Signed-off-by: 吴文峰 <kevin@lmve.net>

2026-03-06 16:29:48 +08:00
parent afdd525324
commit ff19e9c6a4
3110 changed files with 8 additions and 523962 deletions
@@ -1,28 +0,0 @@
-// Need this file for ESP32-S3
-// No need to modify this file, changes to pins imported from variant.h
-// Most is similar to https://github.com/espressif/arduino-esp32/blob/master/variants/esp32s3/pins_arduino.h
-
-#ifndef Pins_Arduino_h
-#define Pins_Arduino_h
-
-#include <stdint.h>
-#include <variant.h>
-
-#define USB_VID 0x303a
-#define USB_PID 0x1001
-
-// Serial
-static const uint8_t TX = UART_TX;
-static const uint8_t RX = UART_RX;
-
-// Default SPI will be mapped to Radio
-static const uint8_t SS = LORA_CS;
-static const uint8_t SCK = LORA_SCK;
-static const uint8_t MOSI = LORA_MOSI;
-static const uint8_t MISO = LORA_MISO;
-
-// The default Wire will be mapped to PMU and RTC
-static const uint8_t SCL = I2C_SCL;
-static const uint8_t SDA = I2C_SDA;
-
-#endif /* Pins_Arduino_h */
@@ -1,7 +0,0 @@
-[env:CDEBYTE_EoRa-S3]
-extends = esp32s3_base
-board = CDEBYTE_EoRa-S3
-build_flags =
-  ${esp32s3_base.build_flags}
-  -D CDEBYTE_EORA_S3
-  -I variants/esp32s3/CDEBYTE_EoRa-S3
@@ -1,63 +0,0 @@
-// LED - status indication
-#define LED_PIN 37
-
-// Button - user interface
-#define BUTTON_PIN 0 // This is the BOOT button, and it has its own pull-up resistor
-
-// SD card - TODO: test, currently untested, copied from T3S3 variant
-#define HAS_SDCARD
-#define SDCARD_USE_SPI1
-// TODO: rename this to make this SD-card specific
-#define SPI_CS 13
-#define SPI_SCK 14
-#define SPI_MOSI 11
-#define SPI_MISO 2
-// FIXME: there are two other SPI pins that are not defined here
-// Compatibility
-#define SDCARD_CS SPI_CS
-
-// Battery voltage monitoring - TODO: test, currently untested, copied from T3S3 variant
-#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
-#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
-#define ADC_MULTIPLIER                                                                                                           \
-    2.11 // ratio of voltage divider = 2.0 (R10=1M, R13=1M), plus some undervoltage correction - TODO: this was carried over from
-         // the T3S3, test to see if the undervoltage correction is needed.
-
-// Display - OLED connected via I2C by the default hardware configuration
-#define HAS_SCREEN 1
-#define USE_SSD1306
-#define I2C_SCL 17
-#define I2C_SDA 18
-
-// UART - The 1mm JST SH connector closest to the USB-C port
-#define UART_TX 43
-#define UART_RX 44
-
-// Peripheral I2C - The 1mm JST SH connector furthest from the USB-C port which follows Adafruit connection standard. There are no
-// pull-up resistors on these lines, the downstream device needs to include them. TODO: test, currently untested
-#define I2C_SCL1 21
-#define I2C_SDA1 10
-
-// Radio
-#define USE_SX1262 // CDEBYTE EoRa-S3-900TB <- CDEBYTE E22-900MM22S <- Semtech SX1262
-#define USE_SX1268 // CDEBYTE EoRa-S3-400TB <- CDEBYTE E22-400MM22S <- Semtech SX1268
-
-#define SX126X_CS 7
-#define LORA_SCK 5
-#define LORA_MOSI 6
-#define LORA_MISO 3
-#define SX126X_RESET 8
-#define SX126X_BUSY 34
-#define SX126X_DIO1 33
-
-#define SX126X_DIO2_AS_RF_SWITCH // All switching is performed with DIO2, it is automatically inverted using circuitry.
-// CDEBYTE EoRa-S3 uses an XTAL, thus we do not need DIO3 as TCXO voltage reference. Don't define SX126X_DIO3_TCXO_VOLTAGE for
-// simplicity rather than defining it as 0.
-#define SX126X_MAX_POWER                                                                                                         \
-    22 // E22-900MM22S and E22-400MM22S have a raw SX1262 or SX1268 respsectively, they are rated to output up and including 22
-       // dBm out of their SX126x IC.
-
-// Compatibility with old variant.h file structure - FIXME: this should be done in the respective radio interface modules to clean
-// up all variants.
-#define LORA_CS SX126X_CS
-#define LORA_DIO1 SX126X_DIO1