Signed-off-by: 吴文峰 <kevin@lmve.net>

2026-03-03 22:16:00 +08:00
parent 7ae6e9e999
commit 88d56e1e9e
1660 changed files with 281430 additions and 0 deletions
@@ -0,0 +1,20 @@
+[env:CDEBYTE_E77-MBL]
+extends = stm32_base
+board = ebyte_e77_dev
+board_upload.maximum_size = 233472 ; reserve the last 28KB for filesystem
+board_level = extra
+build_flags =
+  ${stm32_base.build_flags}
+  -Ivariants/stm32/CDEBYTE_E77-MBL
+  -DSERIAL_UART_INSTANCE=2
+  -DPIN_SERIAL_RX=PA3
+  -DPIN_SERIAL_TX=PA2
+  -DENABLE_HWSERIAL1
+  -DPIN_SERIAL1_RX=PB7
+  -DPIN_SERIAL1_TX=PB6
+  -DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
+  -DMESHTASTIC_EXCLUDE_AIR_QUALITY_SENSOR=1
+  -DMESHTASTIC_EXCLUDE_I2C=1
+  -DMESHTASTIC_EXCLUDE_GPS=1
+
+upload_port = stlink
@@ -0,0 +1,9 @@
+// From E77-900M22S Product Specification
+// https://www.cdebyte.com/pdf-down.aspx?id=2963
+// Note 1: PA6 and PA7 pins are used as internal control RF switches of the module, PA6 = RF_TXEN, PA7 = RF_RXEN, RF_TXEN=1
+// RF_RXEN=0 is the transmit channel, and RF_TXEN=0 RF_RXEN=1 is the receiving channel
+
+static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PA7, PA6, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[4] = {
+    {STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
@@ -0,0 +1,25 @@
+/*
+EByte E77-MBL series
+https://www.cdebyte.com/products/E77-900MBL-01
+https://www.cdebyte.com/products/E77-400MBL-01
+https://github.com/olliw42/mLRS-docu/blob/master/docs/EBYTE_E77_MBL.md
+*/
+
+/*
+This variant is a work in progress.
+Do not expect a working Meshtastic device with this target.
+*/
+
+#ifndef _VARIANT_EBYTE_E77_
+#define _VARIANT_EBYTE_E77_
+
+#define USE_STM32WLx
+
+#define LED_POWER PB4 // LED1
+// #define LED_POWER PB3 // LED2
+#define LED_STATE_ON 1
+
+#define SERIAL_PRINT_PORT 1
+
+#define EBYTE_E77_MBL
+#endif
@@ -0,0 +1,24 @@
+; Milesight GS301 Bathroom Odor Detector
+; https://www.milesight.com/iot/product/lorawan-sensor/gs301
+[env:milesight_gs301]
+extends = stm32_base
+board = wiscore_rak3172 ; Convenient choice as the same USART is used for programming/debug
+board_level = extra
+board_upload.maximum_size = 233472 ; reserve the last 28KB for filesystem
+build_flags =
+  ${stm32_base.build_flags}
+  -Ivariants/stm32/milesight_gs301
+  -DPRIVATE_HW
+  -DMESHTASTIC_EXCLUDE_GPS=1
+  -DMESHTASTIC_EXCLUDE_I2C=1 # Analog ADuCM355 (unsupported) so no point building support for I2C in
+  -DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
+  -DMESHTASTIC_EXCLUDE_AIR_QUALITY_SENSOR=1
+build_unflags =
+  -DDEBUG_MUTE # We have space for debug output until sensor support is added
+build_src_filter =
+  ${stm32_base.build_src_filter}
+  +<../variants/stm32/milesight_gs301>
+lib_deps =
+  ${stm32_base.lib_deps}
+
+upload_port = stlink
@@ -0,0 +1,7 @@
