* feat: add Raspberry Pi Pico 2 + W5500 + E22-900M30S variant
Adds community variant for Raspberry Pi Pico 2 (RP2350, 4 MB flash)
with external WIZnet W5500 Ethernet module and EBYTE E22-900M30S LoRa
module (SX1262, 30 dBm PA, 868/915 MHz).
Key details:
- LoRa on SPI1: GP10/11/12/13 (SCK/MOSI/MISO/CS), RST=GP15,
DIO1=GP14, BUSY=GP2, RXEN=GP3 (held HIGH via SX126X_ANT_SW)
- W5500 on SPI0: GP16/17/18/19/20 (MISO/CS/SCK/MOSI/RST)
- SX126X_DIO2_AS_RF_SWITCH: DIO2→TXEN bridge on module handles PA
- SX126X_DIO3_TCXO_VOLTAGE 1.8: TCXO support via EBYTE_E22 flags
- DHCP timeout reduced to 10 s to avoid blocking LoRa startup
- GPS on UART1/Serial2: GP8 TX, GP9 RX
- Reuses WIZNET_5500_EVB_PICO2 code paths for Ethernet init
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* pico2_w5500_e22: rename define and address review feedback
Rename WIZNET_5500_EVB_PICO2 to PICO2_W5500_E22 so the variant-specific
define matches the variant directory name and isn't confused with an
on-board EVB SKU.
Review fixes from PR #10135:
- Gate the 10 s Ethernet DHCP timeout behind PICO2_W5500_E22 so other
Ethernet builds keep the default 60 s behavior; apply the same timeout
to reconnectETH() for consistency.
- Drop the unused -D EBYTE_E22 flag; EBYTE_E22_900M30S already selects
TX_GAIN_LORA / SX126X_MAX_POWER in src/configuration.h.
- Rewrite "on-board W5500" comments to describe the external module.
- Correct README TX_GAIN_LORA value (7, not 10) and drop the EBYTE_E22
row.
* fix(pico2_w5500_e22): drop DEBUG_RP2040_PORT=Serial
The arduino-pico framework hooks _write() when DEBUG_RP2040_PORT=Serial
is set and dumps raw debug bytes onto USB CDC, corrupting any binary
protobuf stream sent through StreamAPI (e.g. `meshtastic --port COMx`).
The variant excludes BT and WiFi, so the primary client transport is
Ethernet TCP via ethServerAPI — unaffected — but users who configure
the node over USB serial would see protobuf decode failures from
debug-byte interleaving. Removing the flag restores clean USB CDC.
Debug output can still be enabled per-build by adding -D DEBUG_RP2040_PORT=Serial1
to redirect to UART0 instead of USB CDC.
* style(pico2_w5500_e22): apply trunk fmt — fixes Trunk Check
- variant.h: clang-format 16.0.3 (drop manual #define alignment)
- README.md: prettier + add `text` language to fenced code blocks (markdownlint MD040)
- wiring.svg: svgo optimization
Resolves the Trunk Check Runner failure on this PR (3 unformatted
files + 8 markdownlint issues). No functional changes.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* refactor(pico2_w5500_e22): address review — move to rp2350/diy, generic guards
Maintainer feedback from NomDeTom on PR #10135:
- Move the variant from variants/rp2350/ to variants/rp2350/diy/ to
distinguish DIY from prebuilt boards (matches the variants/*/diy/
pattern; still discovered via the existing variants/*/diy/*/platformio.ini
glob in the root platformio.ini).
- Replace the board-name macro PICO2_W5500_E22 in shared code with a
generic capability macro USE_ARDUINO_ETHERNET, defined from variant.h.
DebugConfiguration.h / ethServerAPI.h / ethClient.cpp no longer
reference a board name.
- Drop the architecture.h hook entirely: variant.h now defines PRIVATE_HW,
which the existing `#elif defined(PRIVATE_HW)` branch already handles.
No functional change. Build verified: pico2_w5500_e22 SUCCESS
(RAM 19.2%, Flash 28.1%).
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* chore(pico2_w5500_e22): drop unoptimized wiring.svg to fix trunk fmt check
---------
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* rename variant and add guard macros
* older G3 operational. M7 next.
