ae16c052d5e12ec6e736d9216cb5be10b7da67f9
7
Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
  Ben MeadorsandGitHub
|
ae16c052d5 |
Time out an abandoned admin edit transaction (#11254)
begin_edit_settings sets a bool that only the matching commit ever clears. If the commit never arrives -- the client dropped its link partway through a bulk config import, or went away entirely -- the transaction stays open indefinitely, and every later config write from any client is applied to RAM, acknowledged, and then never saved. The writes look successful and are visible in get_config, but the node reverts all of them at the next boot, and only a reboot clears it. Give the transaction a one minute idle timeout. Each deferred write restarts the clock, so the window bounds the gap between writes rather than the length of the edit; a bulk import sends them milliseconds apart. The next admin message after it lapses retires the transaction, persisting the segments it had deferred and flushing the warnings it was holding. The check runs after the auth gates and before the switch, so every case sees consistent state and the recovery's flash write happens in the main loop rather than a disconnect callback. It saves rather than rolls back because there is nothing to roll back to: each write already took effect in RAM and was acknowledged, so the transaction only ever deferred the save. That also makes an early expiry cheap -- the worst case for a client that really was still going is that its remaining writes are saved individually instead of batched. Closing on disconnect instead was tempting, but the reporter's captures show iOS dropping and reconnecting within half a second several times per session, which would abort imports that currently survive the blip. Also drops the file-scope hasOpenEditTransaction, shadowed by the class member at every use site and referenced nowhere else in the tree. Reported in #11245 |
||
 
|
1e982fa78c |
Sign plaintext packets in licensed mode (#10969)
* feat: sign licensed plaintext packets Preserve and publish identity keys in licensed mode so existing XEdDSA signatures can authenticate plaintext traffic. Sign licensed broadcasts and direct messages when they fit, while keeping PKI encryption disabled and normal routing behavior unchanged. * fix(security): persist licensed channel sanitation * fix(security): close licensed migration lifecycle gaps * fix(security): address licensed signing review feedback * test: restore signing globals from Unity teardown * fix(baseui): allow confirmed ham region selection * fix(baseui): guard region picker validation * style: trunk fmt --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com> Co-authored-by: Austin <vidplace7@gmail.com> |
||
 Thomas GöttgensandGitHub
|
6f522aad17 |
Return the secret sentinel for remote admin config gets (#11093)
writeSecret is a setter, so calling it on the NETWORK_CONFIG get path was a no-op: the buffer already holds the stored psk, never the sentinel. MQTT_CONFIG returned the broker password verbatim. Both get paths now return secretReserved when req.from != 0, and the matching set paths call writeSecret so a read-modify-write round trip keeps the stored value. |
||
|
Thomas GöttgensandGitHub
|
8147970957 |
AdminModule: only accept admin responses to requests we sent (#11024)
* AdminModule: only accept admin responses to requests we sent An admin *_response short-circuited the auth and session-passkey checks that gate every other admin message, so any node could deliver one. On a channel the module listens to unauthenticated, a get_module_config_response drives the remote-hardware pin handler with attacker-supplied values. Track the destination of outgoing admin requests (per remote, with the pinned PKC key when there is one) and accept a response only from a node with a matching outstanding request, inside the same window as the session passkey. Local (from == 0) admin is unchanged; PhoneAPI already gates it. Also fix the response dispatch: get_module_config_response.which_payload_variant is a ModuleConfig oneof tag, but it was compared against the AdminMessage ModuleConfigType enum (different numbering), so the handler never ran. Compare against the oneof tag. * AdminModule: rollover-safe request window, bind response to request type Two review refinements to the request/response pairing: Use Throttle::isWithinTimespanMs for the outstanding-request expiry instead of comparing millis()/1000 sums, which mis-expired across the millis() rollover. Bind each accepted response to a request type actually sent to that node. Each outstanding record now carries a bitmask of the response variants its requests authorize, so a get_owner request no longer admits a get_module_config response. The mask accumulates per remote, so a client may still pipeline several request types to one node and have every answer accepted. * AdminModule: track admin requests per-request, not per-node Reworks the outstanding-request table so each request is its own entry with its own expiry window and pinned key, replacing the per-node bitmask that shared one timestamp and one key across every response variant. That sharing let a later request to the same node extend an earlier one's window and, worse, clear its PKC pin: an unpinned request cleared keyValid, so a plaintext response to an earlier PKC-pinned request was then accepted. Per-request entries keep each pin intact. Identical requests are de-duplicated (a client may fetch several config