* Add RAK WisMesh Pod variant and fix Tag LPCOMP wake on user shutdown
* chore: trunk fmt - replace Unicode em-dash in Pod comment
Co-authored-by: Cursor <cursoragent@cursor.com>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Cursor <cursoragent@cursor.com>
* fix(esp32): skip RTC timer wake on user shutdown
Do not arm esp_sleep_enable_timer_wakeup when msecToWake is portMAX_DELAY (UI shutdown), matching nRF52 system_off semantics.
fix(rak_wismesh_tap_v2): Tag OCV curve and 16MB partition
Add OCV_ARRAY matching WisMesh Tag for accurate SOC. Use 16MB flash partition scheme for TAP V2 hardware.
Co-authored-by: Cursor <cursoragent@cursor.com>
* Trunkt
* Add RAK WisMesh Repeater Mini V2 and HP variants
Introduce rak_wismesh_repeater_mini (RAK4631) and
rak_wismesh_repeater_mini_hp (RAK3401) with low-VDD System OFF.
Skip LPCOMP battery wake on user-initiated shutdown to avoid
immediate reboot near the LPCOMP threshold; keep LPCOMP for
brownout-driven shutdown via variant_enableBatteryLpcompWake.
* docs(variants): update RAK BOM numbers for Repeater Mini V2 & HP
* chore: run trunk fmt
---------
Co-authored-by: Cursor <cursoragent@cursor.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Add conditional compilation guards for LR1121 and LR2021 radio chip configurations in rfswitch.h to prevent compilation errors when these radios are not in use. Move USE_LR2021 definition to the radio section in variant.h for consistency with other radio chip definitions.
The Arduino loop task runs Meshtastic's entire cooperative OSThread
scheduler on the Adafruit core's stock 4 KB (1024-word) stack. The 2.8
first-sync path - AdminModule::handleSetConfig -> saveChanges ->
configChanged -> RadioInterface::reloadConfig -> LR11x0 reconfigure ->
SPI Lock::lock, with vsnprintf/USB-CDC logging frames stacked on top -
overflows it.
SWD fault capture on a T1000-E (pyocd vector_catch=h) proved it: the
loop task's SP was driven 40 bytes BELOW its own pxStack base, the
stack paint was consumed to the floor, and the crash was a BusFault in
xQueueSemaphoreTake dereferencing a semaphore handle that adjacent-heap
corruption had overwritten with log text (0x3f3f207c = "| ??"). The
core's HardFault handler is a bare NVIC_SystemReset, so in the field
this presents as a silent reboot ~seconds after a phone pairs (or a 30 s
zombie hang -> supervision timeout 0x8 when the corruption lands on task
TCBs instead). Also explains the set_time_only -> immediate-NodeInfo
crash variant reported on empty-DB nodes: same task, different deep
chain. 2.7.26 is unaffected because the deep frames (XEdDSA, satellite
map conversion, replay engine) did not exist.
Fix: set -DLOOP_STACK_SZ=2048 (words = 8 KB) for all nrf52840 targets.
Requires the #ifndef guard from meshtastic/Adafruit_nRF52_Arduino#7;
until that merges the flag is a harmless redefinition warning. Validated
on hardware: pairing + full sync completes, stack paint shows healthy
margin under load.
Also fix the boot-time reset-reason log: the core's init() caches
RESETREAS and W1C-clears the register before setup() runs, so the raw
read here has always printed 0. Use readResetReason() instead.
(preFSBegin's RESETREAS==0 gate is intentionally left as-is - its
degenerate GPREGRET-only behavior is what makes lfs recovery work.)
isCharging()/getHasUSB() were hard-compiled to always return false on
this board: the nrfx_power_usbstatus_get() block in Power.cpp that
derives them is gated behind #ifdef NRF_APM, and this board's variant.h
never defined it - unlike tracker-t1000-e and wio-tracker-wm1110, which
do. Confirmed on hardware: before this change, `Battery: usbPower=0,
isCharging=0` regardless of actual USB/charge state; after, `usbPower=1,
isCharging=1` while genuinely on USB power with a battery attached.
Same underlying gap as #4367, fixed for tracker-t1000-e and
wio-tracker-wm1110 in #4376 (which also fixed a deeper bug where
PowerStatus notifications were gated behind a battery-level null check -
that part is already fixed generically in Power.cpp today, so this board
only needed the define). Looks like a simple oversight from when this
board was added, since it's newer than the two boards #4376 touched.
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
Signed-off-by: Andrew Yong <me@ndoo.sg>
Every other .cpp/.h pair in src/ (350 of 351) uses identical
capitalization between the two files. Power.cpp/power.h was the sole
outlier; this aligns it with the rest of the codebase. No functional
change — all includes already resolved this file the same way on
case-sensitive filesystems.
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Right-size nRF52 heap tiers after 2.8.0 heap-exhaustion field reports
Field reports on 2.8.0 show nRF52840 devices at 99% heap (114/115 KB)
within minutes of boot; operator new asserts on OOM, so these devices
are one allocation from a reboot. The 2.8.0 cache sizing ladders gave
nRF52 the largest non-PSRAM tiers on the assumption that a BLE-only
part has a roomy heap - the arena is actually ~125 KB shared with the
FreeRTOS task stacks.
Per-target retiers (nRF52840 unless noted):
- Traffic Management cache 1000 -> 250 entries (10 KB -> 2.5 KB); the
unclassified fallthrough drops 1000 -> 400 to match the classic-ESP32
tier (also affects RP2040/RP2350)
- Warm node store 200 -> 100 entries (8 KB -> 4 KB); the non-XXAA
fallthrough drops 320 -> 100 so an unclassified RAM-constrained part
can't boot-allocate 12.8 KB
- MESSAGE_HISTORY_LIMIT 20 -> 10 (text pool 4.4 KB -> 2.2 KB), the tier
classic ESP32 already ships
- MAX_RX_TOPHONE 32 -> 16, shrinking the static packet pool 70 -> 54
slots (~6.6 KB of .bss returned to the heap arena)
- PacketHistory hash index off arch-wide (1 KB); O(n) over 240 records
is negligible at LoRa packet rates
- OLEDDISPLAY_REDUCE_MEMORY arch-wide (~1 KB OLED back buffer); the five
TFT variants -U it because TFTDisplay.cpp needs buffer_back for
dirty-window diffing
- Drop the stale "for testing" 1024-entry TMM override on T1000-E
Measured on rak4631: heap arena grows 124,572 -> 131,180 B and boot
allocations drop ~15.7 KB, roughly +22 KB free heap on the field-report
device class.
