Merge branch 'develop' into clear-rangetest-results

2025-09-09 12:05:00 +12:00
parent c62f262f63 569a911455
commit 87a1449f76
119 changed files with 2197 additions and 909 deletions
@@ -0,0 +1,12 @@
+; 9M2IBR APRS LoRa Tracker: ESP32-WROOM-32 + EBYTE E22-400M30S
+; https://shopee.com.my/product/1095224/21692283917
+[env:9m2ibr_aprs_lora_tracker]
+extends = esp32_base
+board = esp32doit-devkit-v1
+board_level = extra
+build_flags =
+  ${esp32_base.build_flags}
+  -D PRIVATE_HW
+  -D EBYTE_E22
+  -D EBYTE_E22_900M30S ; Assume Tx power curve is identical to 900M30S as there is no documentation
+  -I variants/esp32/diy/9m2ibr_aprs_lora_tracker
@@ -0,0 +1,74 @@
+/*
+
+  9M2IBR APRS LoRa Tracker: ESP32-WROOM-32 + EBYTE E22-400M30S
+  https://shopee.com.my/product/1095224/21692283917
+
+  Originally developed for LoRa_APRS_iGate and GPIO is similar to
+  https://github.com/richonguzman/LoRa_APRS_iGate/blob/main/variants/ESP32_DIY_1W_LoRa_Mesh_V1_2/board_pinout.h
+
+*/
+
+// OLED (may be different controllers depending on screen size)
+#define I2C_SDA 21
+#define I2C_SCL 22
+#define HAS_SCREEN 1 // Generates randomized BLE pin
+
+// GNSS: Ai-Thinker GP-02 BDS/GNSS module
+#define GPS_RX_PIN 16
+#define GPS_TX_PIN 17
+
+// Button
+#define BUTTON_PIN 15 // Right side button - if not available, set device.button_gpio to 0 from Meshtastic client
+
+// LEDs
+#define LED_PIN 13 // Tx LED
+#define USER_LED 2 // Rx LED
+
+// Buzzer
+#define PIN_BUZZER 33
+
+// Battery sense
+#define BATTERY_PIN 35
+#define ADC_MULTIPLIER 2.01 // 100k + 100k, and add 1% tolerance
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
+#define BATTERY_SENSE_RESOLUTION_BITS ADC_RESOLUTION
+
+// SPI
+#define LORA_SCK 18
+#define LORA_MISO 19
+#define LORA_MOSI 23
+
+// LoRa
+#define LORA_CS 5
+#define LORA_DIO0 26          // a No connect on the SX1262/SX1268 module
+#define LORA_RESET 27         // RST for SX1276, and for SX1262/SX1268
+#define LORA_DIO1 12          // IRQ for SX1262/SX1268
+#define LORA_DIO2 RADIOLIB_NC // BUSY for SX1262/SX1268
+#define LORA_DIO3             // NC, but used as TCXO supply by E22 module
+#define LORA_RXEN 32          // RF switch RX (and E22 LNA) control by ESP32 GPIO
+#define LORA_TXEN 25          // RF switch TX (and E22 PA) control by ESP32 GPIO
+
+// RX/TX for RFM95/SX127x
+#define RF95_RXEN LORA_RXEN
+#define RF95_TXEN LORA_TXEN
+// #define RF95_TCXO <GPIO#>
+
+// common pinouts for SX126X modules
+#define SX126X_CS 5
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY LORA_DIO2
+#define SX126X_RESET LORA_RESET
+#define SX126X_RXEN LORA_RXEN
+#define SX126X_TXEN LORA_TXEN
+
+// Support alternative modules if soldered in place of E22
+#define USE_RF95 // RFM95/SX127x
+#define USE_SX1262
+#define USE_SX1268
+#define USE_LLCC68
+
+// E22 TCXO support
+#ifdef EBYTE_E22
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+#define TCXO_OPTIONAL // make it so that the firmware can try both TCXO and XTAL
+#endif
@@ -1,6 +1,7 @@
 [env:heltec-wireless-bridge]
 ;build_type = debug ; to make it possible to step through our jtag debugger 
 extends = esp32_base
+board_level = extra
 board = heltec_wifi_lora_32
 build_flags = 
  ${esp32_base.build_flags}
@@ -1,5 +1,6 @@
 [env:trackerd]
 extends = esp32_base
+board_level = extra
 board = pico32
 board_build.f_flash = 80000000L

