* Add software LoRa IRQ polling and an MCP23017 expander HAL for radios behind an I2C expander
Some boards route the SX126x control lines (NRESET/DIO1/BUSY) through an I2C
GPIO expander instead of native GPIOs, and don't wire the expander's /INT to
the MCU, so RadioLib cannot take a hardware DIO1 interrupt.
Two reusable pieces, both gated behind USE_MCP23017 / LORA_DIO1_SOFTWARE_POLL
so builds that don't define them are unaffected:
- ExtensionIOMCP23017 + MCP23017LockingArduinoHal: a RadioLib HAL that maps
virtual pins (MCP23017_VPIN_BASE .. +15) onto an MCP23017's GPIO, so
RESET/BUSY/DIO1 reads and writes become I2C transactions while the real SPI
GPIOs (SCK/MOSI/MISO/CS) pass straight through. A failed I2C read skips the
read-modify-write rather than clobbering the rest of the bank.
- LORA_DIO1_SOFTWARE_POLL: with no DIO1 interrupt available, the SX126x
interface polls the radio IRQ status register from the radio thread and
synthesizes the ISR_TX/ISR_RX events, filtering noisy preamble/header IRQs so
they can't starve TX. A 1 ms ISR_POLL_TICK drives the poll; TX timers may
overwrite the pending tick (pollMissedIrqs() is the backup that bounds the
latency of the busy-Rx contention window). Behaviour is unchanged on all
boards that keep the hardware interrupt.
* Add Meshnology W10 AIOT Dev Kit variant (SX1262 via MCP23017 expander)
ESP32-S3R8 + EBYTE E22-900MM22S (SX1262) + AXP2101 PMIC + Quectel L76KB GPS +
SPI TFT, with the radio's RESET/DIO1/BUSY and the LCD reset routed through an
MCP23017 I2C expander at 0x20. The expander's /INT is not wired to the ESP32,
so DIO1 uses the software poll. Pins come from the board schematic and the
vendor firmware; the expander is an MCP23017 despite the V1.1 schematic's stale
'TCA9555' label (the V1.2 placement diagram and all vendor code use the MCP23017
register map).
A local pins_arduino.h shadows the generic esp32s3 variant to drop RGB_BUILTIN,
which otherwise pulls the Arduino RMT HAL into the link and fails against this
build's trimmed FreeRTOS config.
Reports HardwareModel 140 (MESHNOLOGY_W10, already present in the protobufs).
Hardware-verified on a real W10 AIOT Dev Kit: AXP2101 PMU, MCP23017, SX1262
init + a full over-the-air TX/RX round trip through the expander, PCF85063 RTC,
SHT41 and QMI8658 auto-detected, and an L76KB GPS fix.
* meshnology-w10: enable ES8311 speaker for notification tones
Bring up the ES8311 codec (I2C 0x18) -> NS4150 amp -> speaker so the board can
play notification tones / ringtones over the I2S buzzer path (the
use_i2s_as_buzzer external-notification option). Codec2 voice stays out of
scope: it is SX1280-only and this is a sub-GHz board.
- variant.h: HAS_I2S + DAC_I2S pins (MCLK=1, BCK=2, WS=4, DOUT=5, DIN=3)
- platformio.ini: arduino-audio-driver + ESP8266Audio + ESP8266SAM
- extra_variants/meshnology_w10/variant.cpp: lateInitVariant() configures the
ES8311, mirroring the other Meshtastic ES8311 boards. Kept codec-only (no
main.h) so the audio driver's 'using namespace audio_driver' does not pull a
conflicting GpioPin into scope alongside Meshtastic's class GpioPin.
- AudioThread.h: toggle the NS4150 amp (MCP23017 EXIO_PA_CTRL) around playback.
Verified on hardware: a test tune played audibly through the speaker.
* meshnology-w10: address review feedback on the MCP23017 driver
- ExtensionIOMCP23017: serialize register access with a mutex, since the radio
HAL (BUSY/DIO1/RESET) and AudioThread (amp enable) now reach the expander from
different threads and the read-modify-write paths are not atomic.
- digitalRead: return a fail-safe HIGH on a failed read instead of LOW, so a
transient I2C error on the LoRa BUSY line can't look like 'ready' and let
RadioLib start an SPI transaction early. (DIO1 is polled via the radio IRQ
register, not this pin.)