Migration: the nRF52840 warm flash ring replays through place() (LRU),
so the newest 100 identities survive the shrink; the file backend
rejects oversized snapshots cleanly (new test covers this). Native
suites pass (536/536 Docker, 13/13 native-macos warm store); rak4631,
heltec-mesh-node-t114 (TFT) and tracker-t1000-e build green.
* Add central memory-class ladder (MemClass.h) with fail-safe-small defaults
The 2.8.0 nRF52840 heap exhaustion happened because each RAM-sized cache
picked its per-platform tier from its own chip #ifdef ladder, and every
ladder's fallthrough default was its largest non-PSRAM tier - nRF52 was
never named, so it silently got 1000-entry caches on a ~115 KB arena.
This introduces src/memory/MemClass.h: a single MESHTASTIC_MEM_CLASS
(TINY / SMALL / MEDIUM / LARGE) ranked by usable app heap after platform
overheads, with the deliberate property that an unclassified chip lands
in SMALL - a new target boots with small caches until someone opts it up
in one visible place.
The TMM cache, warm store, MAX_RX_TOPHONE and MAX_SATELLITE_NODES
ladders in mesh-pb-constants.h now key off the class; branches pinned by
something other than RAM stay explicit and say why (nRF52840's SoftDevice
arena, RP2040's warm.dat watchdog bound). MAX_NUM_NODES intentionally
stays separate - it is flash-shaped (nodes.proto vs LittleFS), not
heap-shaped.
A per-class MESHTASTIC_BOOT_CACHE_BUDGET static_assert now covers the
three big boot-allocated caches, so the next cache-adding PR that would
blow a small platform's budget fails to compile instead of exhausting
heap in the field.
No values change for any existing target: rak4631, tbeam, rak11310 and
wio-e5 build byte-identical before/after; all ladders remain
#ifndef-guarded so variant overrides keep working.
* Address review: fix RP2350 class-table doc, add PacketRecord static_assert
- MemClass.h's class table claimed RP2350 was MEDIUM while the mapping
ladder classifies it SMALL (with RP2040) - the table now matches the
ladder, with a note that RP2350 is a MEDIUM candidate whenever someone
wants to tune it up (kept SMALL here so this header stays a behavioral
no-op).
- The boot-cache budget comment referenced a static_assert pinning
PacketHistory::PacketRecord at 20 B that did not exist (only a layout
comment). Add the real static_assert so the budget math in
mesh-pb-constants.h fails to compile if the record layout changes.
Also merges develop (the base #10898 landed there as a squash, which is
what made this stacked branch conflict); develop's mesh-pb-constants.h
is byte-identical to this branch's base, so the resolution keeps the
MemClass ladder unchanged. rak4631 and wio-e5 build green;
test_packet_history 47/47.
* Address review: share PACKETHISTORY_MAX, trim policy comments
- Hoist PACKETHISTORY_MAX from PacketHistory.cpp into
mesh-pb-constants.h (next to the MAX_NUM_NODES it derives from) so the
constructor clamp and the boot-cache budget static_assert use one
definition instead of hand-mirrored arithmetic that could drift. The
expression stays valid where MAX_NUM_NODES resolves at runtime
(ESP32-S3, portduino); the pointless 2.0 double math becomes integer.
- Trim the MemClass.h header (36 -> 16 comment lines) and the budget /
sizing-policy comments per the repo comment-length guideline, keeping
the class table, the fail-safe-small rule, the override mechanism, and
the include-order constraint.
rak4631 (compile-time MAX_NUM_NODES) and heltec-v3 (runtime) build
green; test_packet_history 47/47.
* Right-size nRF52 heap tiers after 2.8.0 heap-exhaustion field reports
Field reports on 2.8.0 show nRF52840 devices at 99% heap (114/115 KB)
within minutes of boot; operator new asserts on OOM, so these devices
are one allocation from a reboot. The 2.8.0 cache sizing ladders gave
nRF52 the largest non-PSRAM tiers on the assumption that a BLE-only
part has a roomy heap - the arena is actually ~125 KB shared with the
FreeRTOS task stacks.
Per-target retiers (nRF52840 unless noted):
- Traffic Management cache 1000 -> 250 entries (10 KB -> 2.5 KB); the
unclassified fallthrough drops 1000 -> 400 to match the classic-ESP32
tier (also affects RP2040/RP2350)
- Warm node store 200 -> 100 entries (8 KB -> 4 KB); the non-XXAA
fallthrough drops 320 -> 100 so an unclassified RAM-constrained part
can't boot-allocate 12.8 KB
- MESSAGE_HISTORY_LIMIT 20 -> 10 (text pool 4.4 KB -> 2.2 KB), the tier
classic ESP32 already ships
- MAX_RX_TOPHONE 32 -> 16, shrinking the static packet pool 70 -> 54
slots (~6.6 KB of .bss returned to the heap arena)
- PacketHistory hash index off arch-wide (1 KB); O(n) over 240 records
is negligible at LoRa packet rates
- OLEDDISPLAY_REDUCE_MEMORY arch-wide (~1 KB OLED back buffer); the five
TFT variants -U it because TFTDisplay.cpp needs buffer_back for
dirty-window diffing
- Drop the stale "for testing" 1024-entry TMM override on T1000-E
Measured on rak4631: heap arena grows 124,572 -> 131,180 B and boot
allocations drop ~15.7 KB, roughly +22 KB free heap on the field-report
device class.
Migration: the nRF52840 warm flash ring replays through place() (LRU),
so the newest 100 identities survive the shrink; the file backend
rejects oversized snapshots cleanly (new test covers this). Native
suites pass (536/536 Docker, 13/13 native-macos warm store); rak4631,
heltec-mesh-node-t114 (TFT) and tracker-t1000-e build green.
* Drop stale OLEDDISPLAY_REDUCE_MEMORY -U on t114 / mesh-solar-tft
Only USE_TFTDISPLAY variants (t1, t096, wismeshtap) compile
TFTDisplay.cpp and need the lib's buffer_back; t114 and mesh-solar-tft
render through the meshtastic-st7789 driver, which handles the
reduced-memory configuration fine - as #10894 (merged from develop)
already established by defining the flag there. Remove the -U guard and
the per-variant -D (redundant with the arch-wide define in nrf52_base
on this branch). Both variants verified building.
