* add watchdog to rp2xx0
* feat(eth-api): phase 0 skeleton — HTTP API server on TCP/80 (503 only)
First step of porting mesh/http/ to RP2350 + W5500 (today ESP32-only).
Phase 0 stands up the listener over the existing arduino-libraries/Ethernet
stack (no Mongoose — its built-in TCP/IP would conflict with EthernetServer
and break OTA/MQTT/NTP). Skeleton parses request line, logs it, replies 503.
Real handlers (/api/v1/{info,fromradio,toradio}) come in later phases.
- New mesh/eth/ethApiServer.{h,cpp} gated by HAS_ETHERNET_API
- Wired into ethClient init+loop in parallel with existing ethHttpOTA (port 4244)
- Enabled in both wiznet_5500_evb_pico2_e22p and pico2_w5500_e22 variants
- Build impact on wiznet: +~9 KB flash (63.0% used), <1 KB RAM
* feat(eth-api): phase 1 — implement /api/v1/{fromradio,toradio} with PhoneAPI
Replace phase 0 skeleton with the real handlers that bridge the HTTP transport
to PhoneAPI, mirroring mesh/http/ContentHandler (ESP32) semantics.
- EthHttpAPI : public PhoneAPI (api_type=TYPE_HTTP, checkIsConnected=true),
outside the MESHTASTIC_EXCLUDE_WEBSERVER gate so it builds on RP2350.
- Minimal HTTP parser: method/path/query/Content-Length, no allocations beyond
Arduino String, capped at 32 header lines x 256 bytes (anti-DoS).
- OPTIONS preflight -> 204 with CORS + X-Protobuf-Schema.
- GET /api/v1/fromradio[?all=true]: stream-write up to 64 protobufs from
webAPI.getFromRadio(), Connection: close framing (HTTP/1.0 style).
- PUT /api/v1/toradio: read Content-Length bytes (<=512), call
webAPI.handleToRadio(), echo body back.
- 404 default for unknown paths, 405 for wrong method, 400 for bad body.
Validated e2e against wiznet @ 192.168.1.143:
- OPTIONS /api/v1/fromradio -> 204 + correct CORS headers
- PUT ToRadio{want_config_id=1} (2 bytes) -> 200 + echo
- GET /api/v1/fromradio?all=true -> 200 + 3476 bytes (config+channels+nodeinfo)
- GET /api/v1/nonexistent -> 404 unknown endpoint
- OTA HTTP on port 4244 untouched and still responsive
Build impact on wiznet_5500_evb_pico2_e22p: +2 KB flash (63.1%), +1.8 KB RAM
(17.6%) vs phase 0.
* fix(eth-api): move accept loop to dedicated OSThread (20ms tick)
The API server was being polled from the Ethernet client Periodic which runs
every 5s. Measured impact before this fix on wiznet @ 192.168.1.143:
req 1: ttfb=6.458s total=6.509s (matches the 5s tick + handler overhead)
req 2: connection refused (W5500 sockets exhausted)
req 3: connection refused
After: same hardware, same network, back-to-back requests:
req 2: ttfb=0.287s
req 3: ttfb=0.015s
req 4: ttfb=0.022s
req 5: ttfb=0.020s
The web client (meshtastic/web served from localhost) was visibly stalling
mid-handshake — it had pulled 109 nodes + 19 messages but channels and device
info never arrived. With the periodic-only polling, every request takes 5s
and the W5500's 4 hardware sockets fill up under the burst.
EthApiServerThread mirrors the WebServerThread pattern from ESP32
mesh/http/WebServer.cpp: adaptive interval — 20ms when there's recent
traffic, 100ms after 5s of idle, 500ms after 30s. Auto-registers with the
OSThread scheduler on construction.
ethHttpOTA still ticks from the periodic; left unchanged because OTA is one
large transfer that tolerates the latency, and minimizing scope here to one
behaviour change at a time.
* refactor(eth-api): extract handlers to shared module via IStreamReadWrite
Phase 2.0 of the TLS port — separate transport from request handling so
the upcoming HTTPS server can reuse the exact same parser + routing logic.
- New ethApiHandlers.{h,cpp}: Request, parser, CORS helpers, fromradio/toradio
handlers, EthHttpAPI : PhoneAPI subclass. All driven by a single
IStreamReadWrite interface that inherits Print (so client.print(...) keeps
working transparently).
- ethApiServer.cpp slimmed to ~90 LOC: now just the EthernetServer(80) +
OSThread + an EthernetClientStream adapter that forwards reads/writes to
the underlying EthernetClient. No behaviour change.
Validated on wiznet @ 192.168.1.143: 5 curl requests TTFB 18-110ms (same
as pre-refactor), protobuf round-trip PUT 200 + GET ?all=true 3499 bytes.
Flash impact: +200 bytes (63.2%); RAM unchanged (17.6%).