subtypes, all answered by one response variant) and eviction compares elapsed time, which is rollover-safe. Test: a pinned request's response still requires its key after an unpinned request to the same node. * AdminModule: match module-config subtype and consume answered requests Two refinements to the request/response pairing: Only remote_hardware get_module_config_response mutates state (the pin table), so it must answer a request for that exact ModuleConfigType, not just any module-config request. Each entry records the requested subtype and the gate checks it. A matched request is now consumed on accept, so a node cannot replay a state-mutating response within the window. Because one request yields one response, request de-dup is dropped (a client's N indexed get_channel requests are N entries, each consumed once). Tests: a non-remote-hardware request does not admit a remote_hardware response, and a second copy of an answered response is rejected. |
||
|
Thomas GöttgensandGitHub
|
d3d02af817 |
AdminModule: don't return the device private key to remote config reads (#11030)
A SECURITY_CONFIG get_config response copied config.security verbatim, so a remote request was answered with the device identity private_key and sent over the air. Only the local owner needs it, for backup. Zero private_key in the SECURITY_CONFIG response when the request is remote (from != 0); the local BLE/USB/TCP path (from == 0) still receives it. public_key and admin_key are public and stay as they were. |
||
 
|
952c825167 |
Allow key verification to work for unknown nodes. (#10669)
* Allow key verification to work for unknown nodes. * trunk * More reliable admin key decryption * Add admin key fallback tests * Actually check haveRemoteKey * Logging cleanup * Address review feedback - Persist the committed key + manually-verified flag in commitVerifiedRemoteNode via saveToDisk(SEGMENT_NODEDATABASE), replacing the "todo: initiate save" - Guard the CryptoEngine pending-key slot with a dedicated internal lock; the Router reads it while already holding the non-recursive cryptLock, so the accessors cannot reuse that lock - Draw the security number from the hardware RNG (CryptRNG fallback) under cryptLock instead of random(); on nRF52 the entropy fill toggles the same CC310 the BLE task's packet crypto uses - Return true after fully handling the hash2 response (restores develop behavior; consistent with the hash1 branch) - Take uint32_t in the number-picker callbacks so 8-digit hex nodenums can't truncate through int - Trim over-long comments flagged by review * feat(tests): add deterministic tests for admin session-key behavior --------- Co-authored-by: Claude Opus 4.8 (1M context) <noreply@anthropic.com> Co-authored-by: Ben Meadors <benmmeadors@gmail.com> |
||
|
d846780a9b |
More fuzz tests and small fixes for the findings (#10864)
* first pass tests * more tests * Fix two crafted-admin-packet crashes found by the E5 fuzzer Both are reachable from an authorized admin (local from==0, admin channel, or PKC) - remote DoS: 1. SIGFPE in LoRa config validation. A set_config LoRaConfig with use_preset=false and bandwidth=0 makes freqSlotWidth 0, so numFreqSlots is 0 and `hash(name) % numFreqSlots` (RadioInterface.cpp) divides by zero. Guard the modulo; the existing channel_num check then rejects/ clamps the config. 2. Stack overflow in Channels::getKey. A SECONDARY channel at the primary slot with an empty PSK recursed into getKey(primaryIndex) forever. Skip the primary-key borrow when chIndex == primaryIndex. Re-enable the E5 admin fuzzer to hit both triggers again (use_preset both ways incl. bandwidth 0, plus the set_channel tag) as regression guards. Co-Authored-By: Claude Fable 5 <noreply@anthropic.com> * Correct fuzz-test invariants after the crash fixes - E5 admin fuzz: node eviction under a filling NodeDB is legitimate, so assert only the bounded-count invariant, not that a specific seed node survives 6000 mutating ops. - TMM blitz: scope off the nodeinfo direct-response send path (it needs a fully-wired MeshService/phone queue the fixture doesn't provide; the deterministic directResponse tests cover it). The crafted-nodenum rate/unknown/position cache stress is unchanged. clod helped too * realistic tests * test: dedup fuzz RNG into shared test/support/DeterministicRng.h The four in-tree fuzz suites (test_fuzz_decode, test_fuzz_packets, test_hop_scaling, test_traffic_management) each carried a byte-identical copy of the seeded 64-bit LCG (rngSeed/rngNext/rngByte/rngRange). Hoist it into one shared header so there is a single generator to reason about and no risk of the copies drifting. static inline keeps per-suite state per translation unit and avoids -Wunused-function for suites that don't use every helper. Also corrects a stale comment in test_traffic_management (the blitz's nodeinfo direct-response path is intentionally left off). No behavioral change: same constants, same per-suite seeds. clod helped too * test: fuzz uncovered ProtobufModule handlers and the MQTT downlink ingress Extend the in-tree fuzz coverage to packet sources that previously had none: - test_fuzz_packets E8/E9/E10: drive PositionModule, DeviceTelemetryModule and NeighborInfoModule at handleReceivedProtobuf directly (via using-shims, bypassing the ProtobufModule reply/send path so no router is needed). The fixture already stands up nodeDB/service/channels, and nodeStatus/powerStatus are auto-initialized in main.cpp, so no new globals are required. Adds a