#define GPS_BAUDRATE 115200
#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
code/firmware/variants/esp32s3/heltec_wireless_tracker_V1_0/pins_arduino.h
+68
View File
@@ -0,0 +1,68 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include "soc/soc_caps.h"
#include <stdint.h>
#define WIFI_LoRa_32_V3 true
#define DISPLAY_HEIGHT 80
#define DISPLAY_WIDTH 160
#define USB_VID 0x303a
#define USB_PID 0x1001
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 5;
static const uint8_t SCL = 6;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t Vext = 36;
static const uint8_t LED = 18;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO0 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_wireless_tracker_V1_0/platformio.ini
+25
View File
@@ -0,0 +1,25 @@
[env:heltec-wireless-tracker-V1-0]
custom_meshtastic_hw_model = 58
custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_TRACKER_V1_0
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = false
custom_meshtastic_support_level = 3
custom_meshtastic_display_name = Heltec Wireless Tracker V1.0
custom_meshtastic_images = heltec-wireless-tracker.svg
custom_meshtastic_requires_dfu = true
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board_level = extra
board = heltec_wireless_tracker
board_build.partitions = default_8MB.csv
upload_protocol = esptool
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/heltec_wireless_tracker_V1_0
-D HELTEC_TRACKER_V1_0
;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
lovyan03/LovyanGFX@1.2.19
code/firmware/variants/esp32s3/heltec_wireless_tracker_V1_0/variant.h
+74
View File
@@ -0,0 +1,74 @@
#define LED_POWER 18
#define HELTEC_TRACKER_V1_X
// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL
// ST7735S TFT LCD
#define ST7735S 1 // there are different (sub-)versions of ST7735
#define ST7735_CS 38
#define ST7735_RS 40 // DC
#define ST7735_SDA 42 // MOSI
#define ST7735_SCK 41
#define ST7735_RESET 39
#define ST7735_MISO -1
#define ST7735_BUSY -1
#define TFT_BL 45
#define ST7735_SPI_HOST SPI3_HOST
#define SPI_FREQUENCY 40000000
#define SPI_READ_FREQUENCY 16000000
#define SCREEN_ROTATE
#define TFT_HEIGHT DISPLAY_WIDTH
#define TFT_WIDTH DISPLAY_HEIGHT
#define TFT_OFFSET_X 26
#define TFT_OFFSET_Y -1
#define VTFT_CTRL 46 // Heltec Tracker needs this pulled low for TFT
#define SCREEN_TRANSITION_FRAMERATE 3 // fps
#define DISPLAY_FORCE_SMALL_FONTS
#define FORCE_LOW_RES 1
#define USE_TFTDISPLAY 1
#define VEXT_ENABLE Vext // active low, powers the oled display and the lora antenna boost
#define VEXT_ON_VALUE LOW
#define BUTTON_PIN 0
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER 4.9 * 1.045
#undef GPS_RX_PIN
#undef GPS_TX_PIN
#define GPS_RX_PIN 33
#define GPS_TX_PIN 34
#define PIN_GPS_RESET 35
#define PIN_GPS_PPS 36
#define PIN_GPS_EN 37 // Heltec Tracker needs this pulled low for GPS
#define GPS_EN_ACTIVE LOW
#define GPS_RESET_MODE LOW
#define GPS_UC6580
#define GPS_BAUDRATE 115200
#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
code/firmware/variants/esp32s3/heltec_wireless_tracker_v2/pins_arduino.h
+67
View File
@@ -0,0 +1,67 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include "soc/soc_caps.h"
#include <stdint.h>
#define DISPLAY_HEIGHT 80
#define DISPLAY_WIDTH 160
