Merge branch 'develop' into clear-rangetest-results

2025-09-09 12:05:00 +12:00
parent c62f262f63 569a911455
commit 87a1449f76
119 changed files with 2197 additions and 909 deletions
@@ -2,7 +2,7 @@
 extends = esp32s3_base
 board = bpi_picow_esp32_s3
 board_check = true
-board_build.partitions = default_8MB.csv
+board_build.partitions = partition-table-8MB.csv
 ;OpenOCD flash method
 ;upload_protocol = esp-builtin
 ;Normal method
@@ -26,6 +26,7 @@ extends = env:picomputer-s3

 build_flags =
  ${env:picomputer-s3.build_flags}
+  -D MESHTASTIC_EXCLUDE_WEBSERVER=1
  -D INPUTDRIVER_MATRIX_TYPE=1
  -D USE_PIN_BUZZER=PIN_BUZZER
  -D USE_SX127x
@@ -0,0 +1,28 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include "variant.h"
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+// The default Wire will be mapped to PMU and RTC
+static const uint8_t SDA = 9;
+static const uint8_t SCL = 40;
+
+// Default SPI will be mapped to Radio
+static const uint8_t SS = 12;
+static const uint8_t MOSI = 11;
+static const uint8_t MISO = 10;
+static const uint8_t SCK = 13;
+
+#define SPI_MOSI (11)
+#define SPI_SCK (13)
+#define SPI_MISO (10)
+#define SPI_CS (12)
+
+// LEDs
+#define LED_BUILTIN LED_GREEN
+
+#endif /* Pins_Arduino_h */
@@ -0,0 +1,88 @@
+; rak_wismeshtap2 rak3112
+
+[rak_wismeshtap_s3]
+extends = esp32s3_base
+board = wiscore_rak3312
+board_check = true
+upload_protocol = esptool
+board_build.partitions = default_8MB.csv
+
+build_flags = 
+  ${esp32_base.build_flags} 
+  -D RAK3312
+  -D RAK_WISMESH_TAP_V2 
+  -I variants/esp32s3/rak_wismesh_tap_v2
+
+lib_deps =
+  ${esp32s3_base.lib_deps}
+  lovyan03/LovyanGFX@^1.2.0
+
+[ft5x06]
+extends = mesh_tab_base
+build_flags = 
+  -D LGFX_TOUCH=FT5x06
+  -D LGFX_TOUCH_I2C_FREQ=100000
+  -D LGFX_TOUCH_I2C_PORT=0
+  -D LGFX_TOUCH_I2C_ADDR=0x38
+  -D LGFX_TOUCH_I2C_SDA=9
+  -D LGFX_TOUCH_I2C_SCL=40
+  -D LGFX_TOUCH_RST=-1
+  -D LGFX_TOUCH_INT=39
+
+[env:rak_wismesh_tap_v2-tft]
+extends = rak_wismeshtap_s3
+
+build_flags =
+  ${rak_wismeshtap_s3.build_flags}
+  -D CONFIG_ARDUHAL_ESP_LOG
+  -D CONFIG_ARDUHAL_LOG_COLORS=1
+  -D CONFIG_DISABLE_HAL_LOCKS=1
+  -D LV_LVGL_H_INCLUDE_SIMPLE
+  -D LV_CONF_INCLUDE_SIMPLE
+  -D LV_COMP_CONF_INCLUDE_SIMPLE
+  -D LV_USE_SYSMON=0
+  -D LV_USE_PROFILER=0
+  -D LV_USE_PERF_MONITOR=0
+  -D LV_USE_MEM_MONITOR=0
+  -D LV_USE_LOG=0
+  -D LV_BUILD_TEST=0
+  -D USE_LOG_DEBUG
+  -D LOG_DEBUG_INC=\"DebugConfiguration.h\"
+  -D RADIOLIB_SPI_PARANOID=0
+  -D INPUTDRIVER_BUTTON_TYPE=0
+  -D HAS_SDCARD
+  -D HAS_SCREEN=0
+  -D HAS_TFT=1
+  -D USE_PIN_BUZZER=PIN_BUZZER
+  -D RAM_SIZE=5120
+  -D LGFX_DRIVER_TEMPLATE
+  -D LGFX_DRIVER=LGFX_GENERIC
+  -D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_GENERIC.h\"
+  -D LGFX_PIN_SCK=13
+  -D LGFX_PIN_MOSI=11
+  -D LGFX_PIN_MISO=10
+  -D LGFX_PIN_DC=42
+  -D LGFX_PIN_CS=12
+  -D LGFX_PIN_RST=-1
+  -D LGFX_PIN_BL=41
+  -D VIEW_320x240
+  -D USE_PACKET_API
+  ${ft5x06.build_flags}
+  -D LGFX_SCREEN_WIDTH=240
+  -D LGFX_SCREEN_HEIGHT=320
+  -D DISPLAY_SIZE=320x240 ; landscape mode
+  -D LGFX_PANEL=ST7789
+  -D LGFX_ROTATION=1
+  -D LGFX_TOUCH_X_MIN=0
+  -D LGFX_TOUCH_X_MAX=239
+  -D LGFX_TOUCH_Y_MIN=0
+  -D LGFX_TOUCH_Y_MAX=319
+  -D LGFX_TOUCH_ROTATION=2
+  -D LGFX_CFG_HOST=SPI3_HOST
+  -D MAP_FULL_REDRAW=1
+
+lib_deps =
+  ${rak_wismeshtap_s3.lib_deps}
+  ${device-ui_base.lib_deps}
+
+
@@ -0,0 +1,71 @@
+#ifndef _VARIANT_RAK_WISMESHTAP_V2_H
+#define _VARIANT_RAK_WISMESHTAP_V2_H
+
+#define I2C_SDA 9
+#define I2C_SCL 40
+
+#define USE_SX1262
+
+#define LORA_SCK 5
+#define LORA_MISO 3
+#define LORA_MOSI 6
+#define LORA_CS 7
+#define LORA_RESET 8
+
+#ifdef USE_SX1262
+#define SX126X_CS LORA_CS
+#define SX126X_DIO1 47
+#define SX126X_BUSY 48
+#define SX126X_RESET LORA_RESET
+#define SX126X_DIO2_AS_RF_SWITCH
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8
+#endif
+
+#define SX126X_POWER_EN (4)
+
+#define PIN_POWER_EN PIN_3V3_EN
+#define PIN_3V3_EN (14)
+
+#define LED_GREEN 46
+#define LED_BLUE 45
+
+#define PIN_LED1 LED_GREEN
+#define PIN_LED2 LED_BLUE
+
+#define LED_CONN LED_BLUE
+#define LED_PIN LED_GREEN
+#define ledOff(pin) pinMode(pin, INPUT)
+
+#define LED_STATE_ON 1 // State when LED is litted
+
+#define HAS_GPS 1
+#define GPS_TX_PIN 43
+#define GPS_RX_PIN 44
+
+#define SPI_MOSI (11)
+#define SPI_SCK (13)
+#define SPI_MISO (10)
+#define SPI_CS (12)
+
+#define HAS_BUTTON 1
+#define BUTTON_PIN 0
+
+#define CANNED_MESSAGE_MODULE_ENABLE 1
+#define USE_VIRTUAL_KEYBOARD 1
+
+#define BATTERY_PIN 1
+#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
+#define ADC_MULTIPLIER 1.667
+
+#define PIN_BUZZER 38
+
+#define HAS_SDCARD 1
+#define SDCARD_USE_SPI1 1
+#define SDCARD_CS 2
+
+#define SPI_FREQUENCY 40000000
+#define SPI_READ_FREQUENCY 16000000
+
+#define SD_SPI_FREQUENCY 50000000
+
+#endif
@@ -6,7 +6,7 @@ platform_packages =