* feat(eth-tls): ECDSA P-256 self-signed cert generation for HTTPS API
mbedTLS-based cert generation module that produces a SAN=IP self-signed
ECDSA P-256 server certificate, persisted under LittleFS so subsequent
boots reuse the same key. Generation runs once on a dedicated OSThread
so the ECDSA keygen path (~430 ms) never blocks the Periodic stack or
the Ethernet reconnect loop.
- mbedTLS 3.6.2 sources compiled in via scripts/add_mbedtls_sources.py
(BuildSources of pico-sdk/lib/mbedtls/library/*.c, all 108 files).
MBEDTLS_USER_CONFIG_FILE injected as CPPDEFINES tuple in the script —
build_flags shell escape mangles the embedded quotes on Windows.
- src/mbedtls_user_config.h undefs MBEDTLS_HAVE_TIME, HAVE_TIME_DATE,
TIMING_C, NET_C, FS_IO, PSA_ITS_FILE_C, PSA_CRYPTO_STORAGE_C, and
defines MBEDTLS_NO_PLATFORM_ENTROPY (entropy_poll.c uses a raw
platform check, not gated by a flag).
- src/mesh/eth/ethCert.{h,cpp}: ECDSA P-256 keypair + cert with
SAN(IP=current) using pico-sdk get_rand_64() directly as f_rng,
bypassing mbedtls_entropy. DER buffers heap-allocated to keep the
OSThread stack within budget. Cert + key + ip persisted under
/prefs/eth_*.der so subsequent boots reuse the same identity.
- Gated by HAS_ETHERNET_TLS_API. Standalone phase: generation only;
HTTPS server (TCP/443) wired up in the follow-up commit.
* feat(eth-tls-api): phase 2.2 — HTTPS server on TCP/443 reusing handlers
Brings up an mbedTLS server on port 443 that defers to the ECDSA P-256
self-signed cert produced by [[ethCert]]. Reuses the HTTP request /
response handlers from [[ethApiHandlers]] via the IStreamReadWrite
interface — there is exactly one code path for routing / CORS / PhoneAPI
integration regardless of whether the transport is plain TCP or TLS.
EthTlsApiServerThread (OSThread):
- Phase A: poll isEthCertReady() every 500 ms while the cert worker
runs. Once true, parse cert chain + key, build ssl_config (TLS server,
stream transport, default preset, VERIFY_NONE since we are the cert
issuer), install own cert, run ssl_setup, bind tlsServer on 443.
- Phase B: standard adaptive accept loop (20 / 100 / 500 ms tick),
identical to the plain-HTTP server.
Per-connection flow:
1. session_reset on the static ssl context (1 in-flight session — multi-
session pool is Phase 3 if needed)
2. set_bio routes mbedtls I/O to two C callbacks (netSend / netRecv)
that bridge to the live EthernetClient via the void* ctx
3. handshake loop (sync, blocking, with 10 s recv timeout) — mbedTLS
errors are logged with mbedtls_strerror
4. wrap (ssl, client) in MbedTlsStream → handleApiClient(stream)
5. close_notify + client.stop
Stack budget continues the Phase 2.1-bis discipline: every large buffer
(ssl context, cert chain, pk_key, ssl_config) lives in BSS as a static
global. The OSThread stack only holds the per-connection EthernetClient
adapter and small mbedtls return codes.
Validated on wiznet 192.168.1.143:
- cert load-from-FS path: 13 ms (regen skipped on second boot)
- cert gen path: 290 ms (first boot only)
- ssl_setup chain: parse cert, parse key, ssl_config_defaults,
conf_own_cert, ssl_setup all return 0
- end-to-end: curl -k https://192.168.1.143/api/v1/fromradio → 200 OK
with application/x-protobuf, CORS, X-Protobuf-Schema headers, server
initiates close_notify cleanly
Footprint vs 2.0:
- flash 70.5% → 87.3% (+220 KB for mbedtls_ssl + x509 server-side code)
- RAM static 17.6% → 19.8% (+11 KB BSS for ssl_context + cert chain)
- heap at runtime adds ~32 KB per active session (mbedtls in/out
record buffers, default MBEDTLS_SSL_*_CONTENT_LEN=16384)
Next: validate from Firefox direct (https://192.168.1.143 → warning
accept → JSON visible), then from client.meshtastic.org hosted to
confirm the mixed-content block is gone.
* fix(eth-tls): add KeyUsage + EKU serverAuth and cap TLS 1.2 for browser compat
Two browser-compat fixes that surfaced in Firefox validation:
1. Cert v1 only had Basic Constraints + SAN. NSS / Firefox refuse to
treat a cert as a TLS server cert without an Extended Key Usage
extension naming id-kp-serverAuth since 2023 — the error surfaces as
a non-overridable 'Secure Connection Failed' with no 'Accept the
Risk' path. Add KeyUsage(digitalSignature + keyEncipherment, critical)
and ExtendedKeyUsage(serverAuth, critical). Bump cert/key/ip file
paths to '_v2' so live boards regenerate on next start instead of
loading a v1 cert that the browser silently refuses.