- enablePinChangeInterrupt: use the checked readReg() overload and skip on a
failed read, matching the other read-modify-write helpers.
- meshnology_w10 variant.cpp: log a warning if an ES8311 register write NACKs
instead of silently leaving the codec half-configured.
- RadioInterface.cpp: guard the MCP23017 HAL branch with ARCH_ESP32 to match the
include and driver-file guards.
* Replace board-model audio/sleep ifdefs with reusable variant capability macros
Two shared-code spots keyed off specific hardware models; move the board-specific
detail into opt-in macros the variants define, so the core code stays generic and
new boards can opt into the behavior class without touching shared files.
- AudioThread amp control: drop the T_LORA_PAGER / MESHNOLOGY_W10 ifdefs. A board
with an I2S amp now defines AUDIO_AMP_ENABLE(on) in its variant.h (T-LoRa Pager
and Meshnology W10 do), and AudioThread just calls it around playback. The
expander includes are keyed on USE_XL9555 / USE_MCP23017 (capabilities) instead
of the model name.
- Light-sleep / DIO1 wakeup: drop the SENSECAP_INDICATOR check. Boards whose
LORA_DIO1 is an expander pin (not an ESP32 GPIO) define LORA_DIO1_EXTENDED_IO
(SenseCAP Indicator and Meshnology W10), and sleep.cpp keys off that for both
the light-sleep skip and the DIO1 GPIO-wakeup skip. This also fixes a latent
issue on the SenseCAP: it previously reached the GPIO-wakeup path and called
gpio_pulldown_en() on a virtual expander pin; it now skips that cleanly.
Builds verified on meshnology_w10, tlora-pager, and seeed-sensecap-indicator.
* meshnology-w10: silence cppcheck constParameterPointer on the ISR-callback helper
isIsrTxCallback() takes a function pointer it only compares; cppcheck's
constParameterPointer wants it 'pointer to const', which is meaningless for a
function pointer (the codebase already globally suppresses the sibling
constParameterCallback). Inline-suppress it to keep the check green.
* HopScaling: qualify the member assignment as this->count
cppcheck (CI's version) flags 'count = newCount;' at the end of trimIfNeeded()
as uselessAssignmentArg ('assignment of function parameter has no effect') - a
false positive, since count is a member that outlives the call. Write it as
this->count (matching the Step-1 assignment above) so the analyzer sees a member
write. This finding comes in via the develop merge, not this board; fixing it
here to unblock the PR's cppcheck check.
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
* Add missed include
* Another Warning fix
* Add another HAS_SCREEN
* Namespace fixes
* Removed depricated destination types and re-factored destination screen
* Get rid of Arduino Strings
* Clean up after Copilot
* SixthLine Def, Screen Rename
Added Sixth Line Definition Screen Rename, and Automatic Line Adjustment
* Consistency is hard - fixed "Sixth"
* System Frame Updates
Adjusted line construction to ensure we fit maximum content per screen.
* Fix up notifications
* Add a couple more ifdef HAS_SCREEN lines
* Add screen->isOverlayBannerShowing()
* Don't forget the invert!
