Signed-off-by: 吴文峰 <kevin@lmve.net>

2026-03-03 22:16:00 +08:00
parent 7ae6e9e999
commit 88d56e1e9e
1660 changed files with 281430 additions and 0 deletions
@@ -0,0 +1,31 @@
+[env:dreamcatcher] ; 2301, latest revision
+extends = esp32s3_base
+board = esp32s3box
+board_build.partitions = default_16MB.csv
+board_level = extra
+
+build_flags = 
+  ${esp32s3_base.build_flags}
+  -D PRIVATE_HW
+  -D OTHERNET_DC_REV=2301
+  -I variants/esp32s3/dreamcatcher
+  -D ARDUINO_USB_CDC_ON_BOOT=1
+
+lib_deps = ${esp32s3_base.lib_deps}
+  # renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
+  earlephilhower/ESP8266Audio@1.9.9
+  # renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
+  earlephilhower/ESP8266SAM@1.1.0
+
+[env:dreamcatcher-2206] 
+extends = esp32s3_base
+board = esp32s3box
+board_build.partitions = default_16MB.csv
+board_level = extra
+
+build_flags = 
+  ${esp32s3_base.build_flags}
+  -D PRIVATE_HW
+  -D OTHERNET_DC_REV=2206
+  -I variants/esp32s3/dreamcatcher
+  -D ARDUINO_USB_CDC_ON_BOOT=1
@@ -0,0 +1,17 @@
+#include "RadioLib.h"
+
+// RF Switch Matrix SubG RFO_HP_LF / RFO_LP_LF / RFI_[NP]_LF0
+// DIO5 -> RFSW0_V1
+// DIO6 -> RFSW1_V2
+// DIO7 -> ANT_CTRL_ON + ESP_IO9/LR_GPS_ANT_DC_EN -> RFI_GPS (Bias-T GPS)
+
+static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_LR11X0_DIO7, RADIOLIB_NC,
+                                             RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[] = {
+    // mode                  DIO5  DIO6  DIO7
+    {LR11x0::MODE_STBY, {LOW, LOW, LOW}},  {LR11x0::MODE_RX, {HIGH, LOW, LOW}},
+    {LR11x0::MODE_TX, {LOW, HIGH, LOW}},   {LR11x0::MODE_TX_HP, {LOW, HIGH, LOW}},
+    {LR11x0::MODE_TX_HF, {LOW, LOW, LOW}}, {LR11x0::MODE_GNSS, {LOW, LOW, HIGH}},
+    {LR11x0::MODE_WIFI, {LOW, LOW, LOW}},  END_OF_MODE_TABLE,
+};
@@ -0,0 +1,110 @@
+#undef I2C_SDA
+#undef I2C_SCL
+#define I2C_SDA 16 // I2C pins for this board
+#define I2C_SCL 17
+
+#define I2C_SDA1 45
+#define I2C_SCL1 46
+
+#define LED_POWER 6
+#define LED_STATE_ON 1
+#define BUTTON_PIN 0
+
+#define HAS_TPS65233
+
+// V1 of SubG Switch SMA 0 or F Selector 1
+// #define RF_SW_SUBG1 8
+// V2 of SubG Switch SMA 1 or F Selector 0
+// #define RF_SW_SUBG2 5
+
+#define RESET_OLED 8 // Emulate RF_SW_SUBG1, Use F Connector
+#define VTFT_CTRL 5  // Emulate RF_SW_SUBG2, for SMA swap the pin values
+
+#if OTHERNET_DC_REV == 2206
+#define USE_LR1120
+
+#define SPI_MISO 37
+#define SPI_MOSI 39
+#define SPI_SCK 38
+#define SDCARD_CS 40
+
+#define PIN_BUZZER 48
+
+// These can either be used for GPS or a serial link. Define through Protobufs
+// #define GPS_RX_PIN 10
+// #define GPS_TX_PIN 21
+
+#define PIN_POWER_EN 7            // RF section power supply enable
+#define PERIPHERAL_WARMUP_MS 1000 // wait for TPS chip to initialize
+#define TPS_EXTM 45               // connected, but not used
+#define BIAS_T_ENABLE 9           // needs to be low
+#define BIAS_T_VALUE 0
+#else // 2301
+#define USE_LR1121
+#define SPI_MISO 10
+#define SPI_MOSI 39
+#define SPI_SCK 38
+
+#define SDCARD_CS 40
+
+// This is only informational, we always use SD cards in 1 bit mode
+#define SPI_DATA1 15
+#define SPI_DATA2 18
+
+// These can either be used for GPS or a serial link. Define through Protobufs
+// #define GPS_RX_PIN 36
+// #define GPS_TX_PIN 37
+
+// dac / amp instead of buzzer
+#define HAS_I2S
+#define DAC_I2S_BCK 21
+#define DAC_I2S_WS 9
+#define DAC_I2S_DOUT 48
+#define DAC_I2S_MCLK 44
+
+#define BIAS_T_ENABLE 7 // needs to be low
+#define BIAS_T_VALUE 0
+#define BIAS_T_SUBGHZ 2 // also needs to be low, we hijack SENSOR_POWER_CTRL_PIN to emulate this
+#define SENSOR_POWER_CTRL_PIN BIAS_T_SUBGHZ
+#define SENSOR_POWER_ON 0
+#endif
+
+#define HAS_SDCARD // Have SPI interface SD card slot
+#define SDCARD_USE_SPI1
+
+#define LORA_RESET 3
+#define LORA_SCK 12
+#define LORA_MISO 13
+#define LORA_MOSI 11
+#define LORA_CS 14
+#define LORA_DIO9 4
+#define LORA_DIO2 47
+
+#define LR1120_IRQ_PIN LORA_DIO9
+#define LR1120_NRESET_PIN LORA_RESET
+#define LR1120_BUSY_PIN LORA_DIO2
+#define LR1120_SPI_NSS_PIN LORA_CS
+#define LR1120_SPI_SCK_PIN LORA_SCK
+#define LR1120_SPI_MOSI_PIN LORA_MOSI
+#define LR1120_SPI_MISO_PIN LORA_MISO
+
+#define LR1121_IRQ_PIN LORA_DIO9
+#define LR1121_NRESET_PIN LORA_RESET
+#define LR1121_BUSY_PIN LORA_DIO2
+#define LR1121_SPI_NSS_PIN LORA_CS
+#define LR1121_SPI_SCK_PIN LORA_SCK
+#define LR1121_SPI_MOSI_PIN LORA_MOSI
+#define LR1121_SPI_MISO_PIN LORA_MISO
+
+#define LR11X0_DIO3_TCXO_VOLTAGE 1.8
+#define LR11X0_DIO_AS_RF_SWITCH
+
+// This board needs external switching between sub-GHz and 2.4G circuits
+
+// V1 of RF1 selector SubG 1 or 2.4GHz 0
+// #define RF_SW_SMA1 42
+// V2 of RF1 Selector SubG 0 or 2.4GHz 1
+// #define RF_SW_SMA2 41
+
+#define LR11X0_RF_SWITCH_SUBGHZ 42
+#define LR11X0_RF_SWITCH_2_4GHZ 41