Audit of the XEdDSA packet-signing implementation (#10478) surfaced several
issues in when unsigned packets are accepted on receive or emitted on send.
This fixes them and adds regression coverage.
- Unicast NodeInfo exchange no longer breaks against signer nodes: the
NodeInfoModule downgrade drop is gated to broadcasts, since senders never
sign unicast (want_response replies, directed exchanges).
- Replace the payload-size sign heuristic with an exact encoded-size gate
(signedDataFits) and mirror it on the receive side, removing a dead band
where 167-168 B broadcasts were signed then failed TOO_LARGE.
- Extract the receive policy into checkXeddsaReceivePolicy() and apply it to
plaintext-MQTT decoded downlink, which previously skipped signature
verification and downgrade protection entirely.
- Reject signatures whose length is neither 0 nor 64 as malformed, so a
crafted partial signature can't inflate the size estimate and dodge the
unsigned-downgrade drop.
- Hold cryptLock on the MQTT verify path (shared Ed25519 key cache).
- Clear any client-preset signature on packets we originate, on all builds.
- Randomized (hedged) signing per the Signal XEdDSA spec: bump the
meshtastic/Crypto pin to the build where XEdDSA::sign mixes 32 bytes of
caller randomness into the nonce as Z (meshtastic/Crypto#3), and seed those
bytes in xeddsa_sign from HardwareRNG (checked, with a seeded-CSPRNG
fallback). test_crypto pins that repeated signs differ and both verify.
Adds test coverage: test_packet_signing groups A-E (receive matrix, send
policy, NodeInfo backstop, encoding invariants, decoded-ingress policy),
test_mqtt end-to-end downlink cases, and a test_crypto randomization check.
* Seeed Tracker X1 Support
* silence CPPCheck
* fix macro order regression and adapt stm32hal for new radiolib
* STM32 is a radiolib upstream fix ( https://github.com/jgromes/RadioLib/issues/1825 )
* fix STM32 regression
* Seeed Tracker X1 Support
* silence CPPCheck
* fix macro order regression and adapt stm32hal for new radiolib
* STM32 is a radiolib upstream fix ( https://github.com/jgromes/RadioLib/issues/1825 )
* fix STM32 regression
* address copilot OCD
* Split behavior only when the two LEDs are on distinct pins.
* bring naming in line with the other seeed devices
* update env name to fit convention too
* guarantee evaluation order
* Guard sensor readings against null values, make sensor use less power
Reconciles develop to master's latest renovate values for deps bumped on the
2.7 line but never back-merged, so the develop->master 2.8 promotion (#10777)
doesn't regress them. Done as a value reconcile, not a cherry-pick: several
master commits are superseded (5 device-ui bumps, 2 ststm32 bumps), and
develop's stale archive/refs/tags/ URL form actually blocked renovate from
bumping these (the regex expects archive/<version>.zip).
GitHub Actions:
- actions/checkout v6 -> v7 (35 refs)
- actions/cache v5 -> v6
- actions/github-script v8 -> v9 (3 refs)
- actions/stale v10.2.0 -> v10.3.0
Build / platform:
- alpine 3.23 -> 3.24 (alpine.Dockerfile)
- platformio/ststm32 19.5.0 -> 19.7.0
- platformio/nordicnrf52 10.11.0 -> 10.12.0
Libraries:
- Adafruit SSD1306 2.5.16 -> 2.5.17
- SparkFun MMC5983MA v1.1.4 -> v1.1.5
- Sensirion I2C SCD30 1.0.0 -> 1.1.1
- meshtastic esp8266-oled-ssd1306 6bfd1f1 -> 2e26010
Deliberately excluded:
- meshtastic/device-ui digest: coupled to firmware protobuf/API and develop has
diverged hard (NodeDB v25); left for a separate maintainer bump + visual check.
- libpax: develop uses the mverch67 fork (pinned by Arduino-3.x migration #9122),
master uses dbinfrago -- a fork divergence, not a version bump; not reconciled.
- platform-native digest: develop already at 61067ac (equal to master).
* NodeDB: 3-tier node store with persistent warm tier (long-tail identity retention)
Introduces a tiered NodeDB so the device retains identity (public key,
last_heard) for far more nodes than fit in the full-record hot store,
without growing heap or the persisted nodes.proto unboundedly.
- Hot store: full NodeInfoLite, MAX_NUM_NODES (120 on nRF52).
- Satellite maps: position/telemetry/environment/status capped at
MAX_SATELLITE_NODES (40 freshest); eviction via enforceSatelliteCaps /
evictSatelliteOverCap.
- Warm tier (WarmNodeStore): 40 B {num,last_heard,public_key} records for
evicted nodes so DMs to/from long-tail nodes keep encrypting/decrypting.
Persisted to /prefs/warm.dat, or on nRF52840 a dedicated 12 KB raw-flash
record-ring below LittleFS (3x4 KB pages; see linker scripts + the
nrf52_warm_region.py post-link guard).
NodeDB::getOrCreateMeshNode now demotes evicted nodes into the warm tier and
re-admits them (restoring key/last_heard). Router PKI decrypt/encode resolve
the peer key via NodeDB::copyPublicKey (hot store, then warm tier).
NodeInfoLite gains snr_q4 (sint32, Q4-encoded dB); the float snr is zeroed on
disk. NodeInfoLite grows 105 -> 112 B; backup 2432 -> 2468 B.
Note: the snr_q4 .proto change still needs to land in the protobufs submodule
(generated header is updated here; submodule pointer left at upstream).
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* NodeDB: robust receive + retention for blocked (ignored) nodes
Hardens how ignored/favourite nodes are received over admin and retained,
closing paths where a block could be lost or accidentally cleared.
- Blocking keeps the node's public key (admin set_ignored_node and
addFromContact no longer zero it / drop the warm-tier key), so a blocked
peer stays a verifiable identity.
- set_ignored_node creates the node if absent, so a block by node ID sticks
even for a node we've never heard from (e.g. pushed by a remote admin) with
no NodeInfo or key.
- Eviction protection (favourite/ignored/manually-verified) now also applies to
the load-time hot-store migration and is never undone by cleanupMeshDB, which
previously purged ignored nodes that lacked user info.
- The hot-store migration leaves our own node (index 0) in place and prefers to
demote non-protected nodes, like the runtime eviction scan.