#define USB_VID 0x303a
#define USB_PID 0x1001
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 5;
static const uint8_t SCL = 6;
static const uint8_t SS = 8;
static const uint8_t MOSI = 10;
static const uint8_t MISO = 11;
static const uint8_t SCK = 9;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t A13 = 14;
static const uint8_t A14 = 15;
static const uint8_t A15 = 16;
static const uint8_t A16 = 17;
static const uint8_t A17 = 18;
static const uint8_t A18 = 19;
static const uint8_t A19 = 20;
static const uint8_t T1 = 1;
static const uint8_t T2 = 2;
static const uint8_t T3 = 3;
static const uint8_t T4 = 4;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T13 = 13;
static const uint8_t T14 = 14;
static const uint8_t Vext = 3;
static const uint8_t LED = 18;
static const uint8_t RST_LoRa = 12;
static const uint8_t BUSY_LoRa = 13;
static const uint8_t DIO0 = 14;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/heltec_wireless_tracker_v2/platformio.ini
+23
View File
@@ -0,0 +1,23 @@
[env:heltec-wireless-tracker-v2]
custom_meshtastic_support_level = 1
custom_meshtastic_images = heltec_wireless_tracker_v2.svg
custom_meshtastic_tags = Heltec
extends = esp32s3_base
board = heltec_wireless_tracker_v2
board_build.partitions = default_8MB.csv
upload_protocol = esptool
custom_meshtastic_hw_model = 113
custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_TRACKER_V2
custom_meshtastic_architecture = esp32s3
custom_meshtastic_display_name = Heltec Wireless Tracker V2
custom_meshtastic_actively_supported = true
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/heltec_wireless_tracker_v2
-D HELTEC_WIRELESS_TRACKER_V2
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
lovyan03/LovyanGFX@1.2.19
code/firmware/variants/esp32s3/heltec_wireless_tracker_v2/variant.h
+101
View File
@@ -0,0 +1,101 @@
#define LED_POWER 18
#define _VARIANT_HELTEC_WIRELESS_TRACKER
// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL
// ST7735S TFT LCD
#define ST7735S 1 // there are different (sub-)versions of ST7735
#define ST7735_CS 38
#define ST7735_RS 40 // DC
#define ST7735_SDA 42 // MOSI
#define ST7735_SCK 41
#define ST7735_RESET 39
#define ST7735_MISO -1
#define ST7735_BUSY -1
#define TFT_BL 21
#define ST7735_SPI_HOST SPI3_HOST
#define SPI_FREQUENCY 40000000
#define SPI_READ_FREQUENCY 16000000
#define SCREEN_ROTATE
#define TFT_HEIGHT DISPLAY_WIDTH
#define TFT_WIDTH DISPLAY_HEIGHT
#define TFT_OFFSET_X 24
#define TFT_OFFSET_Y 0
#define TFT_INVERT false
#define SCREEN_TRANSITION_FRAMERATE 3 // fps
#define DISPLAY_FORCE_SMALL_FONTS
#define USE_TFTDISPLAY 1
#define VEXT_ENABLE 3 // active HIGH - powers the GPS, GPS LNA and OLED
#define VEXT_ON_VALUE HIGH
#define BUTTON_PIN 0
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER 4.9 * 1.045
#define ADC_CTRL 2 // active HIGH, powers the voltage divider.
#define ADC_USE_PULLUP // Use internal pullup/pulldown instead of actively driving the output
#undef GPS_RX_PIN
#undef GPS_TX_PIN
#define GPS_RX_PIN 33
#define GPS_TX_PIN 34
#define PIN_GPS_RESET 35
#define PIN_GPS_PPS 36
// #define PIN_GPS_EN 3 // Uncomment to power off the GPS with triple-click on Tracker v2, though we'll also lose the
// display.
#define GPS_RESET_MODE LOW
#define GPS_UC6580