* Adjust Nodelist Center Divider
Adjust Nodelist Center Divider
* Fix variable casting
* Fix entryText variable as empty before update to fix validation
* Altitude is int32_t
* Update PowerTelemetry to have correct data type
* Fix cppcheck warnings (#6945)
* Fix cppcheck warnings
* Adjust logic in Power.cpp for power sensor
---------
Co-authored-by: Jason P <applewiz@mac.com>
* More pixel wrangling so things line up NodeList edition
* Adjust NodeList alignments and plumb some background padding for a possible title fix
* Better alignment for banner notifications
* Move title into drawCommonHeader; initial screen tested
* Fonts make spacing items difficult
* Improved beeping booping and other buzzer based feedback (#6947)
* Improved beeping booping and other buzzer based feedback
* audible button feedback (#6949)
* Refactor
---------
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
* Sandpapered the corners of the notification popup
* Finalize drawCommonHeader migration
* Update Title of Favorite Node Screens
* Update node metric alignment on LoRa screen
* Update the border for popups to separate it from background
* Update PaxcounterModule.cpp with CommonHeader
* Update WiFi screen with CommonHeader and related data reflow
* It was not, in fact, pointing up
* Fix build on wismeshtap
* T-deck trackball debounce
* Fix uptime on Device Focused page to actually detail
* Update Sys screen for new uptime, add label to Freq/Chan on LoRa
* Don't display DOP any longer, make Uptime consistent
* Revert Uptime change on Favorites, Apply to Device Focused
* Label the satelite number to avoid confusion
* Boop boop boop boop
* Correct GPS positioning and string consistency across strings for GPS
* Fix GPS text alignment
* Enable canned messages by default
* Don't wake screen on new nodes
* Cannedmessage list emote support added
* Fn+e emote picker for freetext screen
* Actually block CannedInput actions while display is shown
* Add selection menu to bannerOverlay
* Off by one
* Move to unified text layouts and spacing
* Still my Fav without an "e"
* Fully remove EVENT_NODEDB_UPDATED
* Simply LoRa screen
* Make some char pointers const to fix compilation on native targets
* Update drawCompassNorth to include radius
* Fix warning
* button thread cleanup
* Pull OneButton handling from PowerFSM and add MUI switch (#6973)
* Trunk
* Onebutton Menu Support
* Add temporary clock icon
* Add gps location to fsi
* Banner message state reset
* Cast to char to satisfy compiler
* Better fast handling of input during banner
* Fix warning
* Derp
* oops
* Update ref
* Wire buzzer_mode
* remove legacy string->print()
* Only init screen if one found
* Unsigned Char
* More buttonThread cleaning
* screen.cpp button handling cleanup
* The Great Event Rename of 2025
* Fix the Radiomaster
* Missed trackball type change
* Remove unused function
* Make ButtonThread an InputBroker
* Coffee hadn't kicked in yet
* Add clock icon for Navigation Bar
* Restore clock screen definition code - whoops
* ExternalNotifications now observe inputBroker
* Clock rework (#6992)
* Move Clock bits into ClockRenderer space
* Rework clock into all device navigation
* T-Watch Actually Builds Different
* Compile fix
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Add AM/PM to Digital Clock
* Flip Seconds and AM/PM on Clock Display
* Tik-tok pixels are hard
* Fix builds on Thinknode M1
* Check for GPS and don't crash
* Don't endif til the end
* Rework the OneButton thread to be much less of a mess. (#6997)
* Rework the OneButton thread to be much less of a mess. And break lots of targets temporarily
* Update src/input/ButtonThread.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* fix GPS toggle
* Send the shutdown event, not just the kbchar
* Honor the back button in a notificaiton popup
* Draw the right size box for popup with options
* Try to un-break all the things
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* 24-hour Clock Should have leading zero, but not 12-hour
* Fixup some compile errors
* Add intRoutine to ButtonThread init, to get more responsive user button back
* Add Timezone picker
* Fix Warning
* Optionally set the initial selection for the chooser popup
* Make back buttons work in canned messages
* Drop the wrapper classes
* LonPressTime now configurable
* Clock Frame can not longer be blank; just add valid time
* Back buttons everywhere!
* Key Verification confirm banner
* Make Elecrow M* top button a back button
* Add settings saves
* EInk responsiveness fixes
* Linux Input Fixes
* Add Native Trackball/Joystick support, and move UserButton to Input
* No Flight Stick Mode
* Send input event
* Add Channel Utilization to Device Focused frame
* Don't shift screens when we draw new ones
* Add showOverlayBanner arguments to no-op
* trunk
* Default Native trackball to NC
* Fix crash in simulator mode
* Add longLong button press
* Get the args right
* Adjust Bluetooth Pairing Screen to account for bottom navigation.