Caps the protected set (favourite + ignored + verified) at MAX_NUM_NODES-2 via
NodeDB::setProtectedFlag(), so at least two evictable slots always remain and
getOrCreateMeshNode can always make room — replacing the previous unconditional
append that could run off the end of the node vector when every node was
protected. A locally-set favourite/ignore that hits the cap reports back to the
phone via a ClientNotification.
Adds test_nodedb_blocked covering the migration, favourite/ignored eviction
protection, ignored-survives-cleanup, and the protected-node cap. The
maintenance methods stay private in production; the test reaches them through a
PIO_UNIT_TESTING-guarded friend shim.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
# Conflicts:
# src/mesh/NodeDB.h
* fix copilot comments
* once again
* WarmNodeStore: fix cppcheck warnings (uninitvar, constVariablePointer)
Zero-initialise `stranded[]` and `seqs[]/order[]` VLAs so cppcheck can
verify there are no unguarded reads of uninitialised memory (the guards
exist but are not visible to static analysis). Mark two local pointers
`const` where the pointed-to entry is never mutated after assignment.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* self-care added to assist 2.7 and 2.8 nodedb migration
* Tidy warm-store/self-care: comments, guards, log + flash cleanup
Style/cleanup pass over the branch (no behavior change except the noted
preprocessor simplifications, which are semantically identical):
- Comments: move function descriptions to the headers, cap in-function
comments at ~3-4 lines, drop leading-number step markers, label stacked
#endif blocks, de-decorate banner comments.
- dumpToLog: fully gate decl + definition + AdminModule call site behind
MESHTASTIC_NODEDB_MIGRATION_VERBOSE so it compiles out when disabled
(~1.2 KB when off).
- mesh-pb-constants: drop the dead nRF52832 WARM_NODE_COUNT branch and trim
the macro docs.
- WarmNodeStore: simplify the redundant `ARCH_NRF52 && NRF52840_XXAA` guards
to `NRF52840_XXAA`, add a kNoPage sentinel for the ring page state.
- Shorten the always-on LOG_WARN strings (~120 B flash).
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* more tidying up, aligning with docs and undoing other-arch regressions
* Update protobufs (#19)
Co-authored-by: NomDeTom <116762865+NomDeTom@users.noreply.github.com>
* made the migration pathway cleareer
* address copilot review
* fixed a copilot review on a downstream PR.
* Address Copilot review comments for PR #10705 (warmstore/nodedb)
- WarmNodeStore.h: default MIGRATION_VERBOSE to 0 (suppress info-level
chatter on production builds; opt in with =1)
- WarmNodeStore.cpp load(): move memset to top of function so all
failure paths (header-read fail, invalid header) leave entries clear
- WarmNodeStore.cpp save(): replace manual spiLock lock/unlock around
mkdir with LockGuard covering the full SafeFile sequence, matching
the lock discipline in load()
- Router.cpp: memcpy(&p->public_key.bytes, ...) -> memcpy(p->public_key.bytes,
...) — pass decayed uint8_t* rather than pointer-to-array
- AdminModule.cpp: check setProtectedFlag return for PKC auto-favorite;
log cap-refusal warning instead of unconditional "auto-favoriting"
- nrf52_warm_region.py: error message references both v6.ld and v7.ld
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* NodeDB: formatting cleanup (blank lines after preprocessor blocks)
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* Lukewarm store
---------
Co-authored-by: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fixes
* Remove BATTERY_LPCOMP_THRESHOLD
BATTERY_LPCOMP_THRESHOLD is dead code — in main-nrf52.cpp it's inside #ifdef BATTERY_LPCOMP_INPUT, which this board intentionally doesn't define. The threshold value is never reached.
* Trunk fix
* Update MotionSensor.cpp
* fix
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Use standard GPS enable pin, for smarter power control on M3
* Enable GPS pin in variant.cpp initialization
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Test commit for XEdDSA support
* Update to Crypto lib in Meshtatic org
* Generate a new node identity on key generation (#7628)
* Generate a new node identity on key generation
* Fixes
* Fixes
* Fixes
* Messed up
* Fixes
* Update src/modules/AdminModule.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/mesh/NodeDB.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Figured it out!
* Cleanup
* Update src/mesh/NodeDB.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/mesh/NodeDB.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/AdminModule.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update crypto commit hash
* Some fixes for xeddsa pr (#9610)
* fix: add null check for getMeshNode() in NodeInfoModule
getMeshNode() can return nullptr for unknown nodes. Dereferencing
without a check crashes the firmware when receiving NodeInfo from
a node not yet in the database.
* fix: enforce XEdDSA signature verification and prevent stripping
Previously, failed signature verification still allowed the packet
through, making signatures purely cosmetic. Now:
- Failed verification drops the packet (DECODE_FAILURE)
- Successfully verified nodes get HAS_XEDDSA_SIGNED bitfield set
- Unsigned packets from previously-signing nodes are rejected
- Log levels reduced from WARN/ERROR to DEBUG/WARN as appropriate
* fix: include packet metadata in XEdDSA signature
The signature now covers [fromNode | packetId | portnum | payload]
instead of just the payload bytes. This prevents:
- Replay attacks (different packetId fails verification)
- Reattribution (different fromNode fails verification)
- Portnum redirection (different portnum fails verification)
Also adds a key initialization check to xeddsa_sign (returns false
if XEdDSA keys are all zeros) and checks the return value in the
encode path.
* fix: handle existing key pair in AdminModule security config
When a user provides both a valid private key and public key via
admin config, the crypto engine's DH private key and owner public
key were never loaded. DMs and XEdDSA signing would silently break.
Add an else branch to load both keys into the crypto engine.
* perf: cache Ed25519 public key conversion in xeddsa_verify
curve_to_ed_pub() performs field element parsing, inversion, and
multiplication on every call. Since packets from the same node
tend to arrive in bursts, a single-entry cache avoids repeating
this expensive conversion for consecutive packets from one sender.
* fix: skip identity cleanup when node number is unchanged
createNewIdentity() was called on every generateCryptoKeyPair(),
including normal boots where the same key is regenerated. This
caused unnecessary NodeDB writes and old-node cleanup logic to
run when the node number hadn't actually changed.
Also fixes only zeroing byte[0] of the old node's public key
instead of clearing the entire array.