#define GPS_BAUDRATE 115200
#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TCXO is enabled
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
// ---- GC1109 RF FRONT END CONFIGURATION ----
// The Heltec Wireless Tracker V2 uses a GC1109 FEM chip with integrated PA and LNA
// RF path: SX1262 -> GC1109 PA -> Pi attenuator -> Antenna
// Measured net TX gain (non-linear due to PA compression):
// +11dB at 0-15dBm input (e.g., 10dBm in -> 21dBm out)
// +10dB at 16-17dBm input
// +9dB at 18-19dBm input
// +7dB at 21dBm input (e.g., 21dBm in -> 28dBm out max)
// Control logic (from GC1109 datasheet):
// Shutdown: CSD=0, CTX=X, CPS=X
// Receive LNA: CSD=1, CTX=0, CPS=X (17dB gain, 2dB NF)
// Transmit bypass: CSD=1, CTX=1, CPS=0 (~1dB loss, no PA)
// Transmit PA: CSD=1, CTX=1, CPS=1 (full PA enabled)
// Pin mapping:
// CTX (pin 6) -> SX1262 DIO2: TX/RX path select (automatic via SX126X_DIO2_AS_RF_SWITCH)
// CSD (pin 4) -> GPIO4: Chip enable (HIGH=on, LOW=shutdown)
// CPS (pin 5) -> GPIO46: PA mode select (HIGH=full PA, LOW=bypass)
// VCC0/VCC1 -> Vfem via U3 LDO, controlled by GPIO7
#define USE_GC1109_PA
#define LORA_PA_POWER 7 // VFEM_Ctrl - GC1109 LDO power enable
#define LORA_PA_EN 4 // CSD - GC1109 chip enable (HIGH=on)
#define LORA_PA_TX_EN 46 // CPS - GC1109 PA mode (HIGH=full PA, LOW=bypass)
// GC1109 FEM: TX/RX path switching is handled by DIO2 -> CTX pin (via SX126X_DIO2_AS_RF_SWITCH)
// GPIO46 is CPS (PA mode), not TX control - setTransmitEnable() handles it in SX126xInterface.cpp
// Do NOT use SX126X_TXEN/RXEN as that would cause double-control of GPIO46
code/firmware/variants/esp32s3/heltec_wsl_v3/platformio.ini
+20
View File
@@ -0,0 +1,20 @@
[env:heltec-wsl-v3]
custom_meshtastic_hw_model = 44
custom_meshtastic_hw_model_slug = HELTEC_WSL_V3
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = Heltec Wireless Stick Lite V3
custom_meshtastic_images = heltec-wsl-v3.svg
custom_meshtastic_tags = Heltec
custom_meshtastic_partition_scheme = 8MB
extends = esp32s3_base
board = heltec_wifi_lora_32_V3
board_build.partitions = default_8MB.csv
# Temporary until espressif creates a release with this new target
build_flags =
${esp32s3_base.build_flags}
-D HELTEC_WSL_V3
-I variants/esp32s3/heltec_wsl_v3
-ULED_BUILTIN
code/firmware/variants/esp32s3/heltec_wsl_v3/variant.h
+36
View File
@@ -0,0 +1,36 @@
#define I2C_SCL SCL
#define I2C_SDA SDA
#define LED_POWER LED
#define VEXT_ENABLE Vext // active low, powers the oled display and the lora antenna boost
#define VEXT_ON_VALUE LOW
#define BUTTON_PIN 0
#define ADC_CTRL 37
#define ADC_CTRL_ENABLED LOW
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER 4.9 * 1.045
#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
code/firmware/variants/esp32s3/icarus/pins_arduino.h
+21
View File
@@ -0,0 +1,21 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x2886
#define USB_PID 0x0059
// GPIO48 Reference: https://github.com/espressif/arduino-esp32/pull/8600
// The default Wire will be mapped to Screen and Sensors
static const uint8_t SDA = 8;
static const uint8_t SCL = 9;
// Default SPI will be mapped to Radio
static const uint8_t MISO = 39;
static const uint8_t SCK = 21;
static const uint8_t MOSI = 38;