+// Seems to use the same RF switch pins as RAK3172… getting Tx/Rx SNR +11dB with a nearby node
+// PB8, PC13
+
+static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PB8, PC13, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[4] = {
+    {STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
@@ -0,0 +1,8 @@
+#include "variant.h"
+#include "Arduino.h"
+
+void earlyInitVariant()
+{
+    pinMode(USER_LED, OUTPUT);
+    digitalWrite(USER_LED, HIGH ^ LED_STATE_ON);
+}
@@ -0,0 +1,41 @@
+#ifndef _VARIANT_MILESIGHT_GS301_
+#define _VARIANT_MILESIGHT_GS301_
+
+#define USE_STM32WLx
+
+// I/O
+#define LED_STATE_ON 1
+#define PIN_LED1 PA0 // Green LED
+#define LED_POWER PIN_LED1
+#define PIN_LED2 PA0 // Red LED
+#define USER_LED PIN_LED2
+#define BUTTON_PIN PC13
+#define BUTTON_ACTIVE_LOW true
+#define BUTTON_ACTIVE_PULLUP false
+#define PIN_BUZZER PA6
+
+// EC Sense DGM10 Double Gas Module
+// Analog ADuCM355 (unsupported); SHTC3 is connected to ADuCM355 and not directly accessible
+#define PIN_WIRE_SDA PB7
+#define PIN_WIRE_SCL PB8
+// Commented out to keep sensor powered down due to lack of support
+/*
+#define VEXT_ENABLE PB12 // TI TPS61291DRV VSEL - set LOW before ENable for Vout = 3.3V
+#define VEXT_ON_VALUE LOW
+#define SENSOR_POWER_CTRL_PIN PB2 // TI TPS61291DRV EN pin
+#define SENSOR_POWER_ON HIGH
+#define HAS_SENSOR 1
+*/
+
+#define ENABLE_HWSERIAL1
+#define PIN_SERIAL1_RX NC
+#define PIN_SERIAL1_TX PB6
+
+// LoRa
+#define SX126X_DIO3_TCXO_VOLTAGE 3.0
+
+// Required to avoid Serial1 conflicts due to board definition here:
+// https://github.com/stm32duino/Arduino_Core_STM32/blob/main/variants/STM32WLxx/WL54CCU_WL55CCU_WLE4C(8-B-C)U_WLE5C(8-B-C)U/variant_RAK3172_MODULE.h
+#define RAK3172
+
+#endif
@@ -0,0 +1,19 @@
+[env:rak3172]
+extends = stm32_base
+board = wiscore_rak3172
+board_level = pr
+board_upload.maximum_size = 233472 ; reserve the last 28KB for filesystem
+build_flags =
+  ${stm32_base.build_flags}
+  -Ivariants/stm32/rak3172
+  -DENABLE_HWSERIAL1
+  -DPIN_SERIAL1_RX=PB7
+  -DPIN_SERIAL1_TX=PB6
+  -DPIN_WIRE_SDA=PA11
+  -DPIN_WIRE_SCL=PA12
+  -DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
+  -DMESHTASTIC_EXCLUDE_AIR_QUALITY_SENSOR=1
+  -DMESHTASTIC_EXCLUDE_I2C=1
+  -DMESHTASTIC_EXCLUDE_GPS=1
+
+upload_port = stlink
@@ -0,0 +1,7 @@
+// Pins from https://forum.rakwireless.com/t/rak3172-internal-schematic/4557/2
+// PB8, PC13
+
+static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PB8, PC13, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[4] = {
+    {STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
@@ -0,0 +1,22 @@
+/*
+STM32WLE5 Core Module for LoRaWAN® RAK3372
+https://store.rakwireless.com/products/wisblock-core-module-rak3372
+*/
+
+/*
+This variant is a work in progress.
+Do not expect a working Meshtastic device with this target.