2. pico-sdk mbedtls defines MBEDTLS_SSL_PROTO_TLS1_3 in its default
config, but the server-side 1.3 plumbing in this vendored build is
incomplete: Firefox and openssl-3.5's s_client default to 1.3 and
the handshake dies 4 ms in with MBEDTLS_ERR_ERROR_GENERIC_ERROR
(-0x0001). curl/SChannel happened to default to 1.2 so it masked the
issue earlier. Cap min/max_tls_version to TLS 1.2 — clients downgrade
transparently and we keep the ECDHE-ECDSA + AES-GCM / CHACHA20-POLY1305
suites that already work end-to-end.
Validated on wiznet 192.168.1.143:
- cert v2 dumps with the 4 extensions visible (openssl x509 -text):
BasicConstraints CA:FALSE, KeyUsage(critical) digitalSignature +
keyEncipherment, ExtendedKeyUsage(critical) serverAuth, SAN IP.
- openssl s_client (no version flag): downgrades to TLS 1.2, handshake
completes, verify_return=18 (self-signed, expected).
- Firefox: warning self-signed -> Advanced -> Accept Risk -> handshake
OK in 632 ms with CHACHA20-POLY1305, request reaches handleApiClient
and returns the protobuf body.
* perf(eth-api): HTTP/1.1 keep-alive — one handshake per session, not per request
Before this change /fromradio used 'Connection: close' framing (HTTP/1.0
style with no Content-Length), forcing each poll to redo the full TLS
handshake. client.meshtastic.org needs ~80 sequential /fromradio polls
during initial sync (one per packet from the config-replay state
machine: MyInfo, channels, every Config_*, every ModuleConfig_*, every
NodeInfo), so the user-visible load time was ~50 s of pure handshake
overhead (80 requests * ~625 ms ECDSA P-256 each).
Three coordinated changes:
1. handleApiClient() now loops on the same connection until the peer
closes or parseRequest hits its 3 s idle timeout. requestsServed
counter keeps the 'bad/timeout request' debug log from firing on
the natural idle close after a keep-alive sequence.
2. handleFromRadio() buffers all packets into a std::vector before
writing, so it can emit a real Content-Length and 'Connection:
keep-alive'. Buffer is dynamic — common 1-packet response only
allocates ~256 B; ?all=true keeps the 64-packet cap which tops out
around 16 KB. handleToRadio + sendPreflight switched to keep-alive
too (they already had real Content-Length). sendError keeps close —
errors are terminal.
3. ethTlsApiServer netRecv RECV_TIMEOUT_MS dropped from 10 s to 3 s so
mbedtls_ssl_read can't outlast the handler's idle deadline (a quiet
browser leaving the socket open would otherwise wedge the OSThread
for 10 s past the natural close).
Measured on wiznet 192.168.1.143 against client.meshtastic.org:
- one TLS handshake (641 ms, CHACHA20-POLY1305)
- ~80 requests pipelined over the same session
- full config + 40 NodeInfos in ~6-8 s (vs ~50 s before)
- per-request latency post-handshake: ~10-25 ms
- curl -kv with two URLs: 'Reusing existing https: connection',
server returns 'Connection: keep-alive' explicitly.
* fix(eth-tls): watchdog + Chrome compat — handshake stability across browsers
Phase 3 keep-alive shipped a working Firefox flow but client.meshtastic.org
loops + Chrome 'Test Connection' both rebooted the board. Four distinct
issues; collectively they kept the OSThread inside serveClient() too long
or spin-looping without yielding, and pico-sdk mbedtls' TLS 1.3 code path
choked on Chrome's modern ClientHello.
1. Watchdog reset during keep-alive idle. Once a client drained the
replay queue and entered 3 s poll mode, the OSThread sat inside
netRecv()'s busy-wait waiting for the next request. Two consecutive
3 s waits plus prior handler time crossed the 8 s RP2350 hardware
watchdog. Pet the watchdog inside netRecv()'s poll loop (every 2 ms)
so a quiet client can never starve the watchdog. Same fix in the
ethApiHandlers per-request yield path.
2. Cap session at 64 requests + yield() between. Defense-in-depth: a
pathological client can't monopolize serveClient indefinitely; after
the cap it just re-handshakes (~625 ms), still vastly cheaper than
the per-request handshake we had before keep-alive.
3. TLS 1.3 code compiled out of mbedtls entirely
(#undef MBEDTLS_SSL_PROTO_TLS1_3 in mbedtls_user_config). Capping
max_tls_version=TLS1_2 at runtime is enough for Firefox / openssl
(they downgrade cleanly), but Chrome's ClientHello carries TLS 1.3
extensions — post-quantum key shares, Encrypted ClientHello,
etc. — that the vendored mbedtls 1.3 parser crashes on before the
downgrade decision happens. Removing the 1.3 sources sidesteps the
parser; ServerHello just announces TLS 1.2 and Chrome accepts.
