feat: add new configuration files for LR11xx variants (#9761)

* feat: add new configuration files for LR11xx variants

* style: reformat RF switch mode table for improved readability

bin/config.d/femtofox/femtofox_E80-900M2213S.yaml

@@ -0,0 +1,30 @@
+---
+Lora:
+## Ebyte E80-900M22S
+## This is a bit experimental
+## 
+##
+  Module: lr1121
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO3_TCXO_VOLTAGE: 1.8
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1
+
+
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+  
+rfswitch_table:
+  pins: [DIO5, DIO6, DIO7]
+  MODE_STBY: [LOW, LOW, LOW]
+  MODE_RX: [LOW, HIGH, LOW]
+  MODE_TX: [HIGH, HIGH, LOW]
+  MODE_TX_HP: [HIGH, LOW, LOW]
+  MODE_TX_HF: [LOW, LOW, LOW]
+  MODE_GNSS: [LOW, LOW, HIGH]
+  MODE_WIFI: [LOW, LOW, LOW]
+
+General:
+  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_LR1121 generic.yaml

@@ -0,0 +1,46 @@
+---
+Lora:
+## Ebyte E80-900M22S
+## This is a bit experimental
+## 
+##
+  Module: lr1121
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO3_TCXO_VOLTAGE: 1.8
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1
+
+
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+  
+rfswitch_table:
+  pins:
+    - DIO5
+    - DIO6
+  MODE_STBY:
+    - LOW
+    - LOW
+  MODE_RX:
+    - HIGH
+    - LOW
+  MODE_TX:
+    - HIGH
+    - HIGH
+  MODE_TX_HP:
+    - LOW
+    - HIGH
+  MODE_TX_HF:
+    - LOW
+    - LOW
+  MODE_GNSS:
+    - LOW
+    - LOW
+  MODE_WIFI:
+    - LOW
+    - LOW
+
+General:
+  MACAddressSource: eth0

bin/config.d/femtofox/femtofox_WIO-LR1121.yaml

@@ -0,0 +1,30 @@
+---
+Lora:
+## Ebyte E80-900M22S
+## This is a bit experimental
+## 
+##
+  Module: lr1121
+  gpiochip: 1 # subtract 32 from the gpio numbers
+  DIO3_TCXO_VOLTAGE: 1.8
+  CS: 16 #pin6 / GPIO48 1C0
+  IRQ: 23  #pin17 / GPIO55 1C7
+  Busy: 22 #pin16 / GPIO54 1C6
+  Reset: 25 #pin13 / GPIO57 1D1
+
+
+  spidev: spidev0.0 #pins are (CS=16, CLK=17, MOSI=18, MISO=19)
+  spiSpeed: 2000000
+  
+rfswitch_table:
+  pins: [DIO5, DIO6, DIO7]
+  MODE_STBY: [LOW, LOW, LOW]
+  MODE_RX: [LOW, LOW, LOW]
+  MODE_TX: [LOW, HIGH, LOW]
+  MODE_TX_HP: [HIGH, LOW, LOW]
+  # MODE_TX_HF: []
+  # MODE_GNSS: []
+  MODE_WIFI: [LOW, LOW, LOW]
+
+General:
+  MACAddressSource: eth0

variants/nrf52840/diy/nrf52_promicro_diy_tcxo/rfswitch.h

@@ -12,9 +12,15 @@ static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11
                                              RADIOLIB_NC};
 
 static const Module::RfSwitchMode_t rfswitch_table[] = {
-    // mode                  DIO5  DIO6  DIO7
+    // clang-format off
-    {LR11x0::MODE_STBY, {LOW, LOW, LOW}},  {LR11x0::MODE_RX, {LOW, HIGH, LOW}},
+    // mode            DIO5  DIO6  DIO7
-    {LR11x0::MODE_TX, {HIGH, HIGH, LOW}},  {LR11x0::MODE_TX_HP, {HIGH, LOW, LOW}},
+    {LR11x0::MODE_STBY, {LOW, LOW, LOW}},
-    {LR11x0::MODE_TX_HF, {LOW, LOW, LOW}}, {LR11x0::MODE_GNSS, {LOW, LOW, HIGH}},
+    {LR11x0::MODE_RX, {LOW, HIGH, LOW}},
-    {LR11x0::MODE_WIFI, {LOW, LOW, LOW}},  END_OF_MODE_TABLE,
+    {LR11x0::MODE_TX, {HIGH, HIGH, LOW}},
+    {LR11x0::MODE_TX_HP, {HIGH, LOW, LOW}},
+    {LR11x0::MODE_TX_HF, {LOW, LOW, LOW}},
+    {LR11x0::MODE_GNSS, {LOW, LOW, HIGH}},
+    {LR11x0::MODE_WIFI, {LOW, LOW, LOW}},
+    END_OF_MODE_TABLE,
+    // clang-format on
 };