feat: add WIZnet W5500-EVB-Pico2 + E22P-868M30S variant (#10552)
* feat: add WIZnet W5500-EVB-Pico2 + E22P-868M30S variant Adds a community variant for the WIZnet W5500-EVB-Pico2 development board (https://docs.wiznet.io/Product/iEthernet/W5500/w5500-evb-pico2) paired with an external EBYTE E22P-868M30S LoRa module. This is the hardware twin of variants/rp2350/diy/pico2_w5500_e22 — same LoRa pinout, same W5500 pin mapping — and reuses its variant.h verbatim via `-I variants/rp2350/diy/pico2_w5500_e22`. No duplicated pinout file. Two differences vs pico2_w5500_e22 justify the separate env: 1. Board target: `wiznet_5500_evb_pico2` (2 MB flash) instead of `rpipico2` (4 MB flash). The WIZnet PCB ships with a smaller Q-SPI chip than a stock Pi Pico 2. Selecting the correct board makes the linker fail fast on overflow instead of producing a UF2 that gets silently truncated when flashed to the device. 2. W5500 PHY is integrated on the PCB (hard-wired SPI0 GP16-20) rather than supplied as an external module the user wires manually. The E22P-868M30S uses a single combined RFEN pin (LNA + PA enable) instead of the older E22-900M30S's split RXEN/TXEN pins. RFEN is held HIGH at all times via `SX126X_ANT_SW 3`; TX switching still uses the on-module DIO2 → TXEN bridge through `SX126X_DIO2_AS_RF_SWITCH`. Build verified: wiznet_5500_evb_pico2_e22p SUCCESS (RAM 19.2%, Flash 65.6% of 1.5 MB partition / 2 MB chip). * style(wiznet-evb-pico2-e22p): prettier-format README tables --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
This commit is contained in:
Carlos Valdes
co-authored by
GitHub
Ben Meadors
GitHub
Ben Meadors
parent
e3ae0a6ab5
commit
ce7444c1a1
@@ -0,0 +1,160 @@
|
|||||||
|
# WIZnet W5500-EVB-Pico2 + E22P-868M30S — Meshtastic Variant
|
||||||
|
|
||||||
|
Meshtastic support for the **WIZnet W5500-EVB-Pico2**, a Raspberry Pi Pico 2 development board with an **integrated W5500 Ethernet PHY** on SPI0, paired with an external **EBYTE E22P-868M30S** LoRa module on SPI1.
|
||||||
|
|
||||||
|
This variant is hardware-twin of [`pico2_w5500_e22`](../diy/pico2_w5500_e22/) (same LoRa pinout, same W5500 pin mapping) but targets the WIZnet PCB rather than a standalone Pico 2 + external W5500 module. The two key differences are:
|
||||||
|
|
||||||
|
| | `pico2_w5500_e22` | `wiznet_5500_evb_pico2_e22p` |
|
||||||
|
| ------------ | -------------------------------------- | ---------------------------------------- |
|
||||||
|
| Board target | `rpipico2` (4 MB flash) | `wiznet_5500_evb_pico2` (**2 MB flash**) |
|
||||||
|
| W5500 PHY | External breakout module (you wire it) | Integrated on the PCB (hard-wired) |
|
||||||
|
|
||||||
|
> ⚠️ Flashing a W5500-EVB-Pico2 with the `pico2_w5500_e22` env builds for a 4 MB flash target and can silently overflow the 2 MB available on the WIZnet PCB. Use this variant for the WIZnet board.
|
||||||
|
|
||||||
|
The LoRa wiring and `variant.h` are shared with `diy/pico2_w5500_e22` via `-I variants/rp2350/diy/pico2_w5500_e22` — there is no duplicated pinout file.
|
||||||
|
|
||||||
|
---
|
||||||
|
|
||||||
|
## Required Hardware
|
||||||
|
|
||||||
|
| Component | Model | Notes |
|
||||||
|
| --------- | ---------------------- | ------------------------------------------------------------------------------ |
|
||||||
|
| Board | WIZnet W5500-EVB-Pico2 | RP2350 @ 150 MHz, 512 KB RAM, **2 MB flash**, on-board W5500 |
|
||||||
|
| LoRa | EBYTE E22P-868M30S | SX1262 + 30 dBm PA, 868 MHz (Europe band); RFEN combines LNA + PA enable lines |
|
||||||
|
|
||||||
|
The W5500-EVB-Pico2 carries a smaller Q-SPI flash (2 MB) than a stock Pi Pico 2 (4 MB). The board target `wiznet_5500_evb_pico2` selects the correct flash size so the linker fails fast if the image overflows, instead of producing a UF2 that gets truncated when flashed to the device.