static const uint8_t SS = 17;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/icarus/platformio.ini
+18
View File
@@ -0,0 +1,18 @@
[env:icarus]
extends = esp32s3_base
board = icarus
board_level = extra
board_check = true
board_build.mcu = esp32s3
board_build.partitions = default_8MB.csv
upload_protocol = esptool
upload_speed = 921600
build_unflags =
${esp32s3_base.build_unflags}
-DARDUINO_USB_MODE=1
build_flags =
${esp32s3_base.build_flags}
-D PRIVATE_HW
-I variants/esp32s3/icarus
-DBOARD_HAS_PSRAM
-DARDUINO_USB_MODE=0
code/firmware/variants/esp32s3/icarus/variant.h
+31
View File
@@ -0,0 +1,31 @@
// Icarus has a 1.3 inch OLED Screen
#define SCREEN_SSD106
#define I2C_SDA 8
#define I2C_SCL 9
#define I2C_SDA1 18
#define I2C_SCL1 6
#define BUTTON_PIN 7 // Selection button
// RA-01SH/HT-RA62 LORA module
#define USE_SX1262
#define LORA_MISO 39
#define LORA_SCK 21
#define LORA_MOSI 38
#define LORA_CS 17
#define LORA_RESET 42
#define LORA_DIO1 5
#ifdef USE_SX1262
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY 47
#define SX126X_RESET LORA_RESET
// DIO2 controlls an antenna switch
#define SX126X_DIO2_AS_RF_SWITCH
#endif
code/firmware/variants/esp32s3/link32_s3_v1/pins_arduino.h
+19
View File
@@ -0,0 +1,19 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// The default Wire will be mapped to PMU and RTC
static const uint8_t SDA = 47;
static const uint8_t SCL = 48;
// Default SPI will be mapped to Radio
static const uint8_t SS = 21;
static const uint8_t MOSI = 34;
static const uint8_t MISO = 33;
static const uint8_t SCK = 16;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/link32_s3_v1/platformio.ini
+13
View File
@@ -0,0 +1,13 @@
[env:link32-s3-v1]
extends = esp32s3_base
board = esp32-s3-devkitc-1
board_level = extra
build_flags =
${esp32s3_base.build_flags}
-D LINK_32
-I variants/esp32s3/link32_s3_v1
-DARDUINO_USB_CDC_ON_BOOT
-DARDUINO_USB_MODE=1
-DRADIOLIB_EXCLUDE_SX128X=1
-DRADIOLIB_EXCLUDE_SX127X=1
-DRADIOLIB_EXCLUDE_LR11X0=1
code/firmware/variants/esp32s3/link32_s3_v1/variant.h
+44
View File
@@ -0,0 +1,44 @@
#define BATTERY_PIN 15
#define ADC_CHANNEL ADC2_GPIO15_CHANNEL // ADC channel for battery voltage measurement
#define BATTERY_SENSE_SAMPLES 30
#define BAT_MEASURE_ADC_UNIT 2 // Use ADC2 for battery measurement
#define USE_SSD1306
#define BUTTON_PIN 0 // Button pin for this board
#define CANCEL_BUTTON_PIN 36
#define CANCEL_BUTTON_ACTIVE_LOW true
#define CANCEL_BUTTON_ACTIVE_PULLUP true
#define HAS_NEOPIXEL // If defined, we will use the neopixel library
#define NEOPIXEL_DATA 35 // Neopixel pin for this board
#define NEOPIXEL_COUNT 1 // Number of neopixels on this board
#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
#define ADC_MULTIPLIER 2
#define I2C_SDA 47 // I2C pins for this board
#define I2C_SCL 48
#define USE_SX1262
#define LORA_SCK 16
#define LORA_MISO 33
#define LORA_MOSI 34
#define LORA_CS 21
#define LORA_RESET 18
#define LORA_DIO0 12 // a No connect on the SX1262 module
#define LORA_DIO1 13
#define LORA_DIO2 14 // Not really used
#define LORA_TCXO_GPIO 17
#define TCXO_OPTIONAL
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
code/firmware/variants/esp32s3/m5stack_cores3/pins_arduino.h
+60
View File
@@ -0,0 +1,60 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include "soc/soc_caps.h"
