Merge pull request #7773 from meshtastic/master

Backmerge
2025-08-27 20:53:55 -05:00
parent 67e3a17b28 834c3c5cc2
commit 8685436cbb
52 changed files with 1545 additions and 146 deletions
@@ -19,8 +19,6 @@ build_flags = ${esp32s3_base.build_flags} -Os
  -D MESHTASTIC_EXCLUDE_SERIAL=1
  -D MESHTASTIC_EXCLUDE_SOCKETAPI=1
  -D MESHTASTIC_EXCLUDE_SCREEN=1
-  -D MESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
-  -D HAS_TELEMETRY=0
  -D CONFIG_DISABLE_HAL_LOCKS=1
  -D USE_PIN_BUZZER
  -D HAS_SCREEN=0
@@ -0,0 +1,19 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// used for keyboard, battery gauge, charger and haptic driver
+static const uint8_t SDA = 3;
+static const uint8_t SCL = 2;
+
+// Default SPI will be mapped to Radio
+static const uint8_t SS = 36;
+static const uint8_t MOSI = 34;
+static const uint8_t MISO = 33;
+static const uint8_t SCK = 35;
+
+#endif /* Pins_Arduino_h */
@@ -0,0 +1,71 @@
+; LilyGo T-Lora-Pager
+[env:tlora-pager]
+extends = esp32s3_base
+board = t-deck-pro ; same as T-Deck Pro
+board_check = true
+board_build.partitions = default_16MB.csv
+upload_protocol = esptool
+
+build_flags = ${esp32s3_base.build_flags} 
+  -I variants/esp32s3/tlora-pager
+  -D T_LORA_PAGER 
+  -D BOARD_HAS_PSRAM
+  -D GPS_POWER_TOGGLE
+  -D HAS_SDCARD
+  -D SDCARD_USE_SPI1
+  -D ENABLE_ROTARY_PULLUP
+  -D ENABLE_BUTTON_PULLUP
+  -D HALF_STEP
+
+lib_deps = ${esp32s3_base.lib_deps}
+  lovyan03/LovyanGFX@1.2.7
+  earlephilhower/ESP8266Audio@1.9.9
+  earlephilhower/ESP8266SAM@1.0.1
+  adafruit/Adafruit DRV2605 Library@1.2.4
+  lewisxhe/PCF8563_Library@1.0.1
+  lewisxhe/SensorLib@0.3.1
+  https://github.com/pschatzmann/arduino-audio-driver/archive/refs/tags/v0.1.3.zip
+  https://github.com/mverch67/BQ27220/archive/07d92be846abd8a0258a50c23198dac0858b22ed.zip
+  https://github.com/mverch67/RotaryEncoder
+
+[env:tlora-pager-tft]
+board_level = extra
+extends = env:tlora-pager
+build_flags =
+  ${env:tlora-pager.build_flags}
+  -D CONFIG_DISABLE_HAL_LOCKS=1
+  -D INPUTDRIVER_ROTARY_TYPE=1
+  -D INPUTDRIVER_ROTARY_UP=40
+  -D INPUTDRIVER_ROTARY_DOWN=41
+  -D INPUTDRIVER_ROTARY_BTN=7
+  -D INPUTDRIVER_BUTTON_TYPE=0
+  -D HAS_SCREEN=1
+  -D HAS_TFT=1
+  -D USE_I2S_BUZZER
+  -D RAM_SIZE=5120
+  -D LV_LVGL_H_INCLUDE_SIMPLE
+  -D LV_CONF_INCLUDE_SIMPLE
+  -D LV_COMP_CONF_INCLUDE_SIMPLE
+  -D LV_USE_SYSMON=0
+  -D LV_USE_PROFILER=0
+  -D LV_USE_PERF_MONITOR=0
+  -D LV_USE_MEM_MONITOR=0
+  -D LV_USE_LOG=0
+  -D USE_LOG_DEBUG
+  -D LOG_DEBUG_INC=\"DebugConfiguration.h\"
+  -D RADIOLIB_SPI_PARANOID=0
+  -D LGFX_SCREEN_WIDTH=222
+  -D LGFX_SCREEN_HEIGHT=480
+  -D DISPLAY_SIZE=480x222 ; landscape mode
+  -D DISPLAY_SET_RESOLUTION
+  -D LGFX_DRIVER=LGFX_TLORA_PAGER
+  -D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_T_LORA_PAGER.h\"
+;  -D LVGL_DRIVER=LVGL_T_LORA_PAGER
+;  -D LV_USE_ST7796=1
+  -D VIEW_480x222
+  -D USE_PACKET_API
+  -D MAP_FULL_REDRAW
+
+lib_deps =
+  ${env:tlora-pager.lib_deps}