* fix: replace hardcoded 120 with derived XEDDSA_SIGNATURE_SIZE constant
The payload size check for XEdDSA signing used a magic number (120).
Replace with a derivation from DATA_PAYLOAD_LEN and XEDDSA_SIGNATURE_SIZE
so the limit adjusts automatically if constants change. This also
increases the max signable payload from 120 to 169 bytes, which is
still safe since the actual encoded size is checked after pb_encode.
* fix: add const qualifiers to XEdDSA verify and curve_to_ed_pub inputs
pubKey, payload, and signature parameters in xeddsa_verify are
input-only and should not be modified. Same for curve_pubkey in
curve_to_ed_pub.
* chore: remove commented-out old Crypto dependency in portduino.ini
* Leave out the admin module change for now
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* trunk
* protobuf re-update
* Protobufs
* Merge resolution fix
* Put XEDDSA on the right bit
* NodeDB update to new nodeInfoLite accessors, etc
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Refine unsigned packet rejection logic in Router (#10534)
* use hardware random to fill the first 32 signature bytes with entropy prior to signing.
* Add XEdDSA packet-signing policy tests and update dependencies for macos
* Minor fixes
* integrate XEdDSA support and update dependencies across multiple modules
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Wessel <github@weebl.me>
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Add LTO support for nrf52840 while preserving interrupt handlers
* nrf52840: enable whole-image LTO on all targets via nrf52_base
Moves -flto + the nrf52_lto.py exclusion middleware from the rak4631 env
(771018ca8) up to [nrf52_base], so every nrf52840 target inherits it.
nrf52_lto.py keeps the interrupt handlers out of LTO (framework core +
TinyUSB USBD_IRQHandler) -- they're referenced only from the asm vector
table, so whole-program LTO would otherwise drop them and the chip hangs.
HW-validated: RAK4631 (SX1262, -60KB) and muzi-base (LR1121) both boot and
init their radios. Build-verified on canaryone (fresh board, base-inherited).
Caveat: the RAK "1-Watt" variant's radio does not tolerate global-LTO
(SX126x init fails); it shares the rak4631 binary, so keep that hardware on
src-only or split it into a separate target.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* nrf52840: move -fmerge-all-constants to nrf52_base (all targets)
It had been trialed on rak4631 only; it's a general image-wide flag (the
same one stm32 uses globally, ~0.7KB), so move it up to [nrf52_base] next
to -flto so every nrf52840 target gets it instead of just rak4631.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* nrf52_lto.py: normalize path separators for Windows (Copilot review)
get_abspath() returns backslash-separated paths on Windows, so the
"/FrameworkArduino/" / "/cores/nRF5/" substring matches would miss and the
ISR-owning objects would still be LTO'd -> hang on first IRQ. Replace
backslashes with forward slashes before matching. No-op on macOS/Linux.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* Fix directory handling for LTO
* Add post-link guard to check for dropped ISR handlers in nrf52 LTO
---------
Co-authored-by: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Co-authored-by: Jason P <applewiz@mac.com>
* add noise floor
* Sliding window noise floor
* Add getCurrentRSSI() to SimRadio for noise floor support
* Remove sendLocalStatsToPhone call from runOnce
* Change noise floor to int32_t type
* Use int32_t for RSSI sample storage in noise floor
* Remove float cast from noise floor assignment
* Fix Copilot review issues: fix noise floor logic, types, and null pointer
- Use robust busyTx/busyRx checks instead of simple isReceiving check
- Initialize noiseFloorSamples to NOISE_FLOOR_MIN instead of 0
- Move noise_floor assignment inside null check to prevent potential crash
- Change getNoiseFloor() and getAverageNoiseFloor() to return int32_t
- Fix RSSI validation to check for positive values (rssi > 0)
- Fix format specifier from %.1f to %d for int32_t
- Update comments to accurately reflect the sampling logic
* Fix RSSI condition to include zero value
* Change noise floor initialization to zero
* Disable noise floor for LR11x0 chips: getRSSI(bool) unsupported
* Remove updateNoiseFloor call from onNotify to avoid radio queue overflow
Per PR review feedback, calling updateNoiseFloor() in onNotify() for every
ISR event (ISR_TX, ISR_RX, TRANSMIT_DELAY_COMPLETED) can cause the LoRa
radio queue to get full. The noise floor sampling still happens in
startReceive() and after transmitting.
* fix lr11x0 current rssi
* Address noise floor review comments
* Address Copilot SimRadio noise floor comments
* Fix RadioLibInterface formatting
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* feat: add Nordic nRF54L15-DK variant (Zephyr + BLE + LoRa)
Adds a community hardware variant for the Nordic nRF54L15-DK (PCA10156)
with an external EBYTE E22-900M30S (SX1262) LoRa module. First Meshtastic
port running on the Zephyr RTOS; all other Nordic targets use the nRF5
SoftDevice stack.
Scope
-----
- New Zephyr-based platform layer under src/platform/nrf54l15/ providing
Arduino-compatible shims (Arduino.h, SPI, Wire, Print, Stream) over the
Zephyr APIs plus a LittleFS-backed InternalFileSystem on SPIM20.
- Bluetooth LE peripheral (NRF54L15Bluetooth.*) built on the Zephyr BT
host stack, exposing the Meshtastic GATT service with legacy
connectable advertising, just-works pairing, dynamic MTU exchange
(up to 247 bytes), and iOS connection-parameter tweaks.
- Variant directory variants/nrf54l15/nrf54l15dk/ with pin map for the
E22 module on connector J1, PlatformIO env (nrf54l15dk), Zephyr
DT overlay and a wiring README.
- Zephyr project config (zephyr/prj.conf + board overlay) tuned for
BT + LoRa: 16 KB main stack, 4 KB BT RX thread, RTT logging in
immediate mode, newlib-nano heap sized to leave room for the GATT
pools while still allowing ATT MTU=247.
- extra_scripts/nrf54l15_linker.py works around a PlatformIO + old Ninja
issue where Zephyr's two-pass linker script generation does not run
automatically; the post-script parses build.ninja and invokes the
gcc -E step directly before the final link.
- boards/nrf54l15dk.json board definition (PlatformIO needs it for the
DK; the Seeed platform only ships the XIAO variants).
- variants/rp2350/rp2350.ini excludes platform/nrf54l15/ from RP2350
build_src_filter so the shared platform tree does not leak between
targets.
- .gitignore: add nRF J-Link / RTT debug artifacts (flash.jlink,
rtt_*.txt).