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// Some boards have too low voltage on this pin (board design bug)
// Use different pin with 3V and connect with 48
// and change this setup for the chosen pin (for example 38)
#define RGB_BUILTIN SOC_GPIO_PIN_COUNT + 48
#define RGB_BRIGHTNESS 64
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t TXD2 = 17;
static const uint8_t RXD2 = 18;
static const uint8_t SDA = 12;
static const uint8_t SCL = 11;
static const uint8_t SS = 15;
static const uint8_t MOSI = 37;
static const uint8_t MISO = 35;
static const uint8_t SCK = 36;
static const uint8_t G0 = 0;
static const uint8_t G1 = 1;
static const uint8_t G2 = 2;
static const uint8_t G3 = 3;
static const uint8_t G4 = 4;
static const uint8_t G5 = 5;
static const uint8_t G6 = 6;
static const uint8_t G7 = 7;
static const uint8_t G8 = 8;
static const uint8_t G9 = 9;
static const uint8_t G11 = 11;
static const uint8_t G12 = 12;
static const uint8_t G13 = 13;
static const uint8_t G14 = 14;
static const uint8_t G17 = 17;
static const uint8_t G18 = 18;
static const uint8_t G19 = 19;
static const uint8_t G20 = 20;
static const uint8_t G21 = 21;
static const uint8_t G33 = 33;
static const uint8_t G34 = 34;
static const uint8_t G35 = 35;
static const uint8_t G36 = 36;
static const uint8_t G37 = 37;
static const uint8_t G38 = 38;
static const uint8_t G45 = 45;
static const uint8_t G46 = 46;
static const uint8_t ADC = 10;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/m5stack_cores3/platformio.ini
+12
View File
@@ -0,0 +1,12 @@
; M5stack CoreS3
[env:m5stack-cores3]
extends = esp32s3_base
board = m5stack-cores3
board_check = true
board_build.partitions = default_16MB.csv
upload_protocol = esptool
build_flags =
${esp32s3_base.build_flags}
-D PRIVATE_HW
-D M5STACK_CORES3
-I variants/esp32s3/m5stack_cores3
code/firmware/variants/esp32s3/m5stack_cores3/variant.h
+22
View File
@@ -0,0 +1,22 @@
#define I2C_SDA 12
#define I2C_SCL 11
#undef LORA_SCK
#undef LORA_MISO
#undef LORA_MOSI
#undef LORA_CS
#define LORA_SCK 36
#define LORA_MISO 35
#define LORA_MOSI 37
#define LORA_CS 6 // NSS
#define USE_RF95
#define LORA_DIO0 14 // IRQ
#define LORA_RESET 5 // RESET
#define LORA_RST 5 // RESET
#define LORA_IRQ 14 // DIO0
#define LORA_DIO1 RADIOLIB_NC // Not really used
#define LORA_DIO2 RADIOLIB_NC // Not really used
#define HAS_AXP2101
code/firmware/variants/esp32s3/mesh-tab/pins_arduino.h
+61
View File
@@ -0,0 +1,61 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include "soc/soc_caps.h"
#include <stdint.h>
#define USB_VID 0x303A
#define USB_PID 0x80D6
static const uint8_t TX = 43;
static const uint8_t RX = 44;
static const uint8_t SDA = 8;
static const uint8_t SCL = 9;
static const uint8_t SS = 5;
static const uint8_t MOSI = 35;
static const uint8_t MISO = 37;
static const uint8_t SDO = 35;
static const uint8_t SDI = 37;
static const uint8_t SCK = 36;
static const uint8_t A0 = 1;
static const uint8_t A1 = 2;
static const uint8_t A2 = 3;
static const uint8_t A3 = 4;
static const uint8_t A4 = 5;
static const uint8_t A5 = 6;
static const uint8_t A6 = 7;
static const uint8_t A7 = 8;
static const uint8_t A8 = 9;
static const uint8_t A9 = 10;
static const uint8_t A10 = 11;
static const uint8_t A11 = 12;