+  ${device-ui_base.lib_deps}
@@ -0,0 +1,125 @@
+// ST7796 TFT LCD
+#define TFT_CS 38
+#define ST7796_CS TFT_CS
+#define ST7796_RS 37    // DC
+#define ST7796_SDA MOSI // MOSI
+#define ST7796_SCK SCK
+#define ST7796_RESET -1
+#define ST7796_MISO MISO
+#define ST7796_BUSY -1
+#define ST7796_BL 42
+#define ST7796_SPI_HOST SPI2_HOST
+#define TFT_BL 42
+#define SPI_FREQUENCY 75000000
+#define SPI_READ_FREQUENCY 16000000
+#define TFT_HEIGHT 480
+#define TFT_WIDTH 222
+#define TFT_OFFSET_X 49
+#define TFT_OFFSET_Y 0
+#define TFT_OFFSET_ROTATION 3
+#define SCREEN_ROTATE
+#define SCREEN_TRANSITION_FRAMERATE 5
+#define BRIGHTNESS_DEFAULT 130 // Medium Low Brightness
+
+#define I2C_SDA SDA
+#define I2C_SCL SCL
+
+#define USE_POWERSAVE
+#define SLEEP_TIME 120
+
+// GNNS
+#define HAS_GPS 1
+#define GPS_BAUDRATE 38400
+#define GPS_RX_PIN 4
+#define GPS_TX_PIN 12
+#define PIN_GPS_PPS 13
+
+// PCF8563 RTC Module
+#if __has_include("pcf8563.h")
+#include "pcf8563.h"
+#endif
+#define PCF8563_RTC 0x51
+#define HAS_RTC 1
+
+// Rotary
+#define ROTARY_A (40)
+#define ROTARY_B (41)
+#define ROTARY_PRESS (7)
+
+#define BUTTON_PIN 0
+
+// SPI interface SD card slot
+#define SPI_MOSI MOSI
+#define SPI_SCK SCK
+#define SPI_MISO MISO
+#define SPI_CS 21
+#define SDCARD_CS SPI_CS
+#define SD_SPI_FREQUENCY 75000000U
+
+// TCA8418 keyboard
+#define I2C_NO_RESCAN
+#define KB_BL_PIN 46
+#define KB_INT 6
+#define CANNED_MESSAGE_MODULE_ENABLE 1
+
+// audio codec ES8311
+#define HAS_I2S
+#define DAC_I2S_BCK 11
+#define DAC_I2S_WS 18
+#define DAC_I2S_DOUT 45
+#define DAC_I2S_DIN 17
+#define DAC_I2S_MCLK 10
+
+// gyroscope BHI260AP
+#define HAS_BHI260AP
+
+// battery charger BQ25896
+#define HAS_PPM 1
+#define XPOWERS_CHIP_BQ25896
+
+// battery quality management BQ27220
+#define HAS_BQ27220 1
+#define BQ27220_I2C_SDA SDA
+#define BQ27220_I2C_SCL SCL
+#define BQ27220_DESIGN_CAPACITY 1500
+
+// NFC ST25R3916
+#define NFC_INT 5
+#define NFC_CS 39
+
+// External expansion chip XL9555
+#define USE_XL9555
+#define EXPANDS_DRV_EN (0)
+#define EXPANDS_AMP_EN (1)
+#define EXPANDS_KB_RST (2)
+#define EXPANDS_LORA_EN (3)
+#define EXPANDS_GPS_EN (4)
+#define EXPANDS_NFC_EN (5)
+#define EXPANDS_GPS_RST (7)
+#define EXPANDS_KB_EN (8)
+#define EXPANDS_GPIO_EN (9)
+#define EXPANDS_SD_DET (10)
+#define EXPANDS_SD_PULLEN (11)
+#define EXPANDS_SD_EN (12)
+
+// LoRa
+#define USE_SX1262
+#define USE_SX1268
+
+#define LORA_SCK 35
+#define LORA_MISO 33
+#define LORA_MOSI 34
+#define LORA_CS 36
+
+#define LORA_DIO0 -1 // a No connect on the SX1262 module
+#define LORA_RESET 47
+#define LORA_DIO1 14 // SX1262 IRQ
+#define LORA_DIO2 48 // SX1262 BUSY
+#define LORA_DIO3    // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
+
+#define SX126X_CS LORA_CS
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY LORA_DIO2
+#define SX126X_RESET LORA_RESET
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 3.0
@@ -32,6 +32,7 @@ lib_deps = ${esp32s3_base.lib_deps}