Shared source changes
---------------------
- src/main.{cpp,h}, src/RedirectablePrint.cpp, src/FSCommon.{cpp,h},
src/mesh/{Channels,NodeDB,RadioLibInterface,MeshService,PhoneAPI}.cpp,
src/mesh/RadioLibInterface.h, src/modules/AdminModule.cpp: add small
guards / helpers so the Zephyr build compiles alongside the Arduino
targets. Behavior on existing boards is unchanged.
Hardware model
--------------
HW_VENDOR maps to meshtastic_HardwareModel_PRIVATE_HW until a dedicated
protobuf enum value is assigned upstream. The variant declares
custom_meshtastic_hw_model = 132 so the maintainers can wire the new
enum value through the protobufs repo after merge.
Hardware note
-------------
The E22-900M30S does not connect its DIO2 pin to TXEN internally — a
wire/solder bridge between DIO2 and TXEN on the module is required for
TX to work. Details and full pin map are in the variant README.
Validation
----------
Built clean against develop. On real hardware (April 2026) the port
passes end-to-end: iOS companion app pairs and connects, configuration
round-trip works, LoRa TX/RX reaches a canonical tbeam on the same mesh
channel, NodeDB updates propagate both ways, and traceroute completes.
* fix(nrf54l15): use atomic fs_rename instead of copy fallback
Zephyr LittleFS on nrf54l15 supports fs_rename natively, so route it
through the same atomic path as ESP32. The previous copyFile+remove
fallback truncated the destination before copying, leaving 0-byte files
if interrupted mid-write.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): expand storage_partition from 36KB to 700KB
LittleFS on the default 9-block (36KB) storage_partition ran out of
space during copy-on-write of config.proto, causing fs_write to return
ENOSPC and pb_encode to surface "io error" when saving configuration
via the mobile app.
Reclaim slot1_partition (the MCUboot secondary slot — unused since we
flash directly via J-Link) and grow storage_partition to span
0xb6000..0x165000 (~175 blocks).
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): drop USERPREFS_LORACONFIG_* so LoRa config stays mutable
NodeDB rewrites LoRa config from USERPREFS_LORACONFIG_* on every boot,
which prevented reconfiguration via the BLE/serial app. Drop the
variant-level defaults; users configure region and modem preset through
the app like every other variant.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): enforce MITM passkey pairing on GATT service
- Add MESH_PERM_READ/MESH_PERM_WRITE macros (READ_AUTHEN/WRITE_AUTHEN)
on all mesh service characteristics so clients must complete passkey
exchange before accessing fromNum/fromRadio/toRadio/logRadio.
- Wire FIXED_PIN mode to bt_passkey_set() so the device advertises a
known PIN (config.bluetooth.fixed_pin); RANDOM_PIN keeps default
per-pairing random passkey.
- Reduce BleDeferredThread HARD_WATCHDOG_MS from 3min to 1min.
- prj.conf: CONFIG_BT_SMP_ENFORCE_MITM=y, CONFIG_BT_FIXED_PASSKEY=y,
CONFIG_BT_SMP_SC_PAIR_ONLY=n (legacy fallback for clients that abort
SC pairing with reason 0x01 within 150ms).
* fix(nrf54l15): resolve develop-merge conflict + cppcheck warnings
The `Merge branch 'develop'` left two ~RadioLibInterface() declarations
in src/mesh/RadioLibInterface.h: the inline version added upstream by
PR #10254 (which independently applied the same UAF guard this PR was
carrying) and the out-of-line version this PR introduced. GCC rejects
the duplicate, breaking every platform build. Drop the out-of-line
declaration + definition; keep upstream's inline form.
Also silence the 13 cppcheck low warnings introduced by the new
nrf54l15 Arduino shim — Arduino's `String`/`SPISettings` API contract
relies on implicit single-arg constructors used pervasively by
existing Meshtastic code, so suppress `noExplicitConstructor` inline
with a comment instead of breaking the API. The few mechanical wins
(`const tmp[2]`, `const uint32_t *sp`) are applied directly.
* fmt: fix Trunk Check lint issues on nrf54l15-port
- extra_scripts/nrf54l15_linker.py: move regular imports above
Import("env") to silence E402, add trunk-ignore-all(F821) for the
PIO/SCons SConstruct injection (matches esp32_pre.py / nrf52_extra.py
convention)
- src/platform/nrf54l15/NRF54L15Bluetooth.cpp: clang-format 16.0.3
- boards/nrf54l15dk.json + variants/nrf54l15/nrf54l15dk/README.md:
prettier 3.8.3 (also resolves markdownlint MD060 on README tables)
No behavior change.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): address Copilot review comments + correct clang-format style
Six review threads from the 2026-04-30 Copilot review:
- src/platform/nrf54l15/nrf54l15_main.cpp: validate PSP against the nRF54L15
SRAM range (0x20000000..0x20040000) and 4-byte alignment before walking the
faulting thread's stack, and clamp the walk so it never reads past the end
of RAM. Prevents a second fault inside the fatal handler when PSP is
corrupted (common in real faults).
- src/platform/nrf54l15/nrf54l15_arduino.cpp: gate the bring-up printk traces
in digitalWrite/digitalRead (CS/NRESET toggle log, BUSY-before-NRESET
snapshot, BUSY periodic timeline) behind a new -DNRF54L15_GPIO_DEBUG flag
that is off by default. The "dev NOT READY" message stays unconditional —
it indicates a genuine hardware/DTS misconfig.
- src/modules/AdminModule.cpp: don't mutate config.device.output_gpio_enabled
from handleGetConfig(). Reflect the live pin state in the response payload
only — a getter must not write back to disk-persisted state.
- src/platform/nrf54l15/InternalFileSystem.h: derive totalBytes() from
FIXED_PARTITION_SIZE(storage_partition) at compile time so it tracks the
DK overlay's ~700 KB partition instead of the stale 36 KB hard-coded value.
Updated the file header comment accordingly.
- extra_scripts/nrf54l15_linker.py: make _extract_gcc_command() handle the
POSIX Ninja COMMAND format (no `cmd.exe /C "..."` wrapper) in addition to
the Windows form, so the script doesn't hard-fail on Linux/macOS hosts.