+*/
+
+#ifndef _VARIANT_RAK3172_
+#define _VARIANT_RAK3172_
+
+#define USE_STM32WLx
+
+#define LED_POWER PA0 // Green LED
+#define LED_STATE_ON 1
+
+#define RAK3172
+#define SERIAL_PRINT_PORT 1
+
+#endif
@@ -0,0 +1,21 @@
+; Russell is a board designed to mount on an ER34615/IFR32700 cell and go Up! on a balloon
+; Hardware repository: https://github.com/Meshtastic-Malaysia/russell
+; - RAK3172 STM32WLE5CCU6 MCU + integrated SX1262 LoRa
+; - CDtop CD-PA1010D GPS
+; - Bosch Sensortec BME280 sensor
+; - Consonance CN3158 LiFePO4 solar charger
+[env:russell]
+extends = stm32_base
+board = wiscore_rak3172
+board_level = extra
+board_upload.maximum_size = 233472 ; reserve the last 28KB for filesystem
+build_flags =
+  ${stm32_base.build_flags}
+  -Ivariants/stm32/russell
+  -DPRIVATE_HW
+lib_deps =
+  ${stm32_base.lib_deps}
+	# renovate: datasource=custom.pio depName=Adafruit BME280 packageName=adafruit/library/Adafruit BME280 Library
+	adafruit/Adafruit BME280 Library@2.3.0
+
+upload_port = stlink
@@ -0,0 +1,7 @@
+// Pins from https://forum.rakwireless.com/t/rak3172-internal-schematic/4557/2
+// PB8, PC13
+
+static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PB8, PC13, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[4] = {
+    {STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
@@ -0,0 +1,41 @@
+#ifndef _VARIANT_RUSSELL_
+#define _VARIANT_RUSSELL_
+
+#define USE_STM32WLx
+
+// I/O
+#define LED_POWER PA0 // Red LED
+#define LED_STATE_ON 1
+#define BUTTON_PIN PH3 // Shared with BOOT0
+#define BUTTON_NEED_PULLUP
+// Charger IC charge/standby pins are open-drain with no hardware pull-up:
+// Internal pull-up is needed on STM32 (TODO)
+// #define EXT_CHRG_DETECT PA5
+// #define EXT_PWR_DETECT PA4
+
+// Bosch Sensortec BME280
+#define HAS_SENSOR 1
+
+// CDtop CD-PA1010D
+#define ENABLE_HWSERIAL1
+#define PIN_SERIAL1_RX PB7
+#define PIN_SERIAL1_TX PB6
+#define HAS_GPS 1
+#define PIN_GPS_STANDBY PA15
+#define GPS_RX_PIN PB7
+#define GPS_TX_PIN PB6
+
+// LoRa
+/*
+ * RAK3172   (-20–85°C) -> No TCXO
+ * RAK3172-T (-40–85°C) -> 3.0V TCXO
+ * https://github.com/RAKWireless/RAK-STM32-RUI/blob/e5a28be8fab1a492bd9223dd425ca33a8a297d90/variants/WisDuo_RAK3172-T_Board/radio_conf.h#L91
+ */
+#define TCXO_OPTIONAL
+#define SX126X_DIO3_TCXO_VOLTAGE 3.0
+
+// Required to avoid Serial1 conflicts due to board definition here:
+// https://github.com/stm32duino/Arduino_Core_STM32/blob/main/variants/STM32WLxx/WL54CCU_WL55CCU_WLE4C(8-B-C)U_WLE5C(8-B-C)U/variant_RAK3172_MODULE.h
+#define RAK3172
+
+#endif
@@ -0,0 +1,58 @@
+[stm32_base]
+extends = arduino_base
+platform =
+  # renovate: datasource=custom.pio depName=platformio/ststm32 packageName=platformio/platform/ststm32
+  platformio/ststm32@19.5.0
+platform_packages =
+  # renovate: datasource=github-tags depName=Arduino_Core_STM32 packageName=stm32duino/Arduino_Core_STM32
+  platformio/framework-arduinoststm32@https://github.com/stm32duino/Arduino_Core_STM32/archive/2.10.1.zip
+extra_scripts =
+  ${env.extra_scripts}
+  extra_scripts/stm32_extra.py
+
+build_type = release
+
+build_flags =
+  ${arduino_base.build_flags}
+  -flto
+  -Isrc/platform/stm32wl -g
+  -DMESHTASTIC_EXCLUDE_AUDIO=1
+  -DMESHTASTIC_EXCLUDE_ATAK=1 ; ATAK is quite big, disable it for big flash savings.
+  -DMESHTASTIC_EXCLUDE_INPUTBROKER=1
+  -DMESHTASTIC_EXCLUDE_POWERMON=1
+  -DMESHTASTIC_EXCLUDE_SCREEN=1
+  -DMESHTASTIC_EXCLUDE_MQTT=1
+  -DMESHTASTIC_EXCLUDE_BLUETOOTH=1
+  -DMESHTASTIC_EXCLUDE_WIFI=1
+  -DMESHTASTIC_EXCLUDE_TZ=1 ; Exclude TZ to save some flash space.