* Trackball everywhere, and unPhone buttons
* Remap visionmaster secondary button to TB_UP
* Kill ScanAndSelect
* trunk
* No longer need the canned messages input filter
* All Canned All the time
* Fix stm32 compile error regarding inputBroker
* Unify tft lineheights (#7033)
* Create variable line heights based upon SCREEN_HEIGHT
* Refactor textPositions into method -> getTextPositions
* Update SharedUIDisplay.h
---------
Co-authored-by: Jason P <applewiz@mac.com>
* Adjust top distance for larger displays
* Adjust icon sizes for larger displays
* Fix Paxcounter compile errors after code updates
* Pixel wrangling to make larger screens fit better
* Alert frame has precedence over banner -- for now
* Unify on ALT_BUTTON
* Align AM/PM to the digit, not the segment on larger displays
* Move some global pin defines into configuration.h
* Scaffolding for BMM150 9-axis gyro
* Alt button behavior
* Don't add the blank GPS frames without HAS_GPS
* EVENT_NODEDB_UPDATED has been retired
* Clean out LOG_WARN messages from debugging
* Add dismiss message function
* Minor buttonThread cleanup
* Add BMM150 support
* Clean up last warning from dev
* Simplify bmm150 init return logic
* Add option to reply to messages
* Add minimal menu upon selecting home screen
* Move Messages to slot 2, rename GPS to Position, move variables nearer functional usage in Screen.cpp
* Properly dismiss message
* T-Deck Trackball press is not user button
* Add select on favorite frame to launch cannedMessage DM
* Minor wording change
* Less capital letters
* Fix empty message check, time isn't reliable
* drop dead code
* Make UIRenderer a static class instead of namespace
* Fix the select on favorite
* Check if message is empty early and then 'return'
* Add kb_found, and show the option to launch freetype if appropriate
* Ignore impossible touchscreen touches
* Auto scroll fix
* Move linebreak after "from" for banners to maximize screen usage.
* Center "No messages to show" on Message frame
* Start consolidating buzzer behavior
* Fixed signed / unsigned warning
* Cast second parameter of max() to make some targets happy
* Cast kbchar to (char) to make arduino string happy
* Shorten the notice of "No messages"
* Add buzzer mode chooser
* Add regionPicker to Lora icon
* Reduce line spacing and reorder Position screen to resolve overlapping issues
* Update message titles, fix GPS icons, add Back options
* Leftover boops
* Remove chirp
* Make the region selection dismissable when a region is already set
* Add read-aloud functionality on messages w/ esp8266sam
* "Last Heard" is a better label
* tweak the beep
* 5 options
* properly tear down freetext upon cancel
* de-convelute canned messages just a bit
* Correct height of Mail icon in navigation bar
* Remove unused warning
* Consolidate time methods into TimeFormatters
* Oops
* Change LoRa Picker Cancel to Back
* Tweak selection characters on Banner
* Message render not scrolling on 5th line
* More fixes for message scrolling
* Remove the safety next on text overflow - we found that root cause
* Add pin definitions to fix compilation for obscure target
* Don't let the touchscreen send unitialized kbchar values
* Make virtual KB just a bit quicker
* No more double tap, swipe!
* Left is left, and Right is right
* Update horizontal lightning bolt design
* Move from solid to dashed separator for Message Frame
* Single emote feature fix
* Manually sort overlapping elements for now
* Freetext and clearer choices
* Fix ESP32 InkHUD builds on the unify-tft branch (#7087)
* Remove BaseUI branding
* Capitalization is fun
* Revert Meshtastic Boot Frame Changes
* Add ANZ_433 LoRa region to picker
* Update settings.json
---------
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* WIP
* ESP8266 SAM fun
* I2S audio / ext. notification module
* Remove
* Protos
* Add use_i2s_as_buzzer from protos
* Fixes
* Stuff
* Thing
* Ext. Notification working(ish)
* Remove SAM commented code
* Trunk upgrade
* Trunk
* Fixes
* Slow not fast... :-|
* T-Deck and T-Watch don't use normal buttons
* Stop ext. notification nagging with touchscreen as well
* Add button gpio back for T-Deck, but guard against long-press during ext. notification
* Ext. notification wrap up
* Better place to guard against long-press false positives
* Adjust default gain and guard against non-i2s devices referencing audio-thread
* Simplify guard logic with a boolean
* Supress uninitMemberVar
* Protos merge got out of wack
* Trunk resolution
* Remove extra crap
* Cleanup and thread-interval
* Default to alert message buzzer and add nag timeout
* Formatting
Ben MeadorsandGitHub
Thomas GöttgensandGitHub
JorropoandGitHub
Igor DanilovandGitHub
WillyJLandGitHub
Tom FifieldandGitHub