 [env:unphone-tft]
+board_level = extra
 extends = env:unphone
 build_flags =
  ${env:unphone.build_flags}
@@ -52,8 +53,6 @@ build_flags =
  -D LV_USE_PERF_MONITOR=0
  -D LV_USE_MEM_MONITOR=0
  -D LV_USE_LOG=0
-  -D USE_LOG_DEBUG
-  -D LOG_DEBUG_INC=\"DebugConfiguration.h\"
  -D LGFX_SCREEN_WIDTH=320
  -D LGFX_SCREEN_HEIGHT=480
  -D DISPLAY_SIZE=320x480 ; portrait mode
@@ -0,0 +1,19 @@
+; First prototype nrf52840/sx1262 device
+[env:heltec-mesh-solar]
+extends = nrf52840_base
+board = heltec_mesh_solar
+board_level = pr
+debug_tool = jlink
+
+# add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
+build_flags = ${nrf52840_base.build_flags}
+  -Ivariants/nrf52840/heltec_mesh_solar
+  -DGPS_POWER_TOGGLE
+  -DHELTEC_MESH_SOLAR
+
+build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/heltec_mesh_solar>
+lib_deps = 
+  ${nrf52840_base.lib_deps}
+  https://github.com/NMIoT/meshsolar/archive/dfc5330dad443982e6cdd37a61d33fc7252f468b.zip
+  lewisxhe/PCF8563_Library@^1.0.1
+  ArduinoJson@6.21.4
@@ -0,0 +1,36 @@
+/*
+  Copyright (c) 2014-2015 Arduino LLC.  All right reserved.
+  Copyright (c) 2016 Sandeep Mistry All right reserved.
+  Copyright (c) 2018, Adafruit Industries (adafruit.com)
+
+  This library is free software; you can redistribute it and/or
+  modify it under the terms of the GNU Lesser General Public
+  License as published by the Free Software Foundation; either
+  version 2.1 of the License, or (at your option) any later version.
+
+  This library is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+  See the GNU Lesser General Public License for more details.
+
+  You should have received a copy of the GNU Lesser General Public
+  License along with this library; if not, write to the Free Software
+  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#include "variant.h"
+#include "nrf.h"
+#include "wiring_constants.h"
+#include "wiring_digital.h"
+
+const uint32_t g_ADigitalPinMap[] = {
+    // P0 - pins 0 and 1 are hardwired for xtal and should never be enabled
+    0xff, 0xff, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
+
+    // P1
+    32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
+
+void initVariant()
+{
+  pinMode(BQ4050_EMERGENCY_SHUTDOWN_PIN, INPUT);
+}
@@ -0,0 +1,157 @@
+/*
+ Copyright (c) 2014-2015 Arduino LLC.  All right reserved.
+ Copyright (c) 2016 Sandeep Mistry All right reserved.
+ Copyright (c) 2018, Adafruit Industries (adafruit.com)
+
+ This library is free software; you can redistribute it and/or
+ modify it under the terms of the GNU Lesser General Public
+ License as published by the Free Software Foundation; either
+ version 2.1 of the License, or (at your option) any later version.
+ This library is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ See the GNU Lesser General Public License for more details.
+ You should have received a copy of the GNU Lesser General Public
+ License along with this library; if not, write to the Free Software
+ Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+*/
+
+#ifndef _VARIANT_HELTEC_NRF_
+#define _VARIANT_HELTEC_NRF_
+/** Master clock frequency */
+#define VARIANT_MCK (64000000ul)
+
+#define USE_LFXO // Board uses 32khz crystal for LF
+
+/*----------------------------------------------------------------------------
+ *        Headers
+ *----------------------------------------------------------------------------*/
+
+#include "WVariant.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif // __cplusplus
+
+// Number of pins defined in PinDescription array
+#define PINS_COUNT (48)
+#define NUM_DIGITAL_PINS (48)
+#define NUM_ANALOG_INPUTS (1)
+#define NUM_ANALOG_OUTPUTS (0)
