@@ -45,10 +45,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
// If we are using the JTAG port for debugging, some pins must be left free for that (and things like GPS have to be disabled)
// we don't support jtag on the ttgo - access to gpio 12 is a PITA
# ifdef ARDUINO_HELTEC_WIFI_LORA_32_V2
//#define USE_JTAG
# endif
# define REQUIRE_RADIO true // If true, we will fail to start if the radio is not found
/// Convert a preprocessor name into a quoted string
@@ -88,18 +84,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
# define BUTTON_PIN_TOUCH PIN_BUTTON_TOUCH
# endif
// FIXME, use variant.h defs for all of this!!! (even on the ESP32 targets)
# elif defined(CubeCell_BoardPlus)
//
// Standard definitions for CubeCell targets
//
# define NO_ESP32 // Don't use ESP32 libs (mainly bluetooth)
# define LED_PIN -1 // FIXME totally bogus
# define BUTTON_PIN -1
# else
//
@@ -169,338 +153,51 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_TBEAM
// #define BUTTON_NEED_PULLUP // if set we need to turn on the internal CPU pullup during sleep
# define I2C_SDA 21
# define I2C_SCL 22
# define BUTTON_PIN 38 // The middle button GPIO on the T-Beam
//#define BUTTON_PIN_ALT 13 // Alternate GPIO for an external button if needed. Does anyone use this? It is not documented anywhere.
# define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Plugin.
# define LED_INVERTED 1
# define LED_PIN 4 // Newer tbeams (1.1) have an extra led on GPIO4
// TTGO uses a common pinout for their SX1262 vs RF95 modules - both can be enabled and we will probe at runtime for RF95 and if
// not found then probe for SX1262
# define USE_RF95
# define USE_SX1262
# define LORA_DIO0 26 // a No connect on the SX1262 module
# define LORA_RESET 23
# define LORA_DIO1 33 // SX1262 IRQ
# define LORA_DIO2 32 // SX1262 BUSY
# define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
# ifdef USE_SX1262
# define SX126X_CS RF95_NSS // FIXME - we really should define LORA_CS instead
# define SX126X_DIO1 LORA_DIO1
# define SX126X_BUSY LORA_DIO2
# define SX126X_RESET LORA_RESET
# define SX126X_E22 // Not really an E22 but TTGO seems to be trying to clone that
// Internally the TTGO module hooks the SX1262-DIO2 in to control the TX/RX switch (which is the default for the sx1262interface
// code)
# endif
// Leave undefined to disable our PMU IRQ handler. DO NOT ENABLE THIS because the pmuirq can cause sperious interrupts
// and waking from light sleep
// #define PMU_IRQ 35
# define AXP192_SLAVE_ADDRESS 0x34
# elif defined(TBEAM_V07)
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_TBEAM0p7
// #define BUTTON_NEED_PULLUP // if set we need to turn on the internal CPU pullup during sleep