4. netSend infinite WANT_WRITE spin. When W5500's TX buffer momentarily
filled mid-handshake (Chrome draining slower than Firefox during
ServerKeyExchange), EthernetClient::write() returned 0, our netSend
returned MBEDTLS_ERR_SSL_WANT_WRITE without delay, mbedtls retried
immediately, repeat at ~180k iter/sec until ... well, until the
board's other threads got nothing done. Log signature: ret=-0x6880
tight-looping in the handshake iter trace. Rewrite netSend to block
with delay(2) + watchdog_update() and a 3 s timeout — same shape as
netRecv. Return MBEDTLS_ERR_SSL_PEER_CLOSE_NOTIFY on disconnect
(was incorrectly returning WANT_WRITE).
Also added granular per-iter handshake logging gated on first 20 iters
+ every 50th after that, so any future regression localizes itself in
COM9 without RTT JLink.
Validated on wiznet 192.168.1.143:
- Firefox: client.meshtastic.org full sync + idle poll stable (no
reset during the previously-crashing 'replay drain complete' phase)
- Chrome: 'Test Connection' accepts the cert prompt and connects
- Edge: same as Chrome
- openssl s_client default + tls1_2 forced: both negotiate TLS 1.2
with ECDHE-ECDSA + AES-GCM / CHACHA20-POLY1305, verify=18 (self-
signed, expected)
* chore(eth-tls): drop verbose debug logs from cert + TLS init paths
The cert pipeline + TLS context init had step-by-step LOG_INFOs and
ubiquitous Serial.flush() that were essential while diagnosing the
Phase 2.1-bis stack overflow, the Chrome handshake crash, and the
keep-alive watchdog reset. Once those bugs were fixed the logs just
clutter COM9 on every boot.
Kept on hand:
- cert: 'loaded from FS', 'generating ...', 'generated N B in T ms',
'persisted to LittleFS', plus all LOG_ERROR / LOG_WARN paths
- tls: 'server listening on TCP port 443', 'client connected from',
'handshake OK in N ms ciphersuite=', 'handshake failed -0xXXXX (...)',
plus all init LOG_ERRORs
Dropped:
- cert: 'step 1/8 pk_setup' through 'step 8/8 copy key DER', 'thread
woke', 'pipeline OK' (now silent on success)
- tls: 'cert is ready, initializing', 'parsing cert chain', 'parsing
key', 'ssl_config_defaults', 'conf_own_cert', 'ssl_setup',
'server worker scheduled', and the per-iter handshake trace
- obsolete 'Optional mbedtls debug bridge' commented-out stub
- all Serial.flush() that were added defensively for the
debug-the-crash phase
Bin shrinks ~40 KB (logs + format strings). Validated on wiznet
192.168.1.143: HTTP 200 round-trip works post-flash, no regression.
* fix(eth): harden API/TLS build guards (review #10573)
- ethApiHandlers.{h,cpp}: gate on (HAS_ETHERNET_API || HAS_ETHERNET_TLS_API)
so the shared handleApiClient/IStreamReadWrite still compile for an
HTTPS-only variant (the TLS server depends on them).
- ethTlsApiServer.{cpp,h}, ethCert.{cpp,h}: require ARCH_RP2040 (they use Pico
SDK get_rand_64()/watchdog_update()); the ethClient.cpp TLS include + call
site are tightened to match, so enabling the flag on a non-RP2040 Ethernet
target is a clean no-op instead of a cryptic build break.
- clang-format (16) the touched eth files to satisfy Trunk Check.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* fix(eth): address review — listener/cert recovery + keep-alive framing
- Rebind HTTP/80 and HTTPS/443 after a W5500 chip reset. reconnectETH() now
tears the API/TLS servers down (deInitEthApiServer/deInitEthTlsApiServer) so
the restart path recreates them; the singleton guards previously left both
bound to dead sockets until reboot. The workers are kept (only the listener
is dropped) so nothing is deleted from another thread's runOnce.
- Stop the keep-alive loop after a handler error. /fromradio and /toradio
return whether the connection may stay open; a 400/405/408 response
(Connection: close) now ends the loop so unread body bytes can't be parsed
as the next request.
- Validate the cached cert/key before trusting it (parse both DERs), and clear
the IP commit-marker before rewriting the pair and write it last, so a reset
mid-persist regenerates instead of handing the TLS server a truncated or
mismatched pair (which would hard-disable HTTPS).
- Track a cert generation counter so the TLS server reloads and rebinds when a
DHCP lease change regenerates the cert for a new IP (the SAN must follow, or
browsers reject the new address). The cert worker is no longer one-shot.
- Silence the SCons F821/E402 lint on add_mbedtls_sources.py to match the other
extra_scripts.
Validated on a W5500 board: a forced chip reset rebinds 80 and 443 without an
MCU reboot; a truncated cached cert regenerates and HTTPS recovers; a simulated
lease change reissues the cert with the new IP in the SAN.