+
+
+#define PIN_LED1 (0 + 12) // green (confirmed on 1.0 board)
+#define LED_BLUE PIN_LED1 // fake for bluefruit library
+#define LED_GREEN PIN_LED1
+#define LED_BUILTIN LED_GREEN
+#define LED_STATE_ON 0  // State when LED is lit
+
+#define HAS_NEOPIXEL                         // Enable the use of neopixels
+#define NEOPIXEL_COUNT 1                     // How many neopixels are connected
+#define NEOPIXEL_DATA (32+15)                // gpio pin used to send data to the neopixels
+#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // type of neopixels in use
+
+/*
+ * Buttons
+ */
+#define PIN_BUTTON1 (32 + 10)
+// #define PIN_BUTTON2 (0 + 18)      // 0.18 is labeled on the board as RESET but we configure it in the bootloader as a regular
+// GPIO
+
+/*
+No longer populated on PCB
+*/
+#define PIN_SERIAL2_RX (0 + 9)
+#define PIN_SERIAL2_TX (0 + 10)
+//  #define PIN_SERIAL2_EN (0 + 17)
+
+/*
+ * I2C
+ */
+
+#define WIRE_INTERFACES_COUNT 2
+
+// I2C bus 0
+// Routed to footprint for PCF8563TS RTC
+// Not populated on T114 V1, maybe in future?
+#define PIN_WIRE_SDA (0 + 6) // P0.26
+#define PIN_WIRE_SCL (0 + 26) // P0.26
+
+// I2C bus 1
+// Available on header pins, for general use
+#define PIN_WIRE1_SDA (0 + 30) // P0.30
+#define PIN_WIRE1_SCL (0 + 5) // P0.13
+
+/*
+ * Lora radio
+ */
+
+#define USE_SX1262
+// #define USE_SX1268
+#define SX126X_CS (0 + 24) // FIXME - we really should define LORA_CS instead
+#define LORA_CS  (0 + 24)
+#define SX126X_DIO1 (0 + 20)
+// Note DIO2 is attached internally to the module to an analog switch for TX/RX switching
+// #define SX1262_DIO3 (0 + 21)
+// This is used as an *output* from the sx1262 and connected internally to power the tcxo, do not drive from the
+//    main
+// CPU?
+#define SX126X_BUSY  (0 + 17)
+#define SX126X_RESET (0 + 25)
+// Not really an E22 but TTGO seems to be trying to clone that
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+
+/*
+ * GPS pins
+ */
+
+#define GPS_L76K
+
+// #define PIN_GPS_RESET (32 + 6) // An output to reset L76K GPS. As per datasheet, low for > 100ms will reset the L76K
+// #define GPS_RESET_MODE LOW
+// #define PIN_GPS_EN (21)
+#define PERIPHERAL_WARMUP_MS 1000 // Make sure I2C QuickLink has stable power before continuing
+#define VEXT_ON_VALUE HIGH
+// #define GPS_EN_ACTIVE HIGH
+#define PIN_GPS_STANDBY (32 + 2) // An output to wake GPS, low means allow sleep, high means force wake
+#define PIN_GPS_PPS (32 + 4)
+// Seems to be missing on this new board
+// #define PIN_GPS_PPS (32 + 4)  // Pulse per second input from the GPS
+#define GPS_TX_PIN (32 + 5) // This is for bits going TOWARDS the CPU
+#define GPS_RX_PIN (32 + 7) // This is for bits going TOWARDS the GPS
+
+#define GPS_THREAD_INTERVAL 50
+
+#define PIN_SERIAL1_RX GPS_TX_PIN
+#define PIN_SERIAL1_TX GPS_RX_PIN
+
+/*
+ * SPI Interfaces
+ */
+#define SPI_INTERFACES_COUNT 1
+
+// For LORA, spi 0
+#define PIN_SPI_MISO (0 + 23)
+#define PIN_SPI_MOSI (0 + 22)
+#define PIN_SPI_SCK  (0 + 19)
+
+// #define PIN_PWR_EN (0 + 6)
+
+// To debug via the segger JLINK console rather than the CDC-ACM serial device
+// #define USE_SEGGER
+
+#define BQ4050_SDA_PIN                      (32+1) // I2C data line pin
+#define BQ4050_SCL_PIN                      (32+0) // I2C clock line pin
+#define BQ4050_EMERGENCY_SHUTDOWN_PIN       (32+3) // Emergency shutdown pin
+
+#define HAS_RTC 0
+#ifdef __cplusplus
+}
+#endif
+
+/*----------------------------------------------------------------------------
+ *        Arduino objects - C++ only
+ *----------------------------------------------------------------------------*/
+
+#endif
@@ -18,16 +18,9 @@

