* Use hash table for O(1) lookup of recently seen packets
* Eliminate a packet lookup during deduplication
* Infinite loop checks for find and remove
* Consolidate conditional compilation
* Exclude hash table from minimal build
* Additional comment on hash table capacity
* Unit tests for packet history changes
* Update incorrect comment about size clamp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Const
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* PhoneAPI: add missing tak_tag case + skip reserved gap in module-config iteration
The STATE_SEND_MODULECONFIG state machine iterates config_state through
ModuleConfigType enum values (1..MAX+1 = 16) and switches on
meshtastic_ModuleConfig_*_tag values. Two of the resulting tag values
land in the default / LOG_ERROR path:
1. `tak_tag` (16) — the meshtastic_ModuleConfig_TAKConfig struct exists
in the protobuf and has a `.tak` member in payload_variant, but no
PhoneAPI case ever sends it to the phone. As a result, Android
clients can't read the persisted TAK (Team Awareness Kit) module
config at all. Added case that sends moduleConfig.tak, matching the
pattern used for all other module-config tags (paxcounter,
traffic_management, etc.). NodeDB already persists the struct via
the moduleConfig protobuf save; this just wires the read path to
the phone.
2. Tag 14 — reserved gap in the oneof numbering. No payload_variant
member exists at tag 14. Without this patch, every phone reconnect
walks through config_state=14 and hits
`LOG_ERROR("Unknown module config type %d", config_state)`. On an
active deployment that's ~1,400 LOG_ERROR lines per day per node —
burying real errors. Added explicit `case 14: break;` so the gap
is silently skipped.
Also: lowered the `default:` log level from LOG_ERROR to LOG_DEBUG. A
truly-new unknown type number would indicate firmware lagging the
protobuf — annoying but not an error event worth LOG_ERROR, especially
since this path runs on every phone handshake. If a new ModuleConfig
tag appears, devs will notice via the phone UI missing it, not via log.
Observed on a Station G2 fleet: 1403 "Unknown module config type 16"
and 1427 "Unknown module config type 14" LOG_ERROR lines in 24 hours
from routine phone reconnects.
* Get rid of the placeholder
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The "Invalid protobufs (bad psk?)" and "Invalid portnum (bad psk?)"
messages fire every time a neighbor transmits on a channel whose
8-bit hash matches one of ours but the PSK differs. In RF environments
with multiple mesh groups nearby this is routine — a single device
can see dozens of these per minute from SAR/MeshCA/private networks
sharing a hash collision.
LOG_ERROR for a benign "not our PSK" event:
- spams the log when you have any neighboring mesh group
- makes a genuine PSK misconfiguration on YOUR own channel
indistinguishable from the constant cross-channel noise
- hides actual errors in the stream
LOG_DEBUG matches how similar decryption-failure paths are handled
elsewhere (eg. the PKC "decrypt attempted but failed" uses LOG_WARN).
Dropping the trailing "!" as well — these are expected events, not
exceptional ones.
The constructor sets `RadioLibInterface::instance = this` immediately,
before `init()` runs. `initLoRa()` in RadioInterface.cpp creates each
radio variant with `new SX1262Interface(...)` or similar, then calls
`init()`, and if init fails the `unique_ptr<RadioInterface>` is reset
to nullptr — destroying the object — while the static `instance`
pointer continues to point at the freed memory.
Main loop then checks `RadioLibInterface::instance != nullptr` and
calls `pollMissedIrqs()` or `resetAGC()` on the dangling pointer →
Guru Meditation (IllegalInstruction / LoadProhibited).
Reported in #9880 on an ESP32-S3 dev board without radio hardware
attached, where init always fails and the leftover pointer crashes
the device on the next `loop()` iteration.
Fix: add a virtual destructor to `RadioLibInterface` that clears the
static pointer iff it still references this object. A later successful
init() may have replaced `instance` with a different interface — the
`instance == this` guard preserves that case.
Fixes#9880
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The CALIBRATE_ALL (0x7F) command inside resetAGC() clears bit 0 of the
undocumented 0x8B5 register. That bit is set once in init() by #9571 and
#9777 to improve SX1262 RX sensitivity, and the AGC-reset path was not
re-applying it. Result: every SX1262 node silently loses the RX
sensitivity patch ~60s after boot and never recovers until reboot.