# define I2C_SDA 21
# define I2C_SCL 22
# define BUTTON_PIN 39
# define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
# define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Plugin.
# define USE_RF95
# define LORA_DIO0 26 // a No connect on the SX1262 module
# define LORA_RESET 23
# define LORA_DIO1 33 // Not really used
# define LORA_DIO2 32 // Not really used
// This board has different GPS pins than all other boards
# undef GPS_RX_PIN
# undef GPS_TX_PIN
# define GPS_RX_PIN 12
# define GPS_TX_PIN 15
# elif defined(DIY_V1)
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_DIY_V1
// For OLED LCD
# define I2C_SDA 21
# define I2C_SCL 22
// GPS
# undef GPS_RX_PIN
# define GPS_RX_PIN 15
//#undef GPS_TX_PIN
//#define GPS_TX_PIN 12 // not connected
# define BUTTON_PIN 39 // The middle button GPIO on the T-Beam
# define EXT_NOTIFY_OUT 12 // Overridden default pin to use for Ext Notify Plugin (#975).
# define LED_PIN 2 // add status LED (compatible with core-pcb and DIY targets)
# define LORA_DIO0 26 // a No connect on the SX1262/SX1268 module
# define LORA_RESET 23 // RST for SX1276, and for SX1262/SX1268
# define LORA_DIO1 33 // IRQ for SX1262/SX1268
# define LORA_DIO2 32 // BUSY for SX1262/SX1268
# define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262/SX1268, if DIO3 is high the TXCO is enabled
# define RF95_SCK 5
# define RF95_MISO 19
# define RF95_MOSI 27
# define RF95_NSS 18
// supported modules list
# define USE_SX1262
# define USE_SX1268
# define USE_LLCC68
// common pinouts for SX126X modules
# define SX126X_CS 18 // NSS for SX126X
# define SX126X_DIO1 LORA_DIO1
# define SX126X_BUSY LORA_DIO2
# define SX126X_RESET LORA_RESET
# define SX126X_RXEN 14
# define SX126X_TXEN 13
# ifdef EBYTE_E22
// Internally the TTGO module hooks the SX126x-DIO2 in to control the TX/RX switch
// (which is the default for the sx1262interface code)
# define SX126X_E22
# endif
# elif defined(ARDUINO_HELTEC_WIFI_LORA_32_V2)
// the default ESP32 Pin of 15 is the Oled SCL, set to 36 and 37 and works fine.
// Tested on Neo6m module.
# undef GPS_RX_PIN
# undef GPS_TX_PIN
# define GPS_RX_PIN 36
# define GPS_TX_PIN 37
# ifndef USE_JTAG // gpio15 is TDO for JTAG, so no I2C on this board while doing jtag
# define I2C_SDA 4 // I2C pins for this board
# define I2C_SCL 15
# endif
# define RESET_OLED 16 // If defined, this pin will be used to reset the display controller
# define VEXT_ENABLE 21 // active low, powers the oled display and the lora antenna boost
# define LED_PIN 25 // If defined we will blink this LED
# define BUTTON_PIN 0 // If defined, this will be used for user button presses
# define USE_RF95
# define LORA_DIO0 26 // a No connect on the SX1262 module
# ifndef USE_JTAG
# define LORA_RESET 14
# endif
# define LORA_DIO1 35 // Not really used
# define LORA_DIO2 34 // Not really used
// ratio of voltage divider = 3.20 (R1=100k, R2=220k)
# define ADC_MULTIPLIER 3.2
# ifdef HELTEC_V2_0
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_HELTEC_V2_0
# define BATTERY_PIN 13 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
# endif
# ifdef HELTEC_V2_1
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_HELTEC_V2_1
# define BATTERY_PIN 37 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
# define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Plugin.
# endif
# elif defined(ARDUINO_HELTEC_WIFI_LORA_32)
// the default ESP32 Pin of 15 is the Oled SCL, set to 36 and 37 and works fine.
// Tested on Neo6m module.
# undef GPS_RX_PIN
# undef GPS_TX_PIN
# define GPS_RX_PIN 36
# define GPS_TX_PIN 37
# ifndef USE_JTAG // gpio15 is TDO for JTAG, so no I2C on this board while doing jtag
# define I2C_SDA 4 // I2C pins for this board
# define I2C_SCL 15
# endif
# define RESET_OLED 16 // If defined, this pin will be used to reset the display controller
# define LED_PIN 25 // If defined we will blink this LED
# define BUTTON_PIN 0 // If defined, this will be used for user button presses
# define USE_RF95
# define LORA_DIO0 26 // a No connect on the SX1262 module
# ifndef USE_JTAG
# define LORA_RESET 14
# endif
# define LORA_DIO1 33 // Not really used
# define LORA_DIO2 32 // Not really used
// ratio of voltage divider = 3.20 (R1=100k, R2=220k)
# define ADC_MULTIPLIER 3.2
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_HELTEC_V1
# define BATTERY_PIN 13 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
# elif defined(TLORA_V1)
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_TLORA_V1
# undef GPS_RX_PIN
# undef GPS_TX_PIN
# define GPS_RX_PIN 36
# define GPS_TX_PIN 37
# define I2C_SDA 4 // I2C pins for this board
# define I2C_SCL 15
# define RESET_OLED 16 // If defined, this pin will be used to reset the display controller
// #define VEXT_ENABLE 21 // active low, powers the oled display and the lora antenna boost