static const uint8_t A12 = 13;
static const uint8_t T1 = 1;
static const uint8_t T3 = 3;
static const uint8_t T5 = 5;
static const uint8_t T6 = 6;
static const uint8_t T7 = 7;
static const uint8_t T8 = 8;
static const uint8_t T9 = 9;
static const uint8_t T10 = 10;
static const uint8_t T11 = 11;
static const uint8_t T12 = 12;
static const uint8_t T14 = 14;
static const uint8_t VBAT_SENSE = 2;
static const uint8_t VBUS_SENSE = 34;
static const uint8_t RGB_DATA = 40;
// RGB_BUILTIN and RGB_BRIGHTNESS can be used in new Arduino API neopixelWrite()
#define RGB_BUILTIN (RGB_DATA + SOC_GPIO_PIN_COUNT)
#define RGB_BRIGHTNESS 64
static const uint8_t RGB_PWR = 39;
static const uint8_t LDO2 = 39;
static const uint8_t LED = 13;
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/mesh-tab/platformio.ini
+182
View File
@@ -0,0 +1,182 @@
; Base for Mesh-Tab device (esp32-s3 N16R2 + ra-sh01 lora)
; https://github.com/valzzu/Mesh-Tab
[mesh_tab_base]
extends = esp32s3_base
board = mesh-tab
board_level = extra
board_upload.flash_size = 16MB
board_build.partitions = default_16MB.csv
upload_protocol = esptool
build_flags = ${esp32s3_base.build_flags}
-D MESH_TAB
-D CONFIG_ARDUHAL_ESP_LOG
-D CONFIG_ARDUHAL_LOG_COLORS=1
-D CONFIG_DISABLE_HAL_LOCKS=1
-D MESHTASTIC_EXCLUDE_CANNEDMESSAGES=1
-D MESHTASTIC_EXCLUDE_INPUTBROKER=1
-D MESHTASTIC_EXCLUDE_BLUETOOTH=1
-D MESHTASTIC_EXCLUDE_WEBSERVER=1
-D LV_LVGL_H_INCLUDE_SIMPLE
-D LV_CONF_INCLUDE_SIMPLE
-D LV_COMP_CONF_INCLUDE_SIMPLE
-D LV_USE_SYSMON=0
-D LV_USE_PROFILER=0
-D LV_USE_PERF_MONITOR=0
-D LV_USE_MEM_MONITOR=0
-D LV_USE_LOG=0
-D LV_BUILD_TEST=0
-D USE_LOG_DEBUG
-D LOG_DEBUG_INC=\"DebugConfiguration.h\"
-D RADIOLIB_SPI_PARANOID=0
-D HAS_SCREEN=0
-D HAS_TFT=1
-D USE_PIN_BUZZER
-D RAM_SIZE=1024
-D LGFX_DRIVER_TEMPLATE
-D LGFX_DRIVER=LGFX_GENERIC
-D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_GENERIC.h\"
-D LGFX_PIN_SCK=12
-D LGFX_PIN_MOSI=13
-D LGFX_PIN_MISO=11
-D LGFX_PIN_DC=16
-D LGFX_PIN_CS=10
-D LGFX_PIN_RST=-1
-D LGFX_PIN_BL=42
-D LGFX_TOUCH_INT=41
-D VIEW_320x240
-D USE_PACKET_API
-I variants/esp32s3/mesh-tab
build_src_filter = ${esp32s3_base.build_src_filter}
lib_deps =
${esp32s3_base.lib_deps}
${device-ui_base.lib_deps}
# renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
lovyan03/LovyanGFX@1.2.19
[mesh_tab_xpt2046]
extends = mesh_tab_base
build_flags = ${mesh_tab_base.build_flags}
-D LGFX_TOUCH=XPT2046
-D LGFX_TOUCH_SPI_FREQ=2500000
-D LGFX_TOUCH_SPI_HOST=2
-D LGFX_TOUCH_CS=7
-D LGFX_TOUCH_CLK=12
-D LGFX_TOUCH_DO=11
-D LGFX_TOUCH_DIN=13
-D LGFX_TOUCH_X_MIN=300
-D LGFX_TOUCH_X_MAX=3900
-D LGFX_TOUCH_Y_MIN=400
-D LGFX_TOUCH_Y_MAX=3900
[mesh_tab_ft5x06]
extends = mesh_tab_base
build_flags = ${mesh_tab_base.build_flags}
-D LGFX_TOUCH=FT5x06
-D LGFX_TOUCH_I2C_FREQ=400000
-D LGFX_TOUCH_I2C_PORT=0
-D LGFX_TOUCH_I2C_ADDR=0x38
-D LGFX_TOUCH_I2C_SDA=8
-D LGFX_TOUCH_I2C_SCL=9
-D LGFX_TOUCH_RST=7
; 3.2" TN TFT ST7789 / XPT2046: https://vi.aliexpress.com/item/1005005933490544.html
[env:mesh-tab-3-2-TN-resistive]
extends = mesh_tab_base
build_flags = ${mesh_tab_xpt2046.build_flags}
-D SPI_FREQUENCY=60000000
-D LGFX_SCREEN_WIDTH=240
-D LGFX_SCREEN_HEIGHT=320
-D DISPLAY_SIZE=320x240 ; landscape mode
-D LGFX_PANEL=ST7789
-D LGFX_INVERT_COLOR=false