Empirically confirmed on Heltec Mesh Node T114 (nRF52840 + SX1262):
- Post-calibration read of 0x8B5 = 0x04 (bit 0 cleared)
- After re-apply: 0x05 (bit 0 set)
Reproducible every AGC_RESET_INTERVAL_MS tick.
Fix re-applies the register bit alongside the existing post-calibration
re-applies (setDio2AsRfSwitch, setRxBoostedGainMode).
* Add powerlimits to reconfigured radio settings as well as init settings.
* Refactor preamble length handling for wide LoRa configurations
* Moved the preamble setting to the main class and made the references static
The W5100S Ethernet chip has only 4 hardware sockets. On RAK4631
Ethernet gateways with syslog and NTP enabled, all 4 sockets were
permanently consumed (NTP UDP + Syslog UDP + TCP API listener + TCP
API client), leaving none for MQTT, DHCP lease renewal, or additional
TCP connections.
- NTP: Remove permanent timeClient.begin() at startup; NTPClient::update()
auto-initializes when needed. Add timeClient.end() after each query to
release the UDP socket immediately.
- Syslog: Remove socket allocation from Syslog::enable(). Open and close
the UDP socket on-demand in _sendLog() around each message send.
- MQTT: Fix socket leak in isValidConfig() where a successful test
connection was never closed (PubSubClient destructor does not call
disconnect). Add explicit pubSub->disconnect() before returning.
Made-with: Cursor
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The W5100S Ethernet chip has only 4 hardware sockets. On RAK4631
Ethernet gateways with syslog and NTP enabled, all 4 sockets were
permanently consumed (NTP UDP + Syslog UDP + TCP API listener + TCP
API client), leaving none for MQTT, DHCP lease renewal, or additional
TCP connections.
- NTP: Remove permanent timeClient.begin() at startup; NTPClient::update()
auto-initializes when needed. Add timeClient.end() after each query to
release the UDP socket immediately.
- Syslog: Remove socket allocation from Syslog::enable(). Open and close
the UDP socket on-demand in _sendLog() around each message send.
- MQTT: Fix socket leak in isValidConfig() where a successful test
connection was never closed (PubSubClient destructor does not call
disconnect). Add explicit pubSub->disconnect() before returning.
Made-with: Cursor
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix TransmitHistory to improve epoch handling
* Enable epoch handling in unit tests
* Improve comments and test handling for epoch persistence in TransmitHistory
* Add boot-relative timestamp handling and unit tests for TransmitHistory
* loadFromDisk should handle legacy entries and clean up old v1 files after migration
* Revert "loadFromDisk should handle legacy entries and clean up old v1 files after migration"
This reverts commit eb7e5c7acfa4ac077fe50980be752e4b42a739b8.
* Add NodeInfoModule integration for RTC quality changes and trigger immediate checks
* Update test conditions for RTC quality checks
* fix: apply all LoRa config changes live without rebooting
All LoRa radio settings (SF, BW, CR, frequency, power, preset,
sx126x_rx_boosted_gain) now apply immediately via reconfigure()
without requiring a node reboot.
- AdminModule: requiresReboot = false for all LoRa config changes;
LoRa changes were already handled by the configChanged observer
calling reconfigure() but the reboot flag was set unnecessarily
- AdminModule: validate LORA_24 region against radio hardware at
config time; reject with BAD_REQUEST if hardware lacks 2.4 GHz
capability (wideLora() returns false or no radio instance)
- SX126xInterface/LR11x0Interface: apply sx126x_rx_boosted_gain in
reconfigure(); register 0x08AC is writable in STDBY mode (SX1261/2
datasheet §9.6); retention registers written so setting survives
warm-sleep cycles; log warning on setter failure
- DebugRenderer: show BW/SF/CR on debug screen when custom modem is
active instead of the preset name
- DisplayFormatters: clarify comment on getModemPresetDisplayName
* fix: remove redundant reboot after LoRa config changes in on-device menus
Region, frequency slot, and radio preset pickers in MenuHandler all
called reloadConfig() then immediately set rebootAtMsec. reloadConfig()
already fires the configChanged observer which calls reconfigure(), so
the forced reboot was unnecessary — same rationale as the parent commit.