# define LED_PIN 2 // If defined we will blink this LED
# define BUTTON_PIN 0 // If defined, this will be used for user button presses
# define BUTTON_NEED_PULLUP
# define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Plugin.
# define USE_RF95
# define LORA_DIO0 26 // a No connect on the SX1262 module
# define LORA_RESET 14
# define LORA_DIO1 35 // Not really used
# define LORA_DIO2 34 // Not really used
# elif defined(TLORA_V2)
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_TLORA_V2
# undef GPS_RX_PIN
# undef GPS_TX_PIN
# define GPS_RX_PIN 36
# define GPS_TX_PIN 13 // per @eugene
# define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
# define I2C_SDA 21 // I2C pins for this board
# define I2C_SCL 22
# define RESET_OLED 16 // If defined, this pin will be used to reset the display controller
# define VEXT_ENABLE 21 // active low, powers the oled display and the lora antenna boost
# define LED_PIN 25 // If defined we will blink this LED
# define BUTTON_PIN \
0 // If defined, this will be used for user button presses, if your board doesn't have a physical switch, you can wire one
// between this pin and ground
# define BUTTON_NEED_PULLUP
# define USE_RF95
# define LORA_DIO0 26 // a No connect on the SX1262 module
# define LORA_RESET 14
# define LORA_DIO1 35 // Not really used
# define LORA_DIO2 34 // Not really used
# elif defined(TLORA_V1_3)
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_TLORA_V1_1p3
# undef GPS_RX_PIN
# undef GPS_TX_PIN
# define GPS_RX_PIN 36
# define GPS_TX_PIN 13 // per @eugene
# define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
# define I2C_SDA 21 // I2C pins for this board
# define I2C_SCL 22
# define RESET_OLED 16 // If defined, this pin will be used to reset the display controller
# define VEXT_ENABLE 21 // active low, powers the oled display and the lora antenna boost
# define LED_PIN 25 // If defined we will blink this LED
# define BUTTON_PIN 36
# define BUTTON_NEED_PULLUP
# define USE_RF95
# define LORA_DIO0 26 // a No connect on the SX1262 module
# define LORA_RESET 14
# define LORA_DIO1 35 // Not really used
# define LORA_DIO2 34 // Not really used
# elif defined(TLORA_V2_1_16)
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_TLORA_V2_1_1p6
# undef GPS_RX_PIN
# undef GPS_TX_PIN
# define GPS_RX_PIN 15 // per @der_bear on the forum, 36 is incorrect for this board type and 15 is a better pick
# define GPS_TX_PIN 13
# define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
# define I2C_SDA 21 // I2C pins for this board
# define I2C_SCL 22
# define RESET_OLED 16 // If defined, this pin will be used to reset the display controller
# define VEXT_ENABLE 21 // active low, powers the oled display and the lora antenna boost
# define LED_PIN 25 // If defined we will blink this LED
# define BUTTON_PIN 12 // If defined, this will be used for user button presses,
# define BUTTON_NEED_PULLUP
# define USE_RF95
# define LORA_DIO0 26 // a No connect on the SX1262 module
# define LORA_RESET 14
# define LORA_DIO1 35 // Not really used
# define LORA_DIO2 34 // Not really used
# elif defined(GENIEBLOCKS)
// This string must exactly match the case used in release file names or the android updater won't work
# define HW_VENDOR HardwareModel_GENIEBLOCKS
# undef GPS_RX_PIN
# undef GPS_TX_PIN
# define GPS_RX_PIN 5
# define GPS_TX_PIN 18
# define GPS_RESET_N 10
# define GPS_EXTINT 23 // On MAX-M8 module pin name is EXTINT. On L70 module pin name is STANDBY.
# define BATTERY_PIN 39 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
# define BATTERY_EN_PIN 14 // Voltage voltage divider enable pin connected to mosfet
# define I2C_SDA 4 // I2C pins for this board
# define I2C_SCL 2
# define LED_PIN 12 // If defined we will blink this LED
//#define BUTTON_PIN 36 // If defined, this will be used for user button presses (ToDo problem on that line on debug screen -->
// Long press start!) #define BUTTON_NEED_PULLUP //GPIOs 34 to 39 are GPIs – ’
// pull-ups or pull-down resistors.