@@ -2,7 +2,7 @@
 extends = esp32s3_base
 board = bpi_picow_esp32_s3
 board_check = true
-board_build.partitions = default_8MB.csv
+board_build.partitions = partition-table-8MB.csv
 ;OpenOCD flash method
 ;upload_protocol = esp-builtin
 ;Normal method
@@ -26,6 +26,7 @@ extends = env:picomputer-s3

 build_flags =
  ${env:picomputer-s3.build_flags}
+  -D MESHTASTIC_EXCLUDE_WEBSERVER=1
  -D INPUTDRIVER_MATRIX_TYPE=1
  -D USE_PIN_BUZZER=PIN_BUZZER
  -D USE_SX127x
@@ -0,0 +1,28 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include "variant.h"
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// The default Wire will be mapped to PMU and RTC
+static const uint8_t SDA = 9;
+static const uint8_t SCL = 40;
+
+// Default SPI will be mapped to Radio
+static const uint8_t SS = 12;
+static const uint8_t MOSI = 11;
+static const uint8_t MISO = 10;
+static const uint8_t SCK = 13;
+
+#define SPI_MOSI (11)
+#define SPI_SCK (13)
+#define SPI_MISO (10)
+#define SPI_CS (12)
+
+// LEDs
+#define LED_BUILTIN LED_GREEN
+
+#endif /* Pins_Arduino_h */
@@ -0,0 +1,88 @@
+; rak_wismeshtap2 rak3112
+
+[rak_wismeshtap_s3]
+extends = esp32s3_base
+board = wiscore_rak3312
+board_check = true
+upload_protocol = esptool
+board_build.partitions = default_8MB.csv
+
+build_flags = 
+  ${esp32_base.build_flags} 
+  -D RAK3312
+  -D RAK_WISMESH_TAP_V2 
+  -I variants/esp32s3/rak_wismesh_tap_v2
+
+lib_deps =
+  ${esp32s3_base.lib_deps}
+  lovyan03/LovyanGFX@^1.2.0
+
+[ft5x06]
+extends = mesh_tab_base
+build_flags = 
+  -D LGFX_TOUCH=FT5x06
+  -D LGFX_TOUCH_I2C_FREQ=100000
+  -D LGFX_TOUCH_I2C_PORT=0
+  -D LGFX_TOUCH_I2C_ADDR=0x38
+  -D LGFX_TOUCH_I2C_SDA=9
+  -D LGFX_TOUCH_I2C_SCL=40
+  -D LGFX_TOUCH_RST=-1
+  -D LGFX_TOUCH_INT=39
+
+[env:rak_wismesh_tap_v2-tft]
+extends = rak_wismeshtap_s3
+
+build_flags =
+  ${rak_wismeshtap_s3.build_flags}
+  -D CONFIG_ARDUHAL_ESP_LOG
+  -D CONFIG_ARDUHAL_LOG_COLORS=1
+  -D CONFIG_DISABLE_HAL_LOCKS=1
+  -D LV_LVGL_H_INCLUDE_SIMPLE
+  -D LV_CONF_INCLUDE_SIMPLE
+  -D LV_COMP_CONF_INCLUDE_SIMPLE
+  -D LV_USE_SYSMON=0
+  -D LV_USE_PROFILER=0
+  -D LV_USE_PERF_MONITOR=0
+  -D LV_USE_MEM_MONITOR=0
+  -D LV_USE_LOG=0
+  -D LV_BUILD_TEST=0
+  -D USE_LOG_DEBUG
+  -D LOG_DEBUG_INC=\"DebugConfiguration.h\"
+  -D RADIOLIB_SPI_PARANOID=0
+  -D INPUTDRIVER_BUTTON_TYPE=0