 // Shared NicheGraphics components
 // --------------------------------
-#include "graphics/niche/Drivers/Backlight/LatchingBacklight.h"
-#include "graphics/niche/Drivers/EInk/GDEY0213B74.h"
+#include "graphics/niche/Drivers/EInk/ZJY122250_0213BAAMFGN.h"
 #include "graphics/niche/Inputs/TwoButton.h"

-// Special case - fix T-Echo's touch button
-// ----------------------------------------
-// On a handful of T-Echos, LoRa TX triggers the capacitive touch
-// To avoid this, we lockout the button during TX
-#include "mesh/RadioLibInterface.h"
-
 void setupNicheGraphics()
 {
    using namespace NicheGraphics;
@@ -41,7 +34,7 @@ void setupNicheGraphics()
    // E-Ink Driver
    // -----------------------------

-    Drivers::EInk *driver = new Drivers::GDEY0213B74;
+    Drivers::EInk *driver = new Drivers::ZJY122250_0213BAAMFGN;
    driver->begin(&SPI1, PIN_EINK_DC, PIN_EINK_CS, PIN_EINK_BUSY, PIN_EINK_RES);

    // InkHUD
@@ -53,8 +46,7 @@ void setupNicheGraphics()
    inkhud->setDriver(driver);

    // Set how many FAST updates per FULL update
-    // Set how unhealthy additional FAST updates beyond this number are
-    inkhud->setDisplayResilience(7, 1.5);
+    inkhud->setDisplayResilience(15);

    // Select fonts
    InkHUD::Applet::fontLarge = FREESANS_12PT_WIN1252;
@@ -62,16 +54,10 @@ void setupNicheGraphics()
    InkHUD::Applet::fontSmall = FREESANS_6PT_WIN1252;

    // Customize default settings
-    inkhud->persistence->settings.userTiles.maxCount = 2;              // Two applets side-by-side
-                                                                       // 270 degrees clockwise
+    inkhud->persistence->settings.rotation = 1;                        // 90 degrees clockwise
    inkhud->persistence->settings.optionalFeatures.batteryIcon = true; // Device definitely has a battery
-    inkhud->persistence->settings.optionalMenuItems.backlight = true;  // Until proves capacitive button works by touching it
-    inkhud->persistence->settings.userTiles.count = 1; // One tile only by default, keep things simple for new users
-
-    // Setup backlight controller
-    // Note: AUX button attached further down
-    Drivers::LatchingBacklight *backlight = Drivers::LatchingBacklight::getInstance();
-    backlight->setPin(PIN_EINK_EN);
+    inkhud->persistence->settings.userTiles.count = 1;    // One tile only by default, keep things simple for new users
+    inkhud->persistence->settings.userTiles.maxCount = 2; // Two applets side-by-side

    // Pick applets
    // Note: order of applets determines priority of "auto-show" feature
@@ -83,11 +69,9 @@ void setupNicheGraphics()
    inkhud->addApplet("Recents List", new InkHUD::RecentsListApplet);            // -
    inkhud->addApplet("Heard", new InkHUD::HeardApplet, true, false, 0);         // Activated, no autoshow, default on tile 0

-    inkhud->persistence->settings.rotation = 1;
-    // inkhud->persistence->printSettings(&inkhud->persistence->settings);
    //  Start running InkHUD
    inkhud->begin();
-    // inkhud->persistence->printSettings(&inkhud->persistence->settings);
+
    //  Buttons
    //  --------------------------