* Split out G3 and M7 to different variants. Completely new PCB design. The G3 stays on 'PRIVATE_HW'
* Define button behaviour and use all of the device flash
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: caveman99 <25002+caveman99@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Resolve naming conflict of Syslog class with namespace
* do not include libpax headers if pax counter is excluded
* clean only top-level sdkconfigs, keep them in the variants directories
* Fix code formatting
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
* bug #4184: fix config file loss due to filesystem write errors
* Use SafeFile for atomic file writing (with xor checksum readback)
* Write db.proto last because it could be the largest file on the FS (and less critical)
* Don't keep a tmp file around while writing db.proto (because too big to fit two files in the filesystem)
* generate a new critial fault if we encounter errors writing to flash
either CriticalErrorCode_FLASH_CORRUPTION_RECOVERABLE or CriticalErrorCode_FLASH_CORRUPTION_UNRECOVERABLE
(depending on if the second write attempt worked)
* reformat the filesystem if we detect it is corrupted (then rewrite our config files) (only on nrf52 - not sure
yet if we should bother on ESP32)
* If we have to format the FS, make sure to preserve the oem.proto if it exists
* add logLegacy() so old C code in libs can log via our logging
* move filesList() to a better location (used only in developer builds)
* Reformat with "trunk fmt" to match our coding conventions
* for #4395: don't use .exists() to before attempting file open
If a LFS filesystem is corrupted, .exists() can fail when a mere .open()
attempt would have succeeded. Therefore better to do the .open() in hopes that
we can read the file (in case we need to reformat to fix the FS).
(Seen and confirmed in stress testing)
* for #4395 more fixes, see below for details:
* check for LFS assertion failures during file operations (needs customized lfs_util.h to provide suitable hooks)
* Remove fsCheck() because checking filesystem by writing to it is very high risk, it makes likelyhood that we will
be able to read the config protobufs quite low.
* Update the LFS inside of adafruitnrf52 to 1.7.2 (from their old 1.6.1) to get the following fix:
https://github.com/littlefs-project/littlefs/commit/97d8d5e96a7781596708664f18f2ea6c3a179330
* use disable_adafruit_usb.py now that we are (temporarily?) using a forked adafruit lib
We need to reach inside the adafruit project and turn off USE_TINYUSB, just doing that
from platformio.ini is no longer sufficient.
Tested on a wio-sdk-wm1110 board (which is the only board that had this problem)
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
While working on #4378 I noticed a funny problem: the blinking system
LED was on during deep-sleep. Initially I thought it was some weird
sleep hw config thing but it turns out it was easier but more pervasive.
We had two different preprocessor symbols which both meant approximately the same
thing LED_INVERTED and LED_STATE_ON (though their polarity was opposite).
Some variant files were setting one, others were setting the other, and others were
setting both. heh.
In the case of the board I was testing (seeed tracker wio 1100) it was only setting one
and the default behavior for the other (for all boards) was incorrect. So I did a grep
and it seems like LED_STATE_ON was used more often, so I kept that one and removed
LED_INVERTED everywhere.
* MESHTASTIC_EXCLUDE_WIFI and HAS_WIFI cleanup...
Our code was checking HAS_WIFI and the new MESHTASTIC_EXCLUDE_WIFI
flags in various places (even though EXCLUDE_WIFI forces HAS_WIFI
to 0). Instead just check HAS_WIFI, only use EXCLUDE_WIFI inside
configuration.h
* cleanup: use HAS_NETWORKING instead of HAS_WIFI || HAS_ETHERNET
We already had HAS_NETWORKING as flag in MQTT to mean 'we have
tcpip'. Generallize that and move it into configuration.h so that
we can use it elsewhere.
* Use #pragma once, because supported by gcc and all modern compilers
instead of #ifdef DOTHFILE_H etc...
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* fix my botched merge - keep board_level = extra flag for rak3631_dbg
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
This shaves roughly 60k from firmware builds by not including the Logging Ressource strings. Define in variant.h or architecture.h
Stats from T-ECHO compiles:
Before:
Flash: [======== ] 81.5% (used 664700 bytes from 815104 bytes)
After:
Flash: [======= ] 74.5% (used 606924 bytes from 815104 bytes)
* compiling w/o e-ink display
* pinout changes
* progress getting LoRa and LCD working
* fix for bootloader, gps pins
* add canary to build matrix
* merge with main
* fix build by excluding BellModem in RadioLib
* fixes for GPS
* Fix LED_BLUE and GPS RX/TX pins
* Variant changes for merge
* make GPS baud rate configurable
* fix debug config
* Canary v1.2 changes
* Fixes for GPS
* pass trunk check
* bump protobufs to master
* update build flags to use CANARYONE enum
* use canaryone throughout for consistency.
* #define 0 is still defined
* add back .vscode/extensions.json
* bump protobufs
* revert manual change to generated file
---------
Co-authored-by: Steven Osborn <steven@lolsborn.com>
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* lay groundwork for a possible future architecture
* switch from feature opt-out to feature opt-in
* lay groundwork for a possible future architecture
* switch from feature opt-out to feature opt-in
* fix USE_RTC in variant.h for rak4631_epaper and t-echo
* ensure Screen.h is not included without configuration.h
Co-authored-by: Peter Lawrence <12226419+majbthrd@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
TomandGitHub
Martin EmrichandGitHub
JorropoandGitHub
IhorNehrutsaandGitHub
GUVWAF