+  -D HAS_SDCARD
+  -D HAS_SCREEN=0
+  -D HAS_TFT=1
+  -D USE_PIN_BUZZER=PIN_BUZZER
+  -D RAM_SIZE=5120
+  -D LGFX_DRIVER_TEMPLATE
+  -D LGFX_DRIVER=LGFX_GENERIC
+  -D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_GENERIC.h\"
+  -D LGFX_PIN_SCK=13
+  -D LGFX_PIN_MOSI=11
+  -D LGFX_PIN_MISO=10
+  -D LGFX_PIN_DC=42
+  -D LGFX_PIN_CS=12
+  -D LGFX_PIN_RST=-1
+  -D LGFX_PIN_BL=41
+  -D VIEW_320x240
+  -D USE_PACKET_API
+  ${ft5x06.build_flags}
+  -D LGFX_SCREEN_WIDTH=240
+  -D LGFX_SCREEN_HEIGHT=320
+  -D DISPLAY_SIZE=320x240 ; landscape mode
+  -D LGFX_PANEL=ST7789
+  -D LGFX_ROTATION=1
+  -D LGFX_TOUCH_X_MIN=0
+  -D LGFX_TOUCH_X_MAX=239
+  -D LGFX_TOUCH_Y_MIN=0
+  -D LGFX_TOUCH_Y_MAX=319
+  -D LGFX_TOUCH_ROTATION=2
+  -D LGFX_CFG_HOST=SPI3_HOST
+  -D MAP_FULL_REDRAW=1
+
+lib_deps =
+  ${rak_wismeshtap_s3.lib_deps}
+  ${device-ui_base.lib_deps}
+
+
@@ -0,0 +1,71 @@
+#ifndef _VARIANT_RAK_WISMESHTAP_V2_H
+#define _VARIANT_RAK_WISMESHTAP_V2_H
+
+#define I2C_SDA 9
+#define I2C_SCL 40
+
+#define USE_SX1262
+
+#define LORA_SCK 5
+#define LORA_MISO 3
+#define LORA_MOSI 6
+#define LORA_CS 7
+#define LORA_RESET 8
+
+#ifdef USE_SX1262
+#define SX126X_CS LORA_CS
+#define SX126X_DIO1 47
+#define SX126X_BUSY 48
+#define SX126X_RESET LORA_RESET
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+#endif
+
+#define SX126X_POWER_EN (4)
+
+#define PIN_POWER_EN PIN_3V3_EN
+#define PIN_3V3_EN (14)
+
+#define LED_GREEN 46
+#define LED_BLUE 45
+
+#define PIN_LED1 LED_GREEN
+#define PIN_LED2 LED_BLUE
+
+#define LED_CONN LED_BLUE
+#define LED_PIN LED_GREEN
+#define ledOff(pin) pinMode(pin, INPUT)
+
+#define LED_STATE_ON 1 // State when LED is litted
+
+#define HAS_GPS 1
+#define GPS_TX_PIN 43
+#define GPS_RX_PIN 44
+
+#define SPI_MOSI (11)
+#define SPI_SCK (13)
+#define SPI_MISO (10)
+#define SPI_CS (12)
+
+#define HAS_BUTTON 1
+#define BUTTON_PIN 0
+
+#define CANNED_MESSAGE_MODULE_ENABLE 1
+#define USE_VIRTUAL_KEYBOARD 1
+
+#define BATTERY_PIN 1
+#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
+#define ADC_MULTIPLIER 1.667
+
+#define PIN_BUZZER 38
+
+#define HAS_SDCARD 1
+#define SDCARD_USE_SPI1 1
+#define SDCARD_CS 2
+
+#define SPI_FREQUENCY 40000000
+#define SPI_READ_FREQUENCY 16000000
+
+#define SD_SPI_FREQUENCY 50000000
+
+#endif
@@ -6,7 +6,7 @@ platform_packages =