* fix: guard LORA_24 region selection against hardware capability in on-device menu
Without a reboot, reconfigure() now applies region changes directly.
Previously getRadio() caught the LORA_24-on-sub-GHz mismatch post-reboot
and reverted to UNSET — that safety net is gone. Add an explicit wideLora()
check in LoraRegionPicker so sub-GHz-only hardware silently ignores LORA_24
selection instead of attempting a live reconfigure with an invalid frequency.
---------
Co-authored-by: elwimen <elwimen@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix issue 9792, decode packet for TR test
* Fix 9792: Assure packet id decoded for TR test
* Potential fix for pull request finding
Log improvement for failure to decode packet.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* trunk fmt
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Fix issue 9792, decode packet for TR test
* Fix 9792: Assure packet id decoded for TR test
* Potential fix for pull request finding
Log improvement for failure to decode packet.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* trunk fmt
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Enhance LoRa configuration with modem presets and validation logic
* Rename bootstrapLoRaConfigFromPreset tests to validateModemConfig for clarity and consistency
* additional tidy-ups to the validateModemConfig - still fundamentally broken at this point
* Enhance region validation by adding numPresets to RegionInfo and implementing validateRegionConfig in RadioInterface
* Add validation for modem configuration in applyModemConfig
* Fix region unset handling and improve modem config validation in handleSetConfig
* Refactor LoRa configuration validation methods and introduce clamping method for invalid settings
* Update handleSetConfig to use fromOthers parameter to either correct or reject invalid settings
* Fix some of the copilot review comments for LoRa configuration validation and clamping methods; add tests for region and preset handling
* Redid the slot default checking and calculation. Should resolve the outstanding comments.
* Add bandwidth calculation for LoRa modem preset fallback in clampConfigLora
* Remove unused preset name variable in validateConfigLora and fix default frequency slot check in applyModemConfig
* update tests for region handling
* Got the synthetic colleague to add mock service for testing
* Flash savings... hopefully
* Refactor modem preset handling to use sentinel values and improve default preset retrieval
* Refactor region handling to use profile structures for modem presets and channel calculations
* added comments for clarity on parameters
* Add shadow table tests and validateConfigLora enhancements for region presets
* Add isFromUs tests for preset validation in AdminModule
* Respond to copilot github review
* address copilot comments
* address null poointers
* fix build errors
* Fix the fix, undo the silly suggestions from synthetic reviewer.
* we all float here
* Fix include path for AdminModule in test_main.cpp
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* More suggestion fixes
* admin module merge conflicts
* admin module fixes from merge hell
* fix: initialize default frequency slot and custom channel name; update LNA mode handling
* save some bytes...
* fix: simplify error logging for bandwidth checks in LoRa configuration
* Update src/mesh/MeshRadio.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Fix for preserving pki_encrypted and public_key when relaying UDP multicast packets to radio.
PKI DMs sent over UDP multicast had their pki_encrypted flag and public_key fields explicitly cleared before being forwarded to the LoRa radio. This caused the receiving node to treat the packet as a channel-encrypted message it couldn't decrypt, silently dropping it.
The MQTT ingress path correctly preserves these fields. The UDP multicast ingress path should behave the same way.
* Zeroize MeshPacket before decoding
Zeroize MeshPacket before decoding to prevent data leakage.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix for preserving pki_encrypted and public_key when relaying UDP multicast packets to radio.
PKI DMs sent over UDP multicast had their pki_encrypted flag and public_key fields explicitly cleared before being forwarded to the LoRa radio. This caused the receiving node to treat the packet as a channel-encrypted message it couldn't decrypt, silently dropping it.
The MQTT ingress path correctly preserves these fields. The UDP multicast ingress path should behave the same way.
