* Show ExternalNotification as excluded if it is
* Enable ExternalNotification, SerialModule and RangeTest on STM32WL
* Misc fixes for #7797 - ARCH_STM32 -> ARCH_STM32WL, use less flash by dropping weather station support for serialmodule, set tx/rx pins before begin
* Enable Serial1 on RAK3172, make SerialModule use it (console is on LPUART1)
* Fix SerialModule on RAK3172, fix board definition of RAK3172 to include the right pin mapping.
* Fix GPS that hard code 2080 as the start time.
Some GPS chips, such as the AG3335 in T1000e and L96 have a hardcoded
time of 2080-01-05 when they start up.
To fix that in a way that seems permanent, let's ignore times that
are more than 40 years since the firmware was built. We should followup
in late 2039 to see if any changes are needed.
Reported-By: @b8b8
* Update src/gps/RTC.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Put FORTY_YEARS in header and use in both places.
* Restore Ben's nicer log lines.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Hold for >20s after GPS lock
GPS chips are designed to stay locked for a while to download some data and save it.
This data is important for speeding up future locks, and making them higher quality.
Our present configuration could make every lock perform similar to first lock.
This patch sets a hold of between 20s and 10% of the lock search time after lock
is acquired. This should allow the GPS to finish its work before we turn it off.
Fixes https://github.com/meshtastic/firmware/issues/7466
* Remove T1000E-specific GPS holds
The new code does the same thing, for all devices.
* Fix publishing settings
* Cleanups, removing unused variables.
* ifdef log line with GPS_DEBUG
* fixQual is not a bool.
Further to https://github.com/meshtastic/firmware/pull/7772 ,
we discovered that some RTCs have hard-coded start times well in the
past.
This patch gives RTCs the same treatment as GPS - if the time is
earlier than BUILD_EPOCH, we don't use it.
Fixes#7771Fixes#7750
There are certain GPS chips that have a hard-coded time in firmware
that they will return before lock. We set our own hard-coded time,
BUILD_EPOCH, that should be newer and use the comparison to not set
a bad time.
In https://github.com/meshtastic/firmware/pull/7261 we introduced
the RTCSetResult and improved it in https://github.com/meshtastic/firmware/pull/7375 .
However, the original try-fix left logic in GPS.cpp that could
still result in broadcasting the bad time.
Further, as part of our fix we cleared the GPS buffer if we didn't
get a good time. The mesh was hurting at the time, so this was a reasonable
approach. However, given time tends to come in when we're trying to get
early lock, this had the potential side effect of throwing away valuable
information to get position lock.
This change reverses the clearBuffer and changes the logic so if time
is not set it will not be broadcast.
Fixes https://github.com/meshtastic/firmware/issues/7771
Fixes https://github.com/meshtastic/firmware/issues/7750
* Only send Neighbours if we have some to send.
The original intent of NeighborInfo was that when a NeighbourInfo
was sent all of the nodes that saw it would reply with NeighbourInfo.
So, NeighbourInfo was sent even if there were no hop-zero nodes in
the NodeDB.
Since 2023, when this was implemented, our understanding of running city-wide
meshes has improved substantially. We have taken steps to reduce the impact
of NeighborInfo over LoRa.
This change aligns with those ideas: we will now only send NeighborInfo
if we have some neighbors to contribute.
The impact of this change is that a node must first see another directly
connected node in another packet type before NeighborInfo is sent. This means
that a node with no neighbors is no longer able to trigger other nodes
to broadcast NeighborInfo. It will, however, receive the regular periodic
broadcast of NeighborInfo, and will be able to send NeighborInfo if it
has at least 1 neighbor.
* Include all the things
* AvOid memleak
* Add BaseUI support for L1 EInk
* Fix Eink offset
* Add joystick
* Updates
* Adjust Seeed Wio Tracker L1 E-Ink variant (#7326)
* Rename variant
Needs the -inkhud suffix to work correctly with the web flasher
* Display driver for ZJY122250_0213BAAMFGN
* Remove dead code from nicheGraphics.h
Remnants of T-Echo's nicheGraphics.h file, which was used as a template.
* Use ZJY122250_0213BAAMFGN driver
Improves display health. We don't need as many full refreshes now.
* Tidying
* board_check = true
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Consolidation
* Add hack for existing InkHUD button functionality
---------
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
* Add on-screen keyboard implementation on Wio Tracker L1.
* Update On-Screen Keyboard to new layout.
* The on-screen keyboard dynamically adjusts the key size based on the screen.
* Improve input box display on small screens.
* Optimize the virtual keyboard layout and cursor movement logic, and adjust the keyboard starting position for small and wide screens.
* Optimize the text alignment of numeric keys on ssd1306.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Chloe BethelandBen Meadors
Jonathan BennettandBen Meadors
Jason PandBen Meadors
ManuelandGitHub
GUVWAFandGitHub