* fix(eth): clear cert readiness on regen failure + verify cached pair
Follow-up to the review:
- Reset ready_/certIp_ when ensureCertForIp() fails, so isReady() no longer
reports true with empty material — otherwise a later TLS reload fails
initTlsContext() and stays disabled instead of retrying on the next poll.
- certKeyParse() now also checks the cached cert and key form a matching pair
(mbedtls_pk_check_pair), rejecting an independently-parseable but mismatched
cert/key (e.g. if the IP commit-marker survived a failed clear).
Validated on a W5500 board: a valid cached pair still loads from FS, and a
regenerated cert reloads cleanly.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* Fix T1000-E QMA6100P I2C probing
* Refactored to make generic
* address copilot comments
* fix(i2c): address copilot comments on QMA6100P scanning and hardware init
- ScanI2CTwoWire: gate bounded QMA6100P probing to addresses 0x12/0x13 only
(Copilot comment: avoid blocking other I2C device detection on nRF52)
Falls back to normal Wire probing for all other addresses, allowing BMM150
and other devices at overlapping addresses to be properly detected.
- Nrf52Twim: suppress cppcheck redundantAssignment on ENABLE register write
(intentional disable→configure→enable pattern for hardware safety; explicit
disable ensures known state before configuration even if already disabled)
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
* Nrf52Twim: gate on HAS_QMA6100P; suppress cppcheck redundantAssignment
The TWIM helper is only used by the QMA6100P probing path (T1000-E, the sole
board defining HAS_QMA6100P). It was gated only on ARCH_NRF52, so it compiled
as dead code on every other nRF52 board and was analyzed by the rak4631
cppcheck job -- which failed on a redundantAssignment false positive.
Gate the header and source on HAS_QMA6100P so the file is only built/analyzed
where it is actually used. Also keep an inline suppression on the ENABLE
re-assignment (a required volatile disable->reconfigure->enable sequence) for
the case where the T1000-E build is run through cppcheck locally.
Fixes the rak4631 cppcheck CI failure for PR #10713.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: nomdetom <nomdetom@protonmail.com>
Co-authored-by: Tom <116762865+NomDeTom@users.noreply.github.com>
Co-authored-by: Claude Haiku 4.5 <noreply@anthropic.com>
* Add gpsd support to portduino
* copilot fixes
* emit gps config in emit_yaml
* Fix formating to standard
* Address coderabitai issues
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* clarify channel number formatting and fix the fixed-width padded nodeIDs
* use the explicit 0x%08x for packets and nodeIDs throughout
* LLM instructions
Reconciles develop to master's latest renovate values for deps bumped on the
2.7 line but never back-merged, so the develop->master 2.8 promotion (#10777)
doesn't regress them. Done as a value reconcile, not a cherry-pick: several
master commits are superseded (5 device-ui bumps, 2 ststm32 bumps), and
develop's stale archive/refs/tags/ URL form actually blocked renovate from
bumping these (the regex expects archive/<version>.zip).
GitHub Actions:
- actions/checkout v6 -> v7 (35 refs)
- actions/cache v5 -> v6
- actions/github-script v8 -> v9 (3 refs)
- actions/stale v10.2.0 -> v10.3.0
Build / platform:
- alpine 3.23 -> 3.24 (alpine.Dockerfile)
- platformio/ststm32 19.5.0 -> 19.7.0
- platformio/nordicnrf52 10.11.0 -> 10.12.0
Libraries:
- Adafruit SSD1306 2.5.16 -> 2.5.17
- SparkFun MMC5983MA v1.1.4 -> v1.1.5
- Sensirion I2C SCD30 1.0.0 -> 1.1.1
- meshtastic esp8266-oled-ssd1306 6bfd1f1 -> 2e26010
Deliberately excluded:
- meshtastic/device-ui digest: coupled to firmware protobuf/API and develop has
diverged hard (NodeDB v25); left for a separate maintainer bump + visual check.
- libpax: develop uses the mverch67 fork (pinned by Arduino-3.x migration #9122),
master uses dbinfrago -- a fork divergence, not a version bump; not reconciled.
- platform-native digest: develop already at 61067ac (equal to master).
* fix se0fl-nodeID change
* address review: avoid redundant satellite erase + add braces in createNewIdentity
removeNodeByNum() already drops the satellite stores (and warm-tier copy) when it
removes the node, so only erase satellites directly in the rare case the lite entry
was already absent. Brace the removal block.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Document that src/mesh/generated is auto-generated and must not be edited
* Fix esp32s2 build by enabling native USB CDC, add S2 to check matrix (#10799)
* fix: stop unexpected NodeNum regeneration from PKI key loss
A node's NodeNum is derived from its PKI public key
(my_node_num == crc32(public_key)), so it changes only when the keypair is
regenerated -- which happens only when a keygen path runs while
config.security.private_key.size != 32. Two paths could trigger that without
the user intending a new identity:
1. Boot: loadFromDisk() collapsed every non-success loadProto() result for the
config file into installDefaultConfig() (preserveKey=false), which memset()s
config and wipes the private key. loadProto() distinguishes DECODE_FAILED
(file present but undecodable/undecryptable) from OTHER_FAILURE (absent), so
a transient/corrupt read silently minted a new identity. A new
configDecodeFailed flag now gates the boot keygen and the boot config-save
directly (not via region, so it survives the userprefs/region overrides that
run later in loadFromDisk): identity is frozen, the unreadable file is left
intact for a later clean boot to recover, and the node boots radio-silent
(region UNSET, TX off). A genuinely-absent config still gets defaults + keygen.
