Signed-off-by: 吴文峰 <kevin@lmve.net>

2026-03-06 16:29:48 +08:00
parent afdd525324
commit ff19e9c6a4
3110 changed files with 8 additions and 523962 deletions
@@ -1,26 +0,0 @@
-#ifndef Pins_Arduino_h
-#define Pins_Arduino_h
-
-#include <stdint.h>
-
-#define USB_VID 0x303a
-#define USB_PID 0x1001
-
-// The default Wire will be mapped to PMU and RTC
-static const uint8_t SDA = 17;
-static const uint8_t SCL = 18;
-
-// Default SPI will be mapped to Radio
-static const uint8_t SS = 40;
-static const uint8_t MOSI = 11;
-static const uint8_t MISO = 9;
-static const uint8_t SCK = 10;
-
-#define SPI_MOSI (11)
-#define SPI_SCK (10)
-#define SPI_MISO (9)
-#define SPI_CS (12)
-
-#define SDCARD_CS SPI_CS
-
-#endif /* Pins_Arduino_h */
@@ -1,18 +0,0 @@
-[env:t-eth-elite]
-extends = esp32s3_base
-board = esp32s3box
-board_level = pr
-board_check = true
-board_build.partitions = default_16MB.csv
-build_flags = 
-  ${esp32s3_base.build_flags}
-  -D T_ETH_ELITE
-  -D HAS_UDP_MULTICAST=1
-  -I variants/esp32s3/t-eth-elite
-
-lib_ignore = 
-    Ethernet
-
-lib_deps = 
-  ${esp32s3_base.lib_deps}
-  https://github.com/meshtastic/ETHClass2/archive/v1.0.0.zip
@@ -1,11 +0,0 @@
-#include "RadioLib.h"
-
-static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
-
-static const Module::RfSwitchMode_t rfswitch_table[] = {
-    // mode                  DIO5  DIO6
-    {LR11x0::MODE_STBY, {LOW, LOW}},  {LR11x0::MODE_RX, {HIGH, LOW}},
-    {LR11x0::MODE_TX, {LOW, HIGH}},   {LR11x0::MODE_TX_HP, {LOW, HIGH}},
-    {LR11x0::MODE_TX_HF, {LOW, LOW}}, {LR11x0::MODE_GNSS, {LOW, LOW}},
-    {LR11x0::MODE_WIFI, {LOW, LOW}},  END_OF_MODE_TABLE,
-};
@@ -1,83 +0,0 @@
-#define HAS_SDCARD
-#define SDCARD_USE_SPI1
-
-#define HAS_GPS 1
-#define GPS_RX_PIN 39
-#define GPS_TX_PIN 42
-#define GPS_BAUDRATE_FIXED 1
-#define GPS_BAUDRATE 9600
-
-#define I2C_SDA 17 // I2C pins for this board
-#define I2C_SCL 18
-
-#define HAS_SCREEN 1 // Allow for OLED Screens on I2C Header of shield
-
-#define LED_PIN 38   // If defined we will blink this LED
-#define BUTTON_PIN 0 // If defined, this will be used for user button presses,
-
-#define BUTTON_NEED_PULLUP
-
-// TTGO uses a common pinout for their SX1262 vs RF95 modules - both can be enabled and we will probe at runtime for RF95 and if
-// not found then probe for SX1262
-#define USE_RF95 // RFM95/SX127x
-#define USE_SX1262
-#define USE_SX1280
-#define USE_LR1121
-
-#define LORA_SCK 10
-#define LORA_MISO 9
-#define LORA_MOSI 11
-#define LORA_CS 40
-#define LORA_RESET 46
-
-// per SX1276_Receive_Interrupt/utilities.h
-#define LORA_DIO0 8
-#define LORA_DIO1 16
-#define LORA_DIO2 RADIOLIB_NC
-
-// per SX1262_Receive_Interrupt/utilities.h
-#ifdef USE_SX1262
-#define SX126X_CS LORA_CS
-#define SX126X_DIO1 8
-#define SX126X_BUSY 16
-#define SX126X_RESET LORA_RESET
-#define SX126X_DIO2_AS_RF_SWITCH
-#define SX126X_DIO3_TCXO_VOLTAGE 1.8
-#endif
-
-// per SX128x_Receive_Interrupt/utilities.h
-#ifdef USE_SX1280
-#define SX128X_CS LORA_CS
-#define SX128X_DIO1 8
-#define SX128X_DIO2 33
-#define SX128X_DIO3 34
-#define SX128X_BUSY 16
-#define SX128X_RESET LORA_RESET
-#define SX128X_RXEN 13
-#define SX128X_TXEN 38
-#define SX128X_MAX_POWER 3
-#endif
-
-// LR1121
-#ifdef USE_LR1121
-#define LR1121_IRQ_PIN 8
-#define LR1121_NRESET_PIN LORA_RESET
-#define LR1121_BUSY_PIN 16
-#define LR1121_SPI_NSS_PIN LORA_CS
-#define LR1121_SPI_SCK_PIN LORA_SCK
-#define LR1121_SPI_MOSI_PIN LORA_MOSI
-#define LR1121_SPI_MISO_PIN LORA_MISO
-#define LR11X0_DIO3_TCXO_VOLTAGE 3.0
-#define LR11X0_DIO_AS_RF_SWITCH
-#endif
-
-#define HAS_ETHERNET 1
-#define USE_WS5500 1 // this driver uses the same stack as the ESP32 Wifi driver
-
-#define ETH_MISO_PIN 47
-#define ETH_MOSI_PIN 21
-#define ETH_SCLK_PIN 48
-#define ETH_CS_PIN 45
-#define ETH_INT_PIN 14
-#define ETH_RST_PIN -1
-#define ETH_ADDR 1