# define USE_RF95
# define LORA_DIO0 38 // a No connect on the SX1262 module
# define LORA_RESET 9
# define RF95_SCK 22
# define RF95_MISO 19
# define RF95_MOSI 13
# define RF95_NSS 21
# endif
@@ -533,100 +230,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
# define HW_VENDOR HardwareModel_PORTDUINO
# define USE_SIM_RADIO
// Pine64 uses a common pinout for their SX1262 vs RF95 modules - both can be enabled and we will probe at runtime for RF95 and if
// not found then probe for SX1262. Currently the RF95 code is disabled because I think the RF95 module won't need to ship.
// #define USE_RF95
# define USE_SX1262
// Fake SPI device selections
# define RF95_SCK 5
# define RF95_MISO 19
# define RF95_MOSI 27
# define RF95_NSS RADIOLIB_NC // the ch341f spi controller does CS for us
# define LORA_DIO0 26 // a No connect on the SX1262 module
# define LORA_RESET 14
# define LORA_DIO1 33 // SX1262 IRQ, called DIO0 on pinelora schematic, pin 7 on ch341f "ack" - FIXME, enable hwints in linux
# define LORA_DIO2 32 // SX1262 BUSY, actually connected to "DIO5" on pinelora schematic, pin 8 on ch341f "slct"
# define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
# ifdef USE_SX1262
# define SX126X_CS 20 // CS0 on pinelora schematic, hooked to gpio D0 on ch341f
# define SX126X_DIO1 LORA_DIO1
# define SX126X_BUSY LORA_DIO2
# define SX126X_RESET LORA_RESET
// HOPE RFM90 does not have a TCXO therefore not SX126X_E22
# endif
# endif
// DEBUG LED
# ifndef LED_INVERTED
# define LED_INVERTED 0 // define as 1 if LED is active low (on)
# endif
# ifdef USE_RF95
# define RF95_RESET LORA_RESET
# define RF95_IRQ LORA_DIO0 // on SX1262 version this is a no connect DIO0
# define RF95_DIO1 LORA_DIO1 // Note: not really used for RF95
# define RF95_DIO2 LORA_DIO2 // Note: not really used for RF95
# endif
// -----------------------------------------------------------------------------
// DEBUG
// -----------------------------------------------------------------------------
# ifdef CONSOLE_MAX_BAUD
# define SERIAL_BAUD CONSOLE_MAX_BAUD
# else
# define SERIAL_BAUD 921600 // Serial debug baud rate
# endif
# include "SerialConsole.h"
# define DEBUG_PORT (*console) // Serial debug port
// What platforms should use SEGGER?
# ifdef NRF52_SERIES
// Always include the SEGGER code on NRF52 - because useful for debugging
# include "SEGGER_RTT.h"
// The channel we send stdout data to
# define SEGGER_STDOUT_CH 0
// Debug printing to segger console
# define SEGGER_MSG(...) SEGGER_RTT_printf(SEGGER_STDOUT_CH, __VA_ARGS__)
// If we are not on a NRF52840 (which has built in USB-ACM serial support) and we don't have serial pins hooked up, then we MUST
// use SEGGER for debug output
# if !defined(PIN_SERIAL_RX) && !defined(NRF52840_XXAA)
// No serial ports on this board - ONLY use segger in memory console
# define USE_SEGGER
# endif
# else
# define SERIAL0_RX_GPIO 3 // Always GPIO3 on ESP32
# endif
# ifdef USE_SEGGER
# define DEBUG_MSG(...) SEGGER_RTT_printf(0, __VA_ARGS__)
# else
# ifdef DEBUG_PORT
# define DEBUG_MSG(...) DEBUG_PORT.logDebug(__VA_ARGS__)
# else
# define DEBUG_MSG(...)
# endif
# endif
// -----------------------------------------------------------------------------
// AXP192 (Rev1-specific options)
// -----------------------------------------------------------------------------
# define GPS_POWER_CTRL_CH 3
# define LORA_POWER_CTRL_CH 2
// Default Bluetooth PIN
# define defaultBLEPin 123456
# include "variant.h"
# include "RF95Configuration.h"
# include "DebugConfiguration.h"
Balázs Kelemen
GitHub