2. AdminModule security SET: config.security = c.payload_variant.security
wholesale-clobbered the keypair, then regenerated whenever the incoming
private_key.size != 32. A client editing an unrelated security field without
round-tripping the private key would re-mint identity. The existing keypair
is now preserved when the incoming config omits it; first provisioning and
key import are unchanged. Intentional reset goes through factory_reset.
Native PlatformIO unit suite (Docker): 499/499 test cases pass.
* test: cover security keypair preservation; clarify load-failure comment
Addresses PR review feedback:
- Add native unit tests (test_admin_radio) asserting handleSetConfig preserves the
existing identity keypair when a security SET omits the private key, and applies a
full supplied keypair (key import). Guards against reintroduced NodeNum/keypair
regeneration. AdminModuleTestShim (now a friend) defers saves so the lightweight
harness doesn't saveToDisk an uninitialized node database.
- Clarify the non-DECODE_FAILED config-load comment: OTHER_FAILURE / NO_FILESYSTEM
cover an absent or unopenable file, not just first boot.
* Disable gps thread on startup if lora region is unset
There is little reason to waste battery on the gps if the data cannot
yet be used.
* fix goobered merge
Refactor GPS enabling logic and remove duplicate code.
* trunk
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Add ARCH_PORTDUINO_WASM build: meshtasticd in WebAssembly over WebUSB
Compile the full portduino firmware to WebAssembly (Emscripten) so a real node runs in a browser tab or headless Node, driving a LoRa radio over WebUSB through a CH341 — the desktop Ch341Hal path with its libusb backend swapped for a WebUSB one. The native/desktop portduino build is unchanged.
New build env under src/platform/portduino/wasm/ (excluded from the native build_src_filter): WebUSB libpinedio backend, config/FS/region/MAC/PhoneAPI glue, wasm setup/loop, JS WebUSB runtime, and build stubs. bin/build-portduino-wasm.sh runs a standalone cached emcc build to build/wasm/meshnode.{mjs,wasm}.
Six firmware sources gain #ifdef ARCH_PORTDUINO_WASM guards (single-threaded cooperative emscripten_sleep loop, continuous RX, US region default, std RNG, no-popen exec); none affect non-wasm builds.
* PortDuino WASM: CI build job, cross-platform libdeps, configurable adapter
bin/build-portduino-wasm.sh: auto-detect native-macos (macOS) vs native (Linux/CI) libdeps with a NATIVE_ENV override, and use the SAME env's Crypto with an XEdDSA-present guard. Drops the heltec-v3/Crypto borrow — the meshtastic/Crypto pin already ships XEdDSA; the native libdeps cache was just stale. No env pin change.
Add .github/workflows/build_portduino_wasm.yml: build the ARCH_PORTDUINO_WASM target in CI (ubuntu + emsdk, native libdeps) so it can't silently bit-rot; asserts build/wasm/meshnode.{mjs,wasm}.
src/platform/portduino/wasm: add wasm_set_lora_* setters so the JS host can configure any CH341 LoRa adapter (module, USB ids, DIO/TCXO, SPI speed, pins); wasm_config_apply falls back to the MeshToad defaults when unset.
* WASM: build as a first-class [env:wasm] via platform-wasm (retire emcc script)
Replace the standalone emcc build (bin/build-portduino-wasm.sh) with a normal
PlatformIO env, `pio run -e wasm`, using the new meshtastic/platform-wasm
platform (emcc/em++ + Asyncify, the WASM sibling of platform-native). The
portduino WebAssembly node is now built the same way as every other target.
- variants/native/portduino/platformio.ini: add [env:wasm] (platform pinned to
platform-wasm, board wasm). Translates the script's source set into a curated
build_src_filter, the ~30 EXCLUDE_* defines, and the lib set; defines
ARCH_PORTDUINO_WASM in-repo so correctness doesn't hinge on the platform's
board.json.
- extra_scripts/wasm_link_flags.py: the firmware-specific emcc *link* settings
(EXPORT_NAME, EXPORTED_RUNTIME_METHODS, EXPORTED_FUNCTIONS, ASYNCIFY_IMPORTS).
PlatformIO feeds build_flags to compile only, so these must ride LINKFLAGS;
without it the WebUSB Asyncify seam and the JS host's runtime methods are
dropped (the _wasm_* exports survive only via EMSCRIPTEN_KEEPALIVE).
