diff --git a/src/main.cpp b/src/main.cpp
index e517f94f0..cee18bb75 100644
--- a/src/main.cpp
+++ b/src/main.cpp
@@ -347,69 +347,6 @@ void setup()
 #endif
 #endif
 
-#if defined(T_DECK)
-    // GPIO10 manages all peripheral power supplies
-    // Turn on peripheral power immediately after MUC starts.
-    // If some boards are turned on late, ESP32 will reset due to low voltage.
-    // ESP32-C3(Keyboard) , MAX98357A(Audio Power Amplifier) ,
-    // TF Card , Display backlight(AW9364DNR) , AN48841B(Trackball) , ES7210(Decoder)
-    pinMode(KB_POWERON, OUTPUT);
-    digitalWrite(KB_POWERON, HIGH);
-    // T-Deck has all three SPI peripherals (TFT, SD, LoRa) attached to the same SPI bus
-    // We need to initialize all CS pins in advance otherwise there will be SPI communication issues
-    // e.g. when detecting the SD card
-    pinMode(LORA_CS, OUTPUT);
-    digitalWrite(LORA_CS, HIGH);
-    pinMode(SDCARD_CS, OUTPUT);
-    digitalWrite(SDCARD_CS, HIGH);
-    pinMode(TFT_CS, OUTPUT);
-    digitalWrite(TFT_CS, HIGH);
-    delay(100);
-#elif defined(T_DECK_PRO)
-    pinMode(LORA_EN, OUTPUT);
-    digitalWrite(LORA_EN, HIGH);
-    pinMode(LORA_CS, OUTPUT);
-    digitalWrite(LORA_CS, HIGH);
-    pinMode(SDCARD_CS, OUTPUT);
-    digitalWrite(SDCARD_CS, HIGH);
-    pinMode(PIN_EINK_CS, OUTPUT);
-    digitalWrite(PIN_EINK_CS, HIGH);
-#if PIN_EINK_RES >= 0
-    pinMode(PIN_EINK_RES, OUTPUT);
-    digitalWrite(PIN_EINK_RES, HIGH);
-#endif
-    pinMode(CST328_PIN_RST, OUTPUT);
-    digitalWrite(CST328_PIN_RST, HIGH);
-#elif defined(T_LORA_PAGER)
-    pinMode(LORA_CS, OUTPUT);
-    digitalWrite(LORA_CS, HIGH);
-    pinMode(SDCARD_CS, OUTPUT);
-    digitalWrite(SDCARD_CS, HIGH);
-    pinMode(TFT_CS, OUTPUT);
-    digitalWrite(TFT_CS, HIGH);
-    pinMode(KB_INT, INPUT_PULLUP);
-    // io expander
-    io.begin(Wire, XL9555_SLAVE_ADDRESS0, SDA, SCL);
-    io.pinMode(EXPANDS_DRV_EN, OUTPUT);
-    io.digitalWrite(EXPANDS_DRV_EN, HIGH);
-    io.pinMode(EXPANDS_AMP_EN, OUTPUT);
-    io.digitalWrite(EXPANDS_AMP_EN, LOW);
-    io.pinMode(EXPANDS_LORA_EN, OUTPUT);
-    io.digitalWrite(EXPANDS_LORA_EN, HIGH);
-    io.pinMode(EXPANDS_GPS_EN, OUTPUT);
-    io.digitalWrite(EXPANDS_GPS_EN, HIGH);
-    io.pinMode(EXPANDS_KB_EN, OUTPUT);
-    io.digitalWrite(EXPANDS_KB_EN, HIGH);
-    io.pinMode(EXPANDS_SD_EN, OUTPUT);
-    io.digitalWrite(EXPANDS_SD_EN, HIGH);
-    io.pinMode(EXPANDS_GPIO_EN, OUTPUT);
-    io.digitalWrite(EXPANDS_GPIO_EN, HIGH);
-    io.pinMode(EXPANDS_SD_PULLEN, INPUT);
-#elif defined(HACKADAY_COMMUNICATOR)
-    pinMode(KB_INT, INPUT);
-    digitalWrite(BLE_LED, LED_STATE_OFF);
-#endif
-
 #if defined(T_DECK)
     // GPIO10 manages all peripheral power supplies
     // Turn on peripheral power immediately after MUC starts.