+  -DSERIAL_RX_BUFFER_SIZE=256 ; For GPS - the default of 64 is too small.
+  -DHAS_SCREEN=0 ; Always disable screen for STM32, it is not supported.
+  -DPIO_FRAMEWORK_ARDUINO_NANOLIB_FLOAT_PRINTF ; This is REQUIRED for at least traceroute debug prints - without it the length ends up uninitialized.
+  -DDEBUG_MUTE ; You can #undef DEBUG_MUTE in certain source files if you need the logs.
+  -fmerge-all-constants
+  -ffunction-sections
+  -fdata-sections
+  -DRADIOLIB_EXCLUDE_SX128X=1
+  -DRADIOLIB_EXCLUDE_SX127X=1
+  -DRADIOLIB_EXCLUDE_LR11X0=1
+  -DHAL_DAC_MODULE_ONLY
+  -DHAL_RNG_MODULE_ENABLED
+  -Wl,--wrap=__assert_func
+  -Wl,--wrap=strerror
+  -Wl,--wrap=_tzset_unlocked_r
+
+build_src_filter =
+  ${arduino_base.build_src_filter} -<platform/esp32/> -<nimble/> -<mesh/api/> -<mesh/wifi/> -<mesh/http/> -<modules/esp32> -<mesh/eth/> -<input> -<buzz> -<modules/RemoteHardwareModule.cpp> -<platform/nrf52> -<platform/portduino> -<platform/rp2xx0> -<mesh/raspihttp>
+
+board_upload.offset_address = 0x08000000
+upload_protocol = stlink
+debug_tool = stlink
+
+lib_deps =
+  ${env.lib_deps}
+  ${radiolib_base.lib_deps}
+  # renovate: datasource=git-refs depName=caveman99-stm32-Crypto packageName=https://github.com/caveman99/Crypto gitBranch=main
+  https://github.com/caveman99/Crypto/archive/1aa30eb536bd52a576fde6dfa393bf7349cf102d.zip
+
+lib_ignore =
+  OneButton
@@ -0,0 +1,22 @@
+[env:wio-e5]
+extends = stm32_base
+board = lora_e5_dev_board
+board_level = pr
+board_upload.maximum_size = 233472 ; reserve the last 28KB for filesystem
+build_flags =
+  ${stm32_base.build_flags}
+  -Ivariants/stm32/wio-e5
+  -DSERIAL_UART_INSTANCE=1
+  -DPIN_SERIAL_RX=PB7
+  -DPIN_SERIAL_TX=PB6
+  -DPIN_WIRE_SDA=PA15
+  -DPIN_WIRE_SCL=PB15
+  -DHAS_SENSOR=1
+  -DENABLE_HWSERIAL2
+  -DPIN_SERIAL2_TX=PA2
+  -DPIN_SERIAL2_RX=PA3
+  -DHAS_GPS=1
+  -DGPS_SERIAL_PORT=Serial2
+  -DMESHTASTIC_EXCLUDE_AIR_QUALITY_SENSOR=1
+
+upload_port = stlink
@@ -0,0 +1,8 @@
+/* https://wiki.seeedstudio.com/LoRa-E5_STM32WLE5JC_Module/
+ * Wio-E5 module ONLY transmits through RFO_HP
+ * Receive: PA4=1, PA5=0
+ * Transmit(high output power, SMPS mode): PA4=0, PA5=1 */
+static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PA4, PA5, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[4] = {
+    {STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
@@ -0,0 +1,22 @@
+/*
+Wio-E5 mini (formerly LoRa-E5 mini)
+https://www.seeedstudio.com/LoRa-E5-mini-STM32WLE5JC-p-4869.html
+https://www.seeedstudio.com/LoRa-E5-Wireless-Module-p-4745.html
+*/
+
+/*
+This variant is a work in progress.
+Do not expect a working Meshtastic device with this target.
+*/
+
+#ifndef _VARIANT_WIOE5_
+#define _VARIANT_WIOE5_
+
+#define USE_STM32WLx
+
+#define LED_POWER PB5
+#define LED_STATE_ON 0
+
+#define WIO_E5
+
+#endif