 board = seeed-sensecap-indicator
 board_check = true
-board_build.partitions = default_8MB.csv
+board_build.partitions = partition-table-8MB.csv
 upload_protocol = esptool

 build_flags = ${esp32_base.build_flags}
@@ -26,7 +26,7 @@ lib_deps = ${esp32s3_base.lib_deps}
  lewisxhe/SensorLib@0.3.1
  https://github.com/pschatzmann/arduino-audio-driver/archive/refs/tags/v0.1.3.zip
  https://github.com/mverch67/BQ27220/archive/07d92be846abd8a0258a50c23198dac0858b22ed.zip
-  https://github.com/mverch67/RotaryEncoder
+  https://github.com/mverch67/RotaryEncoder/archive/25a59d5745a6645536f921427d80b08e78f886d4.zip

 [env:tlora-pager-tft]
 board_level = extra
@@ -3,7 +3,7 @@
 [env:unphone]
 extends = esp32s3_base
 board = unphone
-board_build.partitions = default_8MB.csv
+board_build.partitions = partition-table-8MB.csv
 upload_speed = 921600
 monitor_speed = 115200
 monitor_filters = esp32_exception_decoder
@@ -20,6 +20,7 @@ build_flags =
  -D UNPHONE_LORA=0
  -D UNPHONE_FACTORY_MODE=0
  -D USE_SX127x
+  -D SDCARD_CS=43

 build_src_filter =
  ${esp32s3_base.build_src_filter}
@@ -41,6 +42,7 @@ build_flags =
  -D HAS_SCREEN=1
  -D HAS_TFT=1
  -D HAS_SDCARD
+  -D SDCARD_CS=43
  -D DISPLAY_SET_RESOLUTION
  -D RAM_SIZE=6144
  -D LV_CACHE_DEF_SIZE=2097152
@@ -52,7 +52,6 @@
 #undef GPS_TX_PIN

 #define SD_SPI_FREQUENCY 25000000
-#define SDCARD_CS 43

 #define LED_PIN 13     // the red part of the RGB LED
 #define LED_STATE_ON 0 // State when LED is lit
@@ -1,5 +1,5 @@
 #define HAS_SCREEN 1
 #define CANNED_MESSAGE_MODULE_ENABLE 1
 #define HAS_GPS 1
-#define MAX_RX_TOPHONE settingsMap[maxtophone]
-#define MAX_NUM_NODES settingsMap[maxnodes]
+#define MAX_RX_TOPHONE portduino_config.maxtophone
+#define MAX_NUM_NODES portduino_config.MaxNodes
@@ -3,8 +3,8 @@
 #endif
 #define CANNED_MESSAGE_MODULE_ENABLE 1
 #define HAS_GPS 1
-#define MAX_RX_TOPHONE settingsMap[maxtophone]
-#define MAX_NUM_NODES settingsMap[maxnodes]
+#define MAX_RX_TOPHONE portduino_config.maxtophone
+#define MAX_NUM_NODES portduino_config.MaxNodes

 // RAK12002 RTC Module
-#define RV3028_RTC (uint8_t)0b1010010
+#define RV3028_RTC (uint8_t)0b1010010
@@ -1,6 +1,7 @@
 ; The very slick RAK wireless RAK 4631 / 4630 board - Unified firmware for 5005/19003, with or without OLED RAK 1921
 [env:gat562_mesh_trial_tracker]
 extends = nrf52840_base
+board_level = extra
 board = gat562_mesh_trial_tracker
 board_check = true
 build_flags = ${nrf52840_base.build_flags}
@@ -208,7 +208,7 @@ No longer populated on PCB
 #undef AREF_VOLTAGE
 #define AREF_VOLTAGE 3.0
 #define VBAT_AR_INTERNAL AR_INTERNAL_3_0
-#define ADC_MULTIPLIER (4.99F)
+#define ADC_MULTIPLIER (4.916F)

 #define HAS_RTC 0
 #ifdef __cplusplus
@@ -4,6 +4,7 @@
 [env:meshlink]
 extends = nrf52840_base
 board = meshlink
+board_level = extra
 ;board_check = true
 build_flags = ${nrf52840_base.build_flags}
  -I variants/nrf52840/meshlink
@@ -4,6 +4,7 @@
 [env:meshlink_eink]
 extends = nrf52840_base
 board = meshlink
+board_level = extra
 ;board_check = true
 build_flags = ${nrf52840_base.build_flags}
  -I variants/nrf52840/meshlink_eink
@@ -22,6 +22,7 @@ lib_deps =
  https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip
  rakwireless/RAKwireless NCP5623 RGB LED library@^1.0.2
  beegee-tokyo/RAK12035_SoilMoisture@^1.0.4
+  # renovate: datasource=git-refs depName=RAK12034-BMX160 packageName=https://github.com/RAKWireless/RAK12034-BMX160 gitBranch=main
  https://github.com/RAKWireless/RAK12034-BMX160/archive/dcead07ffa267d3c906e9ca4a1330ab989e957e2.zip

 ; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
@@ -31,7 +31,8 @@ lib_deps =
  melopero/Melopero RV3028@^1.1.0
  https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip
  rakwireless/RAKwireless NCP5623 RGB LED library@^1.0.2
-  https://github.com/meshtastic/RAK12034-BMX160/archive/4821355fb10390ba8557dc43ca29a023bcfbb9d9.zip
+  # renovate: datasource=git-refs depName=RAK12034-BMX160 packageName=https://github.com/RAKWireless/RAK12034-BMX160 gitBranch=main
+  https://github.com/RAKWireless/RAK12034-BMX160/archive/dcead07ffa267d3c906e9ca4a1330ab989e957e2.zip
  bblanchon/ArduinoJson @ 6.21.4
 ; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
 ; Note: as of 6/2013 the serial/bootloader based programming takes approximately 30 seconds
@@ -0,0 +1,79 @@
+#pragma once
+
+#define PINS_COUNT (25u)
+#define NUM_DIGITAL_PINS (25u)
+#define NUM_ANALOG_INPUTS (4u)
+#define NUM_ANALOG_OUTPUTS (0u)
+#define ADC_RESOLUTION (12u)
+
+// LEDs
+#define PIN_LED (24u)
+
+// Serial
+#define PIN_SERIAL1_TX (16u)
+#define PIN_SERIAL1_RX (17u)
+
+// SPI
+#define PIN_SPI0_MISO (20u)
+#define PIN_SPI0_MOSI (23u)
+#define PIN_SPI0_SCK (22u)
+#define PIN_SPI0_SS (21u)
+
+// Connected to LoRa module
+#define PIN_SPI1_MISO (12u)
+#define PIN_SPI1_MOSI (11u)
+#define PIN_SPI1_SCK (10u)
+#define PIN_SPI1_SS (9u)
+#define RFM95W_SS (9u)
+#define RFM95W_DIO0 (14u)
+#define RFM95W_DIO1 (15u)
+#define RFM95W_DIO2 (18u)
+#define RFM95W_RST (13u)
+#define RFM95W_SPI SPI1
+
+// Wire
+#define PIN_WIRE0_SDA (0u)
+#define PIN_WIRE0_SCL (1u)
+
+// Not pinned out
+#define PIN_WIRE1_SDA (31u)
+#define PIN_WIRE1_SCL (31u)
+#define PIN_SERIAL2_RX (31u)
+#define PIN_SERIAL2_TX (31u)
+
+#define SERIAL_HOWMANY (1u)
+#define SPI_HOWMANY (2u)
+#define WIRE_HOWMANY (1u)
+
+#define LED_BUILTIN PIN_LED
+
+static const uint8_t D0 = (16u);
+static const uint8_t D1 = (17u);
+static const uint8_t D2 = (20u);
+static const uint8_t D3 = (23u);
+static const uint8_t D4 = (22u);
+static const uint8_t D5 = (2u);
+static const uint8_t D6 = (3u);
+static const uint8_t D7 = (0u);
+static const uint8_t D8 = (1u);
+static const uint8_t D9 = (4u);
+static const uint8_t D10 = (5u);
+static const uint8_t D11 = (6u);
+static const uint8_t D12 = (7u);
+static const uint8_t D13 = (8u);
+static const uint8_t D14 = (13u);
+static const uint8_t D15 = (14u);
+static const uint8_t D16 = (15u);
+static const uint8_t D17 = (18u);
+static const uint8_t D18 = (24u);
+
+static const uint8_t A0 = (26u);
+static const uint8_t A1 = (27u);
+static const uint8_t A2 = (28u);
+static const uint8_t A3 = (29u);
+static const uint8_t A4 = (19u);
+static const uint8_t A5 = (21u);
+
+#ifndef SS
+#define SS PIN_SPI1_SS
+#endif
@@ -0,0 +1,16 @@
+[env:challenger_2040_lora]
+extends = rp2040_base
+board = challenger_2040_lora
+board_level = extra
+upload_protocol = picotool
+# add our variants files to the include and src paths
+build_flags = 
+  ${rp2040_base.build_flags} 
+  -D PRIVATE_HW
+  -I variants/rp2040/challenger_2040_lora
+  -D DEBUG_RP2040_PORT=Serial
+  -D HW_SPI1_DEVICE
+lib_deps =
+  ${rp2040_base.lib_deps}
+debug_build_flags = ${rp2040_base.build_flags}
+debug_tool = cmsis-dap ; for e.g. Picotool
@@ -0,0 +1,39 @@
+// Define SS for compatibility with libraries expecting a default SPI chip select pin
+
+#define ARDUINO_ARCH_AVR
+
+#define EXT_NOTIFY_OUT 0xFFFFFFFF
+#define BUTTON_PIN 0xFFFFFFFF
+
+#define LED_PIN PIN_LED
+
+#define USE_RF95 // RFM95/SX127x
+
+#undef LORA_SCK
+#undef LORA_MISO
+#undef LORA_MOSI
+#undef LORA_CS
+
+// https://gitlab.com/invectorlabs/hw/challenger_rp2040_lora
+#define LORA_SCK 10  // Clock
+#define LORA_CS 9    // Chip Select
+#define LORA_MOSI 11 // Serial Data Out
+#define LORA_MISO 12 // Serial Data In
+
+#define LORA_RESET 13 // Reset
+
+#define LORA_DIO0 14         // DIO0
+#define LORA_DIO1 15         // DIO1
+#define LORA_DIO2 18         // DIO2
+#define LORA_DIO3 0xFFFFFFFF // Not connected
+#define LORA_DIO4 0xFFFFFFFF // Not connected
+#define LORA_DIO5 0xFFFFFFFF // Not connected
+
+#ifdef USE_SX1262
+#define SX126X_CS LORA_CS
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY LORA_DIO2
+#define SX126X_RESET LORA_RESET
+#define SX126X_DIO2_AS_RF_SWITCH
+// #define SX126X_DIO3_TCXO_VOLTAGE 1.8
+#endif
@@ -1,6 +1,7 @@
 [env:catsniffer]
 extends = rp2040_base
 board = rpipico
+board_level = extra
 upload_protocol = picotool
 build_flags = 
  ${rp2040_base.build_flags}
@@ -12,7 +12,5 @@ build_flags =
  -DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
  -DMESHTASTIC_EXCLUDE_I2C=1
  -DMESHTASTIC_EXCLUDE_GPS=1
-  ;-DPIO_FRAMEWORK_ARDUINO_NANOLIB_FLOAT_PRINTF
-  ;-DCFG_DEBUG

