#define VEXT_ENABLE 40 // active low, powers the oled display and the lora antenna boost
#define VEXT_ON_VALUE LOW
#define BUTTON_PIN 0

#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC_CHANNEL_0
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER 4.9 * 1.035

#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3    // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TCXO is enabled

#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8

#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET

#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8

// Enable Traffic Management Module for Heltec V4
#ifndef HAS_TRAFFIC_MANAGEMENT
#define HAS_TRAFFIC_MANAGEMENT 1
#endif
#ifndef TRAFFIC_MANAGEMENT_CACHE_SIZE
#define TRAFFIC_MANAGEMENT_CACHE_SIZE 2048
#endif

// ---- KCT8103L RF FRONT END CONFIGURATION ----
// The Heltec V4.3 uses a KCT8103L FEM chip with integrated PA and LNA
// RF path: SX1262 -> Pi attenuator -> KCT8103L PA -> Antenna
// Control logic (from KCT8103L datasheet):
//   Transmit PA:     CSD=1, CTX=1, CPS=1
//   Receive LNA:     CSD=1, CTX=0, CPS=X  (21dB gain, 1.9dB NF)
//   Receive bypass:  CSD=1, CTX=1, CPS=0
//   Shutdown:        CSD=0, CTX=X, CPS=X
// Pin mapping:
//   CPS (pin 5)  -> SX1262 DIO2: TX/RX path select (automatic via SX126X_DIO2_AS_RF_SWITCH)
//   CSD (pin 4)  -> GPIO2: Chip enable (HIGH=on, LOW=shutdown)
//   CTX (pin 6)  -> GPIO5: Switch between Receive LNA Mode and Receive Bypass Mode. (HIGH=RX bypass, LOW=RX LNA)
//   VCC0/VCC1    -> Vfem via U3 LDO, controlled by GPIO7
// KCT8103L FEM: TX/RX path switching is handled by DIO2 -> CPS pin (via SX126X_DIO2_AS_RF_SWITCH)

#define USE_KCT8103L_PA
#define LORA_PA_POWER 7        // VFEM_Ctrl - KCT8103L LDO power enable
#define LORA_KCT8103L_PA_CSD 2 // CSD - KCT8103L chip enable (HIGH=on)
#define LORA_KCT8103L_PA_CTX 5 // CTX - Switch between Receive LNA Mode and Receive Bypass Mode. (HIGH=RX bypass, LOW=RX LNA)

#if HAS_TFT
#define USE_TFTDISPLAY 1
#endif
/*
 * GPS pins
 */
#define GPS_L76K
#define PIN_GPS_EN (42)
#define GPS_EN_ACTIVE LOW
#define PERIPHERAL_WARMUP_MS 1000 // Make sure I2C QuickLink has stable power before continuing
#define PIN_GPS_PPS (41)
// Seems to be missing on this new board
#define GPS_TX_PIN (38) // This is for bits going TOWARDS the CPU
#define GPS_RX_PIN (39) // This is for bits going TOWARDS the GPS
#define GPS_THREAD_INTERVAL 50