|
||||||
|
|
||||||
|
---
|
||||||
|
|
||||||
|
## Pinout
|
||||||
|
|
||||||
|
### System pins (W5500-EVB-Pico2, fixed by the PCB)
|
||||||
|
|
||||||
|
| GPIO | Function |
|
||||||
|
| ---- | --------------------------------------- |
|
||||||
|
| GP24 | VBUS sense — HIGH when USB is connected |
|
||||||
|
| GP25 | User LED (heartbeat) |
|
||||||
|
| GP29 | ADC3 — VSYS/3, measures supply voltage |
|
||||||
|
|
||||||
|
### W5500 Ethernet (SPI0, on-board)
|
||||||
|
|
||||||
|
| W5500 signal | RP2350 GPIO |
|
||||||
|
| ------------ | ----------- |
|
||||||
|
| MISO | GP16 |
|
||||||
|
| CS / SCS | GP17 |
|
||||||
|
| SCK | GP18 |
|
||||||
|
| MOSI | GP19 |
|
||||||
|
| RST | GP20 |
|
||||||
|
| INT | GP21 |
|
||||||
|
| VCC | 3.3V |
|
||||||
|
| GND | GND |
|
||||||
|
|
||||||
|
> All Ethernet pins are wired by the PCB — nothing to solder. SPI0 is reserved for the W5500.
|
||||||
|
|
||||||
|
### E22P-868M30S LoRa (SPI1, external)
|
||||||
|
|
||||||
|
| E22P signal | RP2350 GPIO | Notes |
|
||||||
|
| ----------- | ----------- | ------------------------------------------------- |
|
||||||
|
| SCK | GP10 | SPI1 clock |
|
||||||
|
| MOSI | GP11 | SPI1 TX |
|
||||||
|
| MISO | GP12 | SPI1 RX |
|
||||||
|
| NSS / CS | GP13 | Chip select |
|
||||||
|
| RESET | GP15 | Active LOW reset |
|
||||||
|
| DIO1 | GP14 | IRQ interrupt |
|
||||||
|
| BUSY | GP2 | Module busy indicator |
|
||||||
|
| RFEN | GP3 | Combined LNA + PA enable — held HIGH at all times |
|
||||||
|
| TXEN | ← DIO2 | Bridge on the module (see below) |
|
||||||
|
| VCC | 3.3V | Add a 100 µF capacitor close to the module |
|
||||||
|
| GND | GND | — |
|
||||||
|
|
||||||
|
---
|
||||||
|
|
||||||
|
## E22**P** vs E22 — what changed
|
||||||
|
|
||||||
|
The E22**P**-868M30**S** is the newer revision of EBYTE's 30 dBm 868 MHz module. The pinout is interchangeable with the E22-900M30S but the RF switch control differs:
|
||||||
|
|
||||||
|
- On the older E22-900M30S, **RXEN** enables the LNA and **TXEN** enables the PA (two separate pins).
|
||||||
|
- On the E22**P**-868M30**S**, both functions are merged into a single **RFEN** pin acting as a global RF enable. RFEN must be held HIGH whenever the radio is active — both during RX and TX.
|
||||||
|
|
||||||
|
The firmware drives this with `SX126X_ANT_SW 3`, which sets GP3 (RFEN) HIGH once at boot and leaves it there. TXEN switching during transmit is still handled by the on-module DIO2 → TXEN bridge (see below).
|
||||||
|
|
||||||
|
---
|
||||||
|
|
||||||
|
## Special wiring: DIO2 → TXEN bridge on the E22P module
|
||||||
|
|
||||||
|
The E22P-868M30S does **not** connect DIO2 to the TXEN pin of its PA internally. They must be bridged with a short wire or solder bridge **on the module itself**:
|
||||||
|
|
||||||
|
```text
|
||||||
|
E22P DIO2 pin ──┐
|
||||||
|
├── wire / solder bridge on the module
|
||||||
|
E22P TXEN pin ──┘
|
||||||
|
```
|
||||||
|
|
||||||
|
With this bridge in place, `SX126X_DIO2_AS_RF_SWITCH` causes the SX1262 to drive DIO2 HIGH automatically during TX, enabling the PA without needing an RP2350 GPIO for TXEN.