 upload_port = stlink
@@ -0,0 +1,9 @@
+// From E77-900M22S Product Specification
+// https://www.cdebyte.com/pdf-down.aspx?id=2963
+// Note 1: PA6 and PA7 pins are used as internal control RF switches of the module, PA6 = RF_TXEN, PA7 = RF_RXEN, RF_TXEN=1
+// RF_RXEN=0 is the transmit channel, and RF_TXEN=0 RF_RXEN=1 is the receiving channel
+
+static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PA7, PA6, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[4] = {
+    {STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
@@ -18,5 +18,4 @@ Do not expect a working Meshtastic device with this target.
 #define LED_PIN PB4 // LED1
 // #define LED_PIN PB3 // LED2
 #define LED_STATE_ON 1
-
 #endif
@@ -15,5 +15,5 @@ build_flags =
  -DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
  -DMESHTASTIC_EXCLUDE_I2C=1
  -DMESHTASTIC_EXCLUDE_GPS=1
-  ;-DCFG_DEBUG
+
 upload_port = stlink
@@ -0,0 +1,7 @@
+// Pins from https://forum.rakwireless.com/t/rak3172-internal-schematic/4557/2
+// PB8, PC13
+
+static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PB8, PC13, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[4] = {
+    {STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
@@ -0,0 +1,8 @@
+/* https://wiki.seeedstudio.com/LoRa-E5_STM32WLE5JC_Module/
+ * Wio-E5 module ONLY transmits through RFO_HP
+ * Receive: PA4=1, PA5=0
+ * Transmit(high output power, SMPS mode): PA4=0, PA5=1 */
+static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PA4, PA5, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
+
+static const Module::RfSwitchMode_t rfswitch_table[4] = {
+    {STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};