shared fuzzRxHeader() helper for crafting adversarial RX packet headers. - test_fuzz_decode: add meshtastic_KeyVerification to the decode table. The KeyVerification and StoreForward handler paths are documented as decode-level only, with the concrete reason each is intrinsic (private-state gating / PSRAM + self-pointer wiring), not a fixture gap. - test_mqtt: test_receiveFuzzServiceEnvelope blitzes the non-RF broker-push ingress (onReceiveProto) two ways - raw garbage bytes that must fail envelope decode cleanly, and a well-formed ServiceEnvelope wrapping a crafted inner MeshPacket over crafted channel_id/gateway_id - exercising the channel match, isFromUs, XEdDSA receive policy and perhapsDecode chain. Adds a deliverRaw() passthrough to MQTTUnitTest. All under the coverage env (ASan/LSan). No firmware/src changes. Full sweep GREEN 27/27, 544 cases. clod helped too * Harden LoRa/channel config against crafted admin messages; consolidate test helpers Production (review findings on the hot-fuzz crash fixes): - Clamp bandwidth at the source (clampBandwidthKHz) in checkOrClampConfigLora and applyModemConfig so numFreqSlots can never be 0 for any consumer; a bandwidth-0 set_config previously passed validation and re-armed the SIGFPE on the next applyModemConfig. - Guard applyModemConfig's hash % numFreqSlots (the validator's sibling modulo was fixed earlier but this one was still unguarded). - Enforce the primary-channel invariant in Channels::onConfigChanged: a config demoting every slot now re-promotes the stale SECONDARY slot (keeping its key) or restores the default channel if the slot is DISABLED, instead of leaving every getPrimaryIndex() reader on a non-primary slot. The getKey recursion guard stays as defense-in-depth. Tests: - New test/support/MockMeshService.h and AdminModuleTestShim.h replace four byte-identical mocks and three divergent admin shims (test_mqtt's capturing mock is genuinely different and stays). - DeterministicRng.h: add rngFill() (replaces 14 hand-rolled fill loops) and rngEdgeNodeNum() (unifies the three NodeNum boundary pools). - Extract fuzzChannelSettings() shared by the set_channel case and fuzzBeacon. - fuzzBeacon: the un-terminated branch now fills the whole buffer with non-NUL bytes so the strnlen bound is actually stressed (~50% of iterations, not ~4%). - E6 beacon fuzz: replace the TEST_ASSERT_TRUE(true) tautology with real invariants (handler never consumes; offers land in lastReceivedOffer keyed to the sender). - Trim the seven over-long comment blocks flagged against the 1-2 line rule; the FINDINGS trailer moves to this commit message (see production notes). Full native suite GREEN 27/27 under the coverage (ASan/LSan) env. Co-Authored-By: Claude Fable 5 <noreply@anthropic.com> * Clamp UTF-8 char length in the emote walkers; add test_fuzz_emotes A TEXT_MESSAGE payload is opaque protobuf bytes, so PB_VALIDATE_UTF8 never screens it - invalid UTF-8 and truncated multi-byte lead bytes reach the emote/width render path verbatim. EmoteRenderer's walkers advanced by utf8CharLen(lead) without clamping to the bytes actually remaining, so a truncated lead (e.g. a lone 0xF0, which claims 4 bytes) near the end of the buffer made getUtf8ChunkWidth's memcpy read past the string. ASan confirms a heap-buffer-overflow READ from measureStringWithEmotes. Add utf8CharLenClamped() and use it at every walk site (width measure, truncation cut-loop, and the draw-path text-run/chunk builders); the one already-guarded site (matchAtIgnoringModifiers) is unchanged. New test/test_fuzz_emotes drives measureStringWithEmotes and truncateToWidth over adversarial byte strings (biased to embed/end in truncated multi-byte leads) in exact-sized heap buffers so any over-read is a hard ASan fault. Its headless display uses a synthetic font (firstChar 0, fontData centered in a large buffer) so the stock OLEDDisplay::getStringWidth - which indexes the font jump table with a signed char and over-reads for any byte >= 0x80 - does not mask the finding. native-suite-count bumped 27 -> 28. Full native suite GREEN 28/28 under the coverage (ASan/LSan) env. Co-Authored-By: Claude Fable 5 <noreply@anthropic.com> * Keep emote width measurement in-bounds for non-ASCII bytes OLEDDisplay::getStringWidth (the utf8=false path EmoteRenderer uses on default builds) indexes the font jump table by (c - firstChar) with a signed char and no bounds check, so any byte outside printable ASCII - high bytes from UTF-8 text, but also a stray control byte like 0x0A - reads outside the font array. On-device this reads adjacent flash and returns a garbage width; under ASan the test_fuzz_emotes fuzzer flags it as a global-buffer-overflow, and it made the non-ASCII width measurement meaningless either way. The OLED driver is a pinned upstream dependency, so guard it firmware-side in EmoteRenderer's getStringWidth helper: measure a sanitized copy where any byte outside [0x20, 0x7E] counts as a '?' placeholder. Printable ASCII is unchanged and the UA/RU lookup path is untouched. test_fuzz_emotes now drives a real ArialMT font instead of the synthetic in-bounds font it needed before this fix, so the suite exercises the true production width path (utf8CharLen clamp + this sanitizer) end to end. The same fuzzer tripped the global-buffer-overflow before this change. Full native suite GREEN 28/28 under the coverage (ASan/LSan) env. Co-Authored-By: Claude Fable 5 <noreply@anthropic.com> --------- Co-authored-by: Claude Fable 5 <noreply@anthropic.com> |