- PortduinoGlue.{h,cpp}: guard the yaml-cpp dependency out of the WASM build
(#ifndef ARCH_PORTDUINO_WASM around the include, emit_yaml/loadConfig/
readGPIOFromYaml). The browser node configures via the wasm_set_lora_* setters
and dead-strips the YAML path; this drops the host yaml-cpp build dependency
entirely. Native is unchanged (guards are inert there).
- portduino_glue_wasm.cpp / portduino_main_wasm.cpp: repair EM_ASM JS that a
formatter had mangled (!== -> != =, regex split) in the prior landing; the
emcc link succeeds regardless, so CI now runs `node --check meshnode.mjs`.
- .github/workflows/build_portduino_wasm.yml: build via `pio run -e wasm`
(artifacts under .pio/build/wasm/), trigger on the shared inputs the env
inherits (root platformio.ini, bin/platformio-*.py).
- NodeDB.cpp: drop the dead ARCH_PORTDUINO_WASM region-default branch (region
now defaults the same as native).
- Crypto renovate pins: add the missing gitBranch so they track upstream.
Output: .pio/build/wasm/meshnode.{mjs,wasm} (ES module, factory createMeshNode).
Verified: pio run -e wasm (against the published platform archive), node --check,
module instantiates in Node with all exports; native-macos + Docker native unit
tests (450/450) still pass.
* Fix name on the Piggystick
* wasm: pin platform-wasm at the GPL-3.0-relicensed commit
platform-wasm's LICENSE was always GPLv3 (matching this firmware), but its
platform.json/README still declared Apache-2.0 (mis-copied from platform-native).
That's fixed upstream in b83fa5b; bump the [env:wasm] pin to it. Build output is
unchanged (license metadata only). Verified: pio run -e wasm against b83fa5b.
* wasm: make reboot() actually restart the node (was a no-op)
In wasm the reboot path is live (main.cpp -> Power::powerCommandsCheck ->
Power::reboot), but Power::reboot's ARCH_PORTDUINO arm tore down SPI/Wire/Serial
and then called the no-op ::reboot() stub — leaving the node running with a dead
radio until the tab was manually reloaded. Triggers include an admin/phone
reboot, factory reset, the "reconfigure failed" path, and the 60 s stuck-TX
hardware watchdog (RadioLibInterface).
- Power::reboot(): add an ARCH_PORTDUINO_WASM arm (before ARCH_PORTDUINO, since
the wasm build defines both) that skips the host teardown and just calls
::reboot(). notifyReboot already let modules persist.
- ::reboot() (glue): hand off to the JS host — browser reloads the tab (NodeDB
state survives via IDBFS, same identity returns); headless calls Module.onReboot
if provided, else logs. Loose !=/== so clang-format doesn't mangle the EM_ASM JS.
- README: document the reboot handoff + the Module.onReboot hook.
Verified: pio run -e wasm + node --check (EM_ASM intact); native-macos unaffected.
* wasm: rename env to native-wasm and run it in the main CI matrix
Rename [env:wasm] -> [env:native-wasm] for consistency with the portduino
native family (native, native-macos, native-tft). The build dir follows to
.pio/build/native-wasm/ (artifact is still meshnode.{mjs,wasm}); the PIOENV
guard in extra_scripts/wasm_link_flags.py, the README, and the companion wrapper
move with it. The board stays `wasm`.
Also wire the build into normal CI: build_portduino_wasm.yml becomes a reusable
workflow (workflow_call) invoked as the `build-wasm` job of main_matrix.yml, so
the WebAssembly node is built like every other platform instead of on a separate
path trigger.
* native-wasm: auto-locate the Emscripten SDK (pre-build script)
`pio run -e native-wasm` failed with "emcc not found" whenever it was invoked
from a shell that hadn't sourced emsdk_env.sh — a VS Code task, an IDE build
button, a bare terminal. Add a pre: extra script that probes the usual emsdk
locations ($EMSDK_ENV, $EMSDK, ~/emsdk, ./.emsdk, the sibling companion
checkout), sources emsdk_env.sh, and imports the resulting environment so the
platform builder and emcc see PATH/EMSDK/EM_CONFIG. No-op when emcc is already
reachable (CI), silent when no SDK is found (the platform emits its own error).
* wasm: address PR review feedback
- js/bridge.js: import CH341 from "./ch341.js" (sibling in this layout), not
"../src/ch341.js" which doesn't resolve here.
- js/ch341.js: a zero-length transferIn while MISO bytes are still outstanding
now throws instead of breaking out with a partially-filled buffer — silent SPI
corruption becomes a loud error, matching the comment above it.
- libpinedio_webusb.c: webusb_set_auto_cs honors the AUTO_CS option (? 1 : 0)
instead of the always-on ? 1 : 1. Runtime behavior is unchanged — Ch341Hal sets
AUTO_CS=0 right after pinedio_init (RadioLib drives the active-low NSS); the
option just isn't set yet at init, so this now correctly defaults off.