-D LGFX_ROTATION=3
-D LGFX_TOUCH_ROTATION=4
; 3.2" IPS TFT ILI9341 / XPT2046: https://www.aliexpress.com/item/1005006258575617.html
[env:mesh-tab-3-2-IPS-resistive]
extends = mesh_tab_base
build_flags = ${mesh_tab_xpt2046.build_flags}
-D SPI_FREQUENCY=60000000 ; if image is distorted then lower to 40 MHz
-D LGFX_SCREEN_WIDTH=240
-D LGFX_SCREEN_HEIGHT=320
-D DISPLAY_SIZE=320x240 ; landscape mode
-D LGFX_PANEL=ILI9341
-D LGFX_ROTATION=1
-D LGFX_TOUCH_ROTATION=4
; 3.5" IPS TFT ILI9488 / XPT2046: https://vi.aliexpress.com/item/1005006333922639.html
[env:mesh-tab-3-5-IPS-resistive]
extends = mesh_tab_base
build_flags = ${mesh_tab_xpt2046.build_flags}
-D SPI_FREQUENCY=60000000 ; may go higher upto 40/60/80 MHz
-D DISPLAY_SET_RESOLUTION
-D LGFX_SCREEN_WIDTH=320
-D LGFX_SCREEN_HEIGHT=480
-D DISPLAY_SIZE=320x480 ; portrait mode
-D LGFX_PANEL=ILI9488
-D LGFX_ROTATION=0
-D LGFX_TOUCH_ROTATION=0
; 3.5" TN TFT ILI9488 / XPT2046: https://vi.aliexpress.com/item/32985467436.html
[env:mesh-tab-3-5-TN-resistive]
extends = mesh_tab_base
build_flags = ${mesh_tab_xpt2046.build_flags}
-D SPI_FREQUENCY=60000000
-D DISPLAY_SET_RESOLUTION
-D LGFX_SCREEN_WIDTH=320
-D LGFX_SCREEN_HEIGHT=480
-D DISPLAY_SIZE=320x480 ; portrait mode
-D LGFX_PANEL=HX8357B
-D LGFX_INVERT_COLOR=false
-D LGFX_ROTATION=4
-D LGFX_TOUCH_ROTATION=2
; 3.2" IPS TFT ILI9341 / FT6236: https://vi.aliexpress.com/item/1005006624072350.html
[env:mesh-tab-3-2-IPS-capacitive]
extends = mesh_tab_base
build_flags = ${mesh_tab_ft5x06.build_flags}
-D SPI_FREQUENCY=75000000 ; may go higher upto 60/80 MHz
-D LGFX_SCREEN_WIDTH=240
-D LGFX_SCREEN_HEIGHT=320
-D DISPLAY_SIZE=320x240 ; landscape mode
-D LGFX_PANEL=ILI9341
-D LGFX_ROTATION=1
-D LGFX_TOUCH_X_MIN=0
-D LGFX_TOUCH_X_MAX=239
-D LGFX_TOUCH_Y_MIN=0
-D LGFX_TOUCH_Y_MAX=319
-D LGFX_TOUCH_ROTATION=2
; 3.5" IPS TFT ILI9488 / FT6236: https://vi.aliexpress.com/item/1005006893699919.html
[env:mesh-tab-3-5-IPS-capacitive]
extends = mesh_tab_base
build_flags = ${mesh_tab_ft5x06.build_flags}
-D SPI_FREQUENCY=75000000 ; may go higher upto 40/60/80 MHz
-D DISPLAY_SET_RESOLUTION
-D LGFX_SCREEN_WIDTH=320
-D LGFX_SCREEN_HEIGHT=480
-D DISPLAY_SIZE=320x480 ; portrait mode
-D LGFX_PANEL=ILI9488
-D LGFX_ROTATION=2
-D LGFX_TOUCH_X_MIN=0
-D LGFX_TOUCH_X_MAX=319
-D LGFX_TOUCH_Y_MIN=0
-D LGFX_TOUCH_Y_MAX=479
-D LGFX_TOUCH_ROTATION=0
; 4.0" IPS TFT ILI9488 / FT6236: https://vi.aliexpress.com/item/1005007082906950.html
[env:mesh-tab-4-0-IPS-capacitive]
extends = mesh_tab_base
build_flags = ${mesh_tab_ft5x06.build_flags}
-D SPI_FREQUENCY=75000000
-D DISPLAY_SET_RESOLUTION
-D LGFX_SCREEN_WIDTH=320
-D LGFX_SCREEN_HEIGHT=480
-D DISPLAY_SIZE=320x480 ; portrait mode
-D LGFX_PANEL=HX8357B
-D LGFX_ROTATION=4
-D LGFX_TOUCH_X_MIN=0
-D LGFX_TOUCH_X_MAX=319
-D LGFX_TOUCH_Y_MIN=0
-D LGFX_TOUCH_Y_MAX=479
-D LGFX_TOUCH_ROTATION=6
code/firmware/variants/esp32s3/mesh-tab/variant.h
+60
View File
@@ -0,0 +1,60 @@
#ifndef _VARIANT_MESHTAB_DIY_
#define _VARIANT_MESHTAB_DIY_
#define HAS_TOUCHSCREEN 1
#define USE_POWERSAVE
#define SLEEP_TIME 180
// Analog pins
#define BATTERY_PIN 4 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
// ratio of voltage divider (100k, 220k)
#define ADC_MULTIPLIER 1.6 // 1.45 + 10% for correction of display undervoltage.