* Zeroize MeshPacket before decoding
Zeroize MeshPacket before decoding to prevent data leakage.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix RAK4631 Ethernet gateway API connection loss after W5100S brownout
PoE power instability can brownout the W5100S while the nRF52 MCU keeps
running, causing all chip registers (MAC, IP, sockets) to revert to
defaults. The firmware had no mechanism to detect or recover from this.
Changes:
- Detect W5100S chip reset by periodically verifying MAC address register
in reconnectETH(); on mismatch, perform full hardware reset and
re-initialize Ethernet interface and services
- Add deInitApiServer() for clean API server teardown during recovery
- Add ~APIServerPort destructor to prevent memory leaks
- Switch nRF52 from EthernetServer::available() to accept() to prevent
the same connected client from being repeatedly re-reported
- Add proactive dead-connection cleanup in APIServerPort::runOnce()
- Add 15-minute TCP idle timeout to close half-open connections that
consume limited W5100S hardware sockets
Fixesmeshtastic/firmware#6970
Made-with: Cursor
* Log actual elapsed idle time instead of constant timeout value
Address Copilot review comment: log millis() - lastContactMsec to show
the real time since last client activity, rather than always logging the
TCP_IDLE_TIMEOUT_MS constant.
Made-with: Cursor
* Update src/mesh/api/ServerAPI.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Stop UDP multicast handler during W5100S brownout recovery
After a W5100S chip brownout, the udpHandler isRunning flag stays
true while the underlying socket is dead. Without calling stop(),
the subsequent start() no-ops and multicast is silently broken
after recovery.
Made-with: Cursor
* Address Copilot review: recovery flags and timeout constant
Move ethStartupComplete and ntp_renew reset to immediately after
service teardown, before Ethernet.begin(). Previously, if DHCP
failed the early return left ethStartupComplete=true, preventing
service re-initialization on subsequent retries.
Replace #define TCP_IDLE_TIMEOUT_MS with static constexpr uint32_t
for type safety and better C++ practice.
Made-with: Cursor
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix RAK4631 Ethernet gateway API connection loss after W5100S brownout
PoE power instability can brownout the W5100S while the nRF52 MCU keeps
running, causing all chip registers (MAC, IP, sockets) to revert to
defaults. The firmware had no mechanism to detect or recover from this.
Changes:
- Detect W5100S chip reset by periodically verifying MAC address register
in reconnectETH(); on mismatch, perform full hardware reset and
re-initialize Ethernet interface and services
- Add deInitApiServer() for clean API server teardown during recovery
- Add ~APIServerPort destructor to prevent memory leaks
- Switch nRF52 from EthernetServer::available() to accept() to prevent
the same connected client from being repeatedly re-reported
- Add proactive dead-connection cleanup in APIServerPort::runOnce()
- Add 15-minute TCP idle timeout to close half-open connections that
consume limited W5100S hardware sockets
Fixesmeshtastic/firmware#6970
Made-with: Cursor
* Log actual elapsed idle time instead of constant timeout value
Address Copilot review comment: log millis() - lastContactMsec to show
the real time since last client activity, rather than always logging the
TCP_IDLE_TIMEOUT_MS constant.
Made-with: Cursor
* Update src/mesh/api/ServerAPI.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Stop UDP multicast handler during W5100S brownout recovery
After a W5100S chip brownout, the udpHandler isRunning flag stays
true while the underlying socket is dead. Without calling stop(),
the subsequent start() no-ops and multicast is silently broken
after recovery.
Made-with: Cursor
* Address Copilot review: recovery flags and timeout constant
Move ethStartupComplete and ntp_renew reset to immediately after
service teardown, before Ethernet.begin(). Previously, if DHCP
failed the early return left ethStartupComplete=true, preventing
service re-initialization on subsequent retries.
Replace #define TCP_IDLE_TIMEOUT_MS with static constexpr uint32_t
for type safety and better C++ practice.
Made-with: Cursor
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Jaime RoldanandGitHub
Jennifer SanchezandGitHub
Thomas GöttgensandGitHub
Catalin PatuleaandGitHub
TomandGitHub
Kittiwut KhongkaeoandGitHub
Philip LykovandBen Meadors
WesselandBen Meadors