@@ -1,17 +1,47 @@
 [env:seeed_wio_tracker_L1_eink]
 board = seeed_wio_tracker_L1
-extends = nrf52840_base, inkhud
+extends = nrf52840_base
 ;board_level = extra
 build_flags = ${nrf52840_base.build_flags}
-  ${inkhud.build_flags}
  -I variants/nrf52840/seeed_wio_tracker_L1_eink
  -D SEEED_WIO_TRACKER_L1_EINK
  -D SEEED_WIO_TRACKER_L1
  -I src/platform/nrf52/softdevice
  -I src/platform/nrf52/softdevice/nrf52
+  -DUSE_EINK
+  -DEINK_DISPLAY_MODEL=GxEPD2_213_B74
+  -DEINK_WIDTH=250
+  -DEINK_HEIGHT=122
+  -DUSE_EINK_DYNAMICDISPLAY            ; Enable Dynamic EInk
+  -DEINK_LIMIT_FASTREFRESH=10          ; How many consecutive fast-refreshes are permitted
+  -DEINK_LIMIT_RATE_BACKGROUND_SEC=30  ; Minimum interval between BACKGROUND updates
+  -DEINK_LIMIT_RATE_RESPONSIVE_SEC=1   ; Minimum interval between RESPONSIVE updates
+;   -D EINK_LIMIT_GHOSTING_PX=2000      ; (Optional) How much image ghosting is tolerated
+  -DEINK_BACKGROUND_USES_FAST          ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
+  -DEINK_HASQUIRK_GHOSTING             ; Display model is identified as "prone to ghosting"
+  -DEINK_HASQUIRK_WEAKFASTREFRESH      ; Pixels set with fast-refresh are easy to clear, disrupted by sunlight
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
-build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/seeed_wio_tracker_L1_eink> ${inkhud.build_src_filter}
+build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/seeed_wio_tracker_L1_eink>
 lib_deps =
-  ${inkhud.lib_deps}
  ${nrf52840_base.lib_deps}
+  https://github.com/meshtastic/GxEPD2#b202ebfec6a4821e098cf7a625ba0f6f2400292d
 debug_tool = jlink
+
+[env:seeed_wio_tracker_L1_eink-inkhud]
+board = seeed_wio_tracker_L1
+extends = nrf52840_base, inkhud
+build_flags = 
+  ${nrf52840_base.build_flags}
+  ${inkhud.build_flags}
+  -I variants/nrf52840/seeed_wio_tracker_L1_eink
+  -D SEEED_WIO_TRACKER_L1
+  -D BUTTON_PIN=D13
+board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
+build_src_filter = 
+  ${nrf52_base.build_src_filter}
+  ${inkhud.build_src_filter}
+  +<../variants/nrf52840/seeed_wio_tracker_L1_eink>
+lib_deps =
+  ${inkhud.lib_deps} ; Before base libs_deps, so we use ZinggJM/GFXRoot instead of AdafruitGFX (saves space)
+  ${nrf52840_base.lib_deps}
+debug_tool = jlink
@@ -33,17 +33,10 @@
 // ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
 //  Button Configuration
 // ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
-
-#ifdef BUTTON_PIN
-#undef BUTTON_PIN
-#endif
-
-#define BUTTON_PIN D13 // This is the Program Button
+#define CANCEL_BUTTON_PIN D13 // This is the Program Button
 // #define BUTTON_NEED_PULLUP   1
-#define BUTTON_ACTIVE_LOW true
-#define BUTTON_ACTIVE_PULLUP false
-
-#define BUTTON_PIN_TOUCH 13 // Touch button
+#define CANCEL_BUTTON_ACTIVE_LOW true
+#define CANCEL_BUTTON_ACTIVE_PULLUP false
 // ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
 //  Digital Pin Mapping (D0-D10)
 // ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
@@ -116,7 +109,7 @@ static const uint8_t SCL = PIN_WIRE_SCL;
 #define PIN_EINK_SCLK 31
 #define PIN_EINK_MOSI 33
 #define PIN_EINK_EN 14   // unused
-#define PIN_SPI1_MISO 15 // unused
+#define PIN_SPI1_MISO -1 // 15 unused
 #define PIN_SPI1_MOSI PIN_EINK_MOSI
 #define PIN_SPI1_SCK PIN_EINK_SCLK

@@ -175,7 +168,17 @@ static const uint8_t SCL = PIN_WIRE_SCL;
 //  joystick
 // ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

+// trackball
+#define HAS_TRACKBALL 1
+#define TB_UP 25
+#define TB_DOWN 26
+#define TB_LEFT 27
+#define TB_RIGHT 28
+#define TB_PRESS 29
+#define TB_DIRECTION FALLING
+
 #define CANNED_MESSAGE_MODULE_ENABLE 1
+#define CANNED_MESSAGE_ADD_CONFIRMATION 1

 // ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
 //  Compatibility Definitions