 board = seeed-sensecap-indicator
 board_check = true
-board_build.partitions = default_8MB.csv
+board_build.partitions = partition-table-8MB.csv
 upload_protocol = esptool

 build_flags = ${esp32_base.build_flags}
@@ -26,7 +26,7 @@ lib_deps = ${esp32s3_base.lib_deps}
  lewisxhe/SensorLib@0.3.1
  https://github.com/pschatzmann/arduino-audio-driver/archive/refs/tags/v0.1.3.zip
  https://github.com/mverch67/BQ27220/archive/07d92be846abd8a0258a50c23198dac0858b22ed.zip
-  https://github.com/mverch67/RotaryEncoder
+  https://github.com/mverch67/RotaryEncoder/archive/25a59d5745a6645536f921427d80b08e78f886d4.zip

 [env:tlora-pager-tft]
 board_level = extra
@@ -3,7 +3,7 @@
 [env:unphone]
 extends = esp32s3_base
 board = unphone
-board_build.partitions = default_8MB.csv
+board_build.partitions = partition-table-8MB.csv
 upload_speed = 921600
 monitor_speed = 115200
 monitor_filters = esp32_exception_decoder
@@ -20,6 +20,7 @@ build_flags =
  -D UNPHONE_LORA=0
  -D UNPHONE_FACTORY_MODE=0
  -D USE_SX127x
+  -D SDCARD_CS=43

 build_src_filter =
  ${esp32s3_base.build_src_filter}
@@ -41,6 +42,7 @@ build_flags =
  -D HAS_SCREEN=1
  -D HAS_TFT=1
  -D HAS_SDCARD
+  -D SDCARD_CS=43
  -D DISPLAY_SET_RESOLUTION
  -D RAM_SIZE=6144
  -D LV_CACHE_DEF_SIZE=2097152
@@ -52,7 +52,6 @@
 #undef GPS_TX_PIN

 #define SD_SPI_FREQUENCY 25000000
-#define SDCARD_CS 43

 #define LED_PIN 13     // the red part of the RGB LED
 #define LED_STATE_ON 0 // State when LED is lit