- src/platform/nrf54l15/NRF54L15Bluetooth.cpp: clamp NO_PIN to RANDOM_PIN
with a one-shot LOG_WARN. The mesh GATT permissions are declared with
BT_GATT_PERM_*_AUTHEN and prj.conf sets CONFIG_BT_SMP_ENFORCE_MITM=y, so
NO_PIN with no auth callbacks would leave every characteristic returning
BT_ATT_ERR_AUTHENTICATION. Falling back to RANDOM_PIN keeps the link
usable instead of silently broken. Also re-formatted this file with the
project's .trunk/configs/.clang-format (Linux braces, 4-space indent,
130-col) — the previous lint-fix commit a2aca3234 accidentally used the
default LLVM style here, which CI's clang-format would have rejected.
Build verified: pio run -e nrf54l15dk passes, RAM 47.4%, Flash 28.6%.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): address remaining Copilot review threads
Round 2/3 review fixes — bugs first, then docs/portability:
BLE concurrency (NRF54L15Bluetooth.cpp):
- onNowHasData / sendLog / BleDeferredThread / shutdown: acquire
active_conn under ble_mutex via new acquire_active_conn() helper so
disconnected_cb can't free the conn between the null check and
bt_conn_ref/bt_gatt_notify (use-after-unref).
- write_toradio: reject writes that exceed MAX_TO_FROM_RADIO_SIZE with
ATT_ERR_INVALID_ATTRIBUTE_LEN instead of returning success and silently
dropping the payload (would hide failed config writes from the phone).
- start_advertising: truncate the device name to fit the 31-byte legacy
scan-response limit and switch to BT_DATA_NAME_SHORTENED so
bt_le_adv_start() doesn't reject the payload when the name approaches
CONFIG_BT_DEVICE_NAME_MAX=32.
Linker / portability:
- main.h: drop the rp2040Loop() forward declaration that had no
definition and no callers — would surface as a link error if any RP2040
build added a call to the symbol.
- nrf54l15_arduino.cpp: transfer16() now uses static __aligned(4) DMA
buffers (matching transfer()), removing the EasyDMA-reachability hazard
of caller-stack buffers on this part.
Filesystem (InternalFileSystem.h):
- usedBytes(): return real usage from fs_statvfs() instead of 0 so OTA
/ range-test free-space guards work.
- rewindDirectory(): close the dir before reopening — Zephyr fs_dir_t has
no rewind, and re-fs_opendir on an open handle leaks LittleFS state.
Crash handler (nrf54l15_main.cpp):
- After the stack walk, busy-wait 50 ms to flush RTT/printk and call
sys_reboot(SYS_REBOOT_COLD) directly so the saved_crash record is
actually reported on the next boot. Default Zephyr config has
RESET_ON_FATAL_ERROR=n, so the previous k_fatal_halt() spun forever.
Generalization / config:
- PhoneAPI.cpp: replace the NRF54L15_DK ifdef with a
MESHTASTIC_EXCLUDE_FILES_MANIFEST capability flag (defined in the
nrf54l15dk env) so future variants can opt in/out without touching
shared code.
- variants/nrf54l15/nrf54l15.ini: parameterize libdeps include paths via
${PIOENV} so additional nRF54L15 envs sharing nrf54l15_base don't break.
- prj.conf: drop the stale "36 KB storage_partition" comments — the DK
overlay reclaims slot1 to ~700 KB and runtime size comes from
FIXED_PARTITION_SIZE.
- nrf54l15dk overlay: remove the zephyr,console / zephyr,shell-uart
chosen entries that conflicted with CONFIG_UART_CONSOLE=n + RTT
console; keep uart30 enabled so swapping the console is one Kconfig
flip away.
Build: nrf54l15dk SUCCESS (flash 28.6%, RAM 47.4%); wiznet_5500_evb_pico2
SUCCESS (verifies the shared main.h change).
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15dk): use PRIVATE_HW (255) for custom_meshtastic_hw_model
Per @thebentern's review: the nRF54L15-DK is a development kit, not a
canonical Meshtastic SKU, so it falls under HardwareModel::PRIVATE_HW
(255) — the same enum value already used at runtime via HW_VENDOR. The
placeholder 132 is removed; no dedicated enum number will be assigned
for DK boards. Slug stays NRF54L15_DK as a human-readable identifier.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): unstarve bt_long_wq so SC pairing completes
bt_pub_key_gen() runs the ECC P256 key generation on bt_long_wq. At default
prio=10 (preemptible) and stack=1400 it gets starved by Meshtastic app
threads at boot — sc_public_key stays NULL for minutes, smp_public_key()
defers with SMP_FLAG_PKEY_SEND, and every SC pairing attempt stalls right
after the public-key exchange. iOS shows "Connecting…" forever with no
PIN prompt; bleak/CLI fails the first CCC notify write with
"Protocol Error 0x05: Insufficient Authentication".
Set CONFIG_BT_LONG_WQ_PRIO=0 (highest preemptible, ties with main) and
CONFIG_BT_LONG_WQ_STACK_SIZE=4096 (margin for the P256M driver frames).
Validated E2E with iOS Meshtastic app: bt_smp_pkey_ready fires within ~40 s
of boot, 20 SC Passkey Entry rounds complete with matching pcnf/cfm,
encrypt 0x01 / sec_level 0x04 (Authenticated MITM), bonded=1.
* feat(nrf54l15): hardware I2C bus via TWIM30 + sensor telemetry
Adds the Arduino TwoWire layer for the nRF54L15-DK so Meshtastic's
sensor drivers can talk to external I2C devices over the hardware
TWIM30 peripheral.
Bus binding:
- &uart30 disabled in the board overlay (peripheral instance 30 is
shared between UARTE30 / TWIM30 / SPIM30 — pick one). Console stays
on RTT via CONFIG_RTT_CONSOLE.
- New i2c30_default / i2c30_sleep pinctrl with SDA=P0.03 / SCL=P0.04.
External 4.7 kOhm pull-ups required on both lines.
- &i2c30 enabled at I2C_BITRATE_FAST (400 kHz).
- button_3 (SW3, P0.04) deleted from DTS so the pad can be claimed by
i2c30 pinctrl; SW3 is still wired to the pad on the DK, do not press
it during I2C use or it will short SCL to GND.
Arduino layer:
- src/platform/nrf54l15/Wire.cpp resolves the DT node at compile time
via DEVICE_DT_GET(DT_NODELABEL(i2c30)) and dispatches Arduino's
beginTransmission / write / endTransmission / requestFrom to
i2c_write / i2c_write_read / i2c_read. Buffer is sized to 256 bytes
for forward compatibility with the SE050 secure element on the
custom PCB.