|
||||||
|
|
||||||
|
**Without this bridge the module will not transmit.**
|
||||||
|
|
||||||
|
---
|
||||||
|
|
||||||
|
## Build
|
||||||
|
|
||||||
|
```bash
|
||||||
|
pio run -e wiznet_5500_evb_pico2_e22p
|
||||||
|
```
|
||||||
|
|
||||||
|
### Flash — BOOTSEL mode
|
||||||
|
|
||||||
|
1. Hold the **BOOTSEL** button on the W5500-EVB-Pico2.
|
||||||
|
2. Connect USB to the PC — it appears as a `RPI-RP2` storage drive.
|
||||||
|
3. Copy the `.uf2` file:
|
||||||
|
|
||||||
|
```text
|
||||||
|
.pio/build/wiznet_5500_evb_pico2_e22p/firmware-wiznet_5500_evb_pico2_e22p-*.uf2
|
||||||
|
```
|
||||||
|
|
||||||
|
Or directly with picotool:
|
||||||
|
|
||||||
|
```bash
|
||||||
|
pio run -e wiznet_5500_evb_pico2_e22p -t upload
|
||||||
|
```
|
||||||
|
|
||||||
|
---
|
||||||
|
|
||||||
|
## Network usage
|
||||||
|
|
||||||
|
This board uses Ethernet (no Wi-Fi). From the Meshtastic app:
|
||||||
|
|
||||||
|
- **Enable Ethernet** under `Config → Network → Ethernet Enabled`
|
||||||
|
- **DHCP** by default; static IP can also be configured
|
||||||
|
|
||||||
|
Services available once connected:
|
||||||
|
|
||||||
|
| Service | Details |
|
||||||
|
| ------- | --------------------------- |
|
||||||
|
| NTP | Time synchronization |
|
||||||
|
| MQTT | Messages to external broker |
|
||||||
|
| API | TCP socket on port 4403 |
|
||||||
|
| Syslog | Remote logging (optional) |
|
||||||
|
|
||||||
|
---
|
||||||
|
|
||||||
|
## Technical notes
|
||||||
|
|
||||||
|
### LoRa — RF control
|
||||||
|
|
||||||
|
| Define | Effect |
|
||||||
|
| ------------------------------ | ----------------------------------------------------------- |
|
||||||
|
| `SX126X_ANT_SW 3` | GP3 (RFEN) driven HIGH at init and never toggled again |
|
||||||
|
| `SX126X_DIO2_AS_RF_SWITCH` | SX1262 drives DIO2 HIGH during TX → enables TXEN via bridge |
|
||||||
|
| `SX126X_DIO3_TCXO_VOLTAGE 1.8` | E22P TCXO controlled by DIO3 |
|
||||||
|
| `-D EBYTE_E22_900M30S` | Sets `TX_GAIN_LORA=7`, max power 22 dBm |
|
||||||
|
|
||||||
|
### Ethernet
|
||||||
|
|
||||||
|
- Library: `arduino-libraries/Ethernet@^2.0.2` (supports W5100/W5200/W5500 auto-detection).
|
||||||
|
- SPI0 is explicitly initialized with pins GP16/18/19 before `Ethernet.init()`.
|
||||||
|
- DHCP timeout is set to 10 s (instead of the default 60 s) to avoid blocking LoRa startup.
|
||||||
|
|
||||||
|
### HW_VENDOR
|
||||||
|
|
||||||
|
Mapped to `meshtastic_HardwareModel_PRIVATE_HW` — no dedicated model exists in the Meshtastic protobuf for this hardware combination.
|
||||||
@@ -0,0 +1,29 @@
|
|||||||
|
[env:wiznet_5500_evb_pico2_e22p]
|
||||||
|
extends = rp2350_base
|
||||||
|
board = wiznet_5500_evb_pico2
|
||||||
|
board_level = community
|
||||||
|
upload_protocol = picotool
|
||||||
|
|
||||||
|
# Reuses the variant.h from variants/rp2350/diy/pico2_w5500_e22 — same LoRa
|
||||||
|
# pinout, same W5500 pin mapping. The only differences vs pico2_w5500_e22 are
|
||||||
|
# the board target (this PCB has 2 MB flash instead of 4 MB) and the W5500
|
||||||
|
# being soldered on-board instead of an external module.
|
||||||
|
build_flags =
|
||||||
|
${rp2350_base.build_flags}
|
||||||
|
-ULED_BUILTIN # avoid "LED_BUILTIN redefined" warnings from framework common.h
|
||||||
|
-I variants/rp2350/diy/pico2_w5500_e22
|
||||||
|
-D HW_SPI1_DEVICE
|
||||||
|
-D EBYTE_E22_900M30S # selects the EBYTE E22(P)-900M30S(S) module config, including TCXO voltage support and TX gain / max power settings
|
||||||
|
|
||||||
|
# Re-enable Ethernet and API source paths excluded in rp2350_base
|
||||||
|
build_src_filter = ${rp2350_base.build_src_filter} +<mesh/eth/> +<mesh/api/> +<mqtt/>
|
||||||
|
|
||||||
|
lib_deps =
|
||||||
|
${rp2350_base.lib_deps}
|
||||||
|
${networking_base.lib_deps}
|
||||||
|
${networking_extra.lib_deps}
|
||||||
|
# Standard WIZnet Ethernet library — supports W5100/W5200/W5500 auto-detect
|
||||||
|
arduino-libraries/Ethernet@^2.0.2
|
||||||
|
|
||||||
|
debug_build_flags = ${rp2350_base.build_flags}, -g
|
||||||
|
debug_tool = cmsis-dap
|
||||||
Reference in New Issue
Block a user