#define ADC_CHANNEL ADC1_GPIO4_CHANNEL
// LED
#define LED_POWER 21
// Button
#define BUTTON_PIN 0
// Button
#define PIN_BUZZER 5
// GPS
#define GPS_RX_PIN 18
#define GPS_TX_PIN 17
// #define HAS_SDCARD 1
#define SPI_MOSI 13
#define SPI_SCK 12
#define SPI_MISO 11
#define SPI_CS 10
#define SDCARD_CS 6
// LORA MODULES
#define USE_SX1262
// LORA SPI
#define LORA_SCK 36
#define LORA_MISO 37
#define LORA_MOSI 35
#define LORA_CS 39
// LORA CONFIG
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 14
#define LORA_DIO1 15 // SX1262 IRQ
#define LORA_DIO2 40 // SX1262 BUSY
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET 14
#define SX126X_RXEN 47
#define SX126X_TXEN RADIOLIB_NC // Assuming that DIO2 is connected to TXEN pin
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#endif
code/firmware/variants/esp32s3/mini-epaper-s3/pins_arduino.h
+26
View File
@@ -0,0 +1,26 @@
#ifndef Pins_Arduino_h
#define Pins_Arduino_h
#include <stdint.h>
#define USB_VID 0x303a
#define USB_PID 0x1001
// The default Wire will be mapped to PMU and RTC
static const uint8_t SDA = 18;
static const uint8_t SCL = 9;
// Default SPI will be mapped to Radio
static const uint8_t SS = -1;
static const uint8_t MOSI = 17;
static const uint8_t MISO = 6;
static const uint8_t SCK = 8;
#define SPI_MOSI (39)
#define SPI_SCK (41)
#define SPI_MISO (38)
#define SPI_CS (40)
#define SDCARD_CS SPI_CS
#endif /* Pins_Arduino_h */
code/firmware/variants/esp32s3/mini-epaper-s3/platformio.ini
+31
View File
@@ -0,0 +1,31 @@
[env:mini-epaper-s3]
;custom_meshtastic_hw_model =
custom_meshtastic_hw_model_slug = MINI_EPAPER_S3
custom_meshtastic_architecture = esp32-s3
custom_meshtastic_actively_supported = true
custom_meshtastic_support_level = 1
custom_meshtastic_display_name = LILYGO Mini ePaper S3 E-Ink
custom_meshtastic_images = mini-epaper-s3.svg
custom_meshtastic_tags = LilyGo
custom_meshtastic_requires_dfu = no
extends = esp32s3_base
board = mini-epaper-s3
board_check = true
upload_protocol = esptool
build_flags =
${esp32s3_base.build_flags}
-I variants/esp32s3/mini-epaper-s3
-DMINI_EPAPER_S3
-DUSE_EINK
-DEINK_DISPLAY_MODEL=GxEPD2_102
-DEINK_WIDTH=128
-DEINK_HEIGHT=80
lib_deps =
${esp32s3_base.lib_deps}
# renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
https://github.com/meshtastic/GxEPD2/archive/c7eb4c3c167cf396ef4f541cc5d4c6aa42f3c46b.zip
# renovate: datasource=custom.pio depName=SensorLib packageName=lewisxhe/library/SensorLib
lewisxhe/SensorLib@0.3.4
code/firmware/variants/esp32s3/mini-epaper-s3/variant.h
+57
View File
@@ -0,0 +1,57 @@
// Display (E-Ink)
#define PIN_EINK_CS 13
#define PIN_EINK_BUSY 10
#define PIN_EINK_RES 11
#define PIN_EINK_SCLK 14
#define PIN_EINK_MOSI 15
#define PIN_EINK_DC 12
#define PIN_EINK_EN 42
#define SPI_INTERFACES_COUNT 2
#define PIN_SPI1_MISO -1
#define PIN_SPI1_MOSI PIN_EINK_MOSI
#define PIN_SPI1_SCK PIN_EINK_SCLK
#define DISPLAY_FORCE_SMALL_FONTS
#define I2C_SDA SDA
#define I2C_SCL SCL
#define BATTERY_PIN 2 // A battery voltage measurement pin, voltage divider connected here to
// measure battery voltage ratio of voltage divider = 2.0 (assumption)
#define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
#define ADC_CHANNEL ADC1_GPIO2_CHANNEL
#define HAS_GPS 0
#undef GPS_RX_PIN
#undef GPS_TX_PIN
#define BUTTON_PIN 3
#define BUTTON_NEED_PULLUP
#define ALT_BUTTON_PIN 4
#define ALT_BUTTON_ACTIVE_LOW true
#define ALT_BUTTON_ACTIVE_PULLUP true
#define PIN_BUTTON3 0
// #define HAS_SDCARD 1
// #define SDCARD_USE_SOFT_SPI
// PCF85063 RTC Module
#define PCF85063_RTC 0x51
#define HAS_RTC 1
#define USE_SX1262
#define LORA_DIO1 5
#define LORA_SCK 8
#define LORA_MISO 6
#define LORA_MOSI 17
#define LORA_CS 7 // CS not connected; IO7 is free
#define LORA_RESET 21
#ifdef USE_SX1262
#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY 16
#define SX126X_RESET LORA_RESET
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#endif

Some files were not shown because too many files have changed in this diff Show More