- Wire.h drops the prior compile-only stubs and exposes the real
TwoWire surface.
- Arduino.h: BitOrder becomes an enum (not #define) so Adafruit_BusIO's
`typedef BitOrder BusIOBitOrder;` compiles.
Variant + build flags:
- nrf54l15.ini flips HAS_WIRE / HAS_SENSOR / HAS_TELEMETRY from 0 to 1
and cherry-picks the sensor libs Meshtastic needs (BusIO, Sensor,
BMP280, BME280, INA219/226/260/3221, SHT4X). The full
environmental_base group is avoided because it pulls
Adafruit_SSD1306 / Adafruit_GFX which rely on Arduino pin macros the
Zephyr shim does not implement.
- nrf54l15dk variant.h defines PIN_WIRE_SDA / PIN_WIRE_SCL for parity
with the Arduino convention used by other variants. The actual bus
wiring is fixed by the overlay pinctrl above.
Validated 2026-05-14/15 on the DK with BMP280 @ 0x76 (temperature +
barometric pressure) and INA3221 @ 0x42 (rail voltage / current);
EnvironmentTelemetry / PowerTelemetry packets transmit successfully
over LoRa.
Footprint cost on nrf54l15dk: +45 KB flash, +1.7 KB RAM.
* feat(nodedb): honor USERPREFS for environment telemetry on first boot
installDefaultConfig() now respects two new compile-time prefs:
USERPREFS_CONFIG_ENV_TELEM_UPDATE_INTERVAL
USERPREFS_CONFIG_ENVIRONMENT_MEASUREMENT_ENABLED
The mobile apps enforce a 30 min floor on environment_update_interval
in the settings UI, which makes short-interval bring-up testing of new
sensor hardware painful — you have to wait half an hour for the first
LoRa packet to confirm wiring + driver. With these prefs baked into
the variant, the firmware can ship a freshly-flashed device that
broadcasts on a shorter cadence (e.g. 900 s) the moment storage_partition
is empty.
Both prefs are gated on #ifdef so the behavior is unchanged for any
variant that does not opt in. Documented in userPrefs.jsonc with the
existing telemetry-interval pref block.
* fix(nrf54l15): allow multiple bonded BLE peers
CONFIG_BT_MAX_PAIRED defaults to 1, so once the first peer (e.g. an
iOS phone) has paired and bonded, every subsequent pairing attempt
from a different MAC fails inside bt_keys_get_addr() with no free
key slot — the host returns BT_SECURITY_ERR_KEY_DOES_NOT_EXIST and
the second peer never gets past SMP.
Raise the slot count to 4 so the device can simultaneously hold an
iOS phone, a Windows host, a Linux host, and one spare bond. Add
BT_KEYS_OVERWRITE_OLDEST so that once the table fills, the LRU peer
is evicted on the next pairing rather than rejecting the new peer.
This matches the behavior other Meshtastic ports already provide
(nRF52 uses CONFIG_BT_PERIPHERAL_PRIO_CONN with similar semantics).
Discovered while bringing up the Python CLI on Windows alongside
the existing iOS bond.
* fix(nrf54l15): zero-initialize TwoWire buffers + clang-format Wire
cppcheck on every CI target (esp32s3, rp2040, rp2350, nrf52840, ...) was
failing the build with two `uninitMemberVar` warnings on TwoWire's
constructor: `txBuf` and `rxBuf` (256-byte arrays) were not initialized.
Even though the buffers are only read after txLen/rxLen is set, leaving
them uninitialized is a footgun if any future caller bypasses the
len-set step. Use C++11 value-initialization in the member initializer
list — costs ~512 B of memset at boot, gains a clean cppcheck pass and
defensive-against-future-changes semantics.
Also reformat Wire.{cpp,h} with the project's `.trunk/configs/.clang-format`
config so the Trunk Check Runner passes — clang-format moved the
`<errno.h>` include before the Zephyr-namespaced ones in Wire.cpp and
collapsed two inline overloads to single lines in Wire.h.
* fix(AdminModule): remove dead OUTPUT_GPIO_PIN/GpioOutputModule references
OUTPUT_GPIO_PIN is never defined and modules/GpioOutputModule.h doesn't
exist in the codebase; all #ifdef OUTPUT_GPIO_PIN branches were dead code
introduced by the nRF54L15-DK variant commit. Strips the include, the
output_gpio_enabled OFF→ON/ON→OFF transition logic in handleSetConfig(),
and the digitalRead() reflection in handleGetConfig().
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* LR2021 radio on NRF_Promicro
Co-authored-by: Copilot <copilot@github.com>
* Refactor LR2021 interface includes and conditional compilation for improved clarity
Co-authored-by: Copilot <copilot@github.com>
* Refactor LR20x0 interface: remove unused includes and update comments for clarity
* Fix LR2021 max power definitions and add radio type detection tests
* remove potato radio type detection tests
* Include placeholder for DCDC - currently requires godmode
* Added godmode features - not enabled by default
---------
Co-authored-by: Copilot <copilot@github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* dependency swap - INA3221Sensor
update INA3221 initialization and measurement methods for compatibility with Rob Tillaart's library
Co-authored-by: Copilot <copilot@github.com>
* Addresses copilot review
Co-authored-by: Copilot <copilot@github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Refine comments on USB detection and INA3221
Updated comments regarding USB detection and INA3221 usage.
* Fix static_assert conditions for INA3221 channel definitions
Co-authored-by: Copilot <copilot@github.com>
* moved macro defines earlier to allow better use.
Co-authored-by: Copilot <copilot@github.com>
* Add raw register read methods for bus voltage and shunt current in INA3221Sensor
Co-authored-by: Copilot <copilot@github.com>
---------
Co-authored-by: Copilot <copilot@github.com>
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* True Colors on TFT (Heltec Mesh Node T114, Heltec Vision Master T190, CardPuter Adv, T-Deck, T-Lora Pager)
* Theme support - New and some Classic Themes!
* Colored Compass
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
kevin
Thomas GöttgensandGitHub
IrisandGitHub
Andrew YongandGitHub
HarukiToredaandGitHub
TomandGitHub
Jonathan BennettandGitHub
AustinandBen Meadors
Quency-DandGitHub
Benjamin FaershteinandGitHub