- SX126xInterface.cpp: the RX-start error log now names the method actually
called (startReceive vs startReceiveDutyCycleAuto) instead of hardcoding the
duty-cycle name in the WASM branch.
* native-wasm: drop the emsdk bootstrap shim (now in platform-wasm)
The Emscripten SDK auto-location moved into the platform-wasm builder, so the
firmware no longer needs its own pre: extra script. Remove
extra_scripts/wasm_emsdk_env.py and bump the platform pin to the build that
carries the bootstrap. The wasm_link_flags.py post script stays — those exported
fns / runtime methods / Asyncify import seam are firmware-app-specific.
* wasm: use the canonical companion name (meshtasticd-wasm-node)
The companion repo was renamed meshtastic-web-node -> meshtasticd-wasm-node; fix
the stale name in the wasm README and bump the platform pin to the build that
promotes the canonical name in its emsdk auto-location.
* wasm: re-entrancy guard for the API/region entry points + flaky-open retry
Two robustness fixes for the browser node:
- Re-entrancy guard. The node is single-threaded + Asyncify: while setup()/loop()
is suspended inside a WebUSB transfer, the JS event loop is free, so a stray
DOM/timer callback that re-enters a wasm_* entry point starts a second Asyncify
unwind ("async operation already in flight" abort) or clobbers shared PhoneAPI
state (observed as a "PhoneAPI::available unexpected state" flood). Add a
g_wasm_in_firmware flag set around setup()/loop() (portduino_main_wasm.cpp); the
wasm_set_region / wasm_api_to_radio / wasm_api_from_radio / wasm_api_available
entry points now reject a mid-tick call (return busy) instead of corrupting or
aborting. The host must still call them between ticks — this is the safety net
the design lacked, not a substitute for the JS queue.
- CH341 open retry (js/bridge.js). First-connect WebUSB is flaky — the interface
is briefly unclaimable right after the grant, or held by a prior session,
giving a transient "Could not open SPI: -1". Retry the open with a short
backoff, closing the device between attempts so claimInterface starts clean.
* wasm: exclude emscripten-only sources from cppcheck
The `check` board matrix runs `pio check` (cppcheck) over all of src/,
including src/platform/portduino/wasm/. cppcheck can't parse the EM_ASYNC_JS/
EM_JS macros (Syntax Error: AST broken at libpinedio_webusb.c:39,
internalAstError) and these sources are not part of any checked board build
([env:native-wasm] is board_level=extra, compiled by the build-wasm CI job).
Suppress the wasm dir in suppressions.txt, the same way generated/ and .pio/
are already excluded.
* wasm: coalesce FS.syncfs so two never run at once
IDBFS syncfs is async; the explicit wasm_fs_sync (5s timer + post-save +
beforeunload) could overlap a prior in-flight sync, warning "2 FS.syncfs
operations in flight at once". Serialize: if a sync is running, mark a pending
re-sync and let the in-flight one chain it on completion — at most one in flight,
trailing writes still flushed. (Companion drops IDBFS autoPersist so this is the
single persistence path.)
* wasm: silence false-positive SAST on the emscripten glue
- extra_scripts/wasm_link_flags.py: restore the trunk-ignore-all(ruff/F821,
flake8/F821) header every other SCons extra_script carries; Import/env are
SConscript-injected globals, so ruff/flake8 flag them as undefined.
- .semgrepignore: exclude src/platform/portduino/wasm/js/ (browser WebUSB glue,
not part of the firmware binary). The unsafe-formatstring rule false-positives
on its benign retry/diagnostic console logs.
* Update .github/workflows/build_portduino_wasm.yml
Co-authored-by: Austin <vidplace7@gmail.com>
---------
Co-authored-by: Austin <vidplace7@gmail.com>
* InkHUD: map tile background, zoom controls, and GPS live tracking
- Map background tiles are now rendered on the display when available, compressed with LZ4 to keep flash usage low
- If no map tiles are loaded, the map applets behave exactly as before
- Zoom in, zoom out, and reset zoom (back to auto-fit) are accessible from the menu, and only appear when the menu is opened from a map screen
- The map updates automatically whenever GPS gets a new position or your phone shares a location
- The Positions and Favorites map applets now also refresh when mesh position packets arrive for your own node
- The Favorites map now shows your position on the map even if you have no favorites yet
* README Update
* Update MapApplet.cpp
* Zoom fixed
* Zoom with no tiles fix
* CI fix
* Tips robot virtual node / relayer to different LoRa modes & channels
Note that this commit has details hardcoded for the Wellington (NZ)
mesh, and also requires the following patch to the protobufs:
-----
diff --git a/meshtastic/mesh.proto b/meshtastic/mesh.proto
index 03162d8..ec54c99 100644
--- a/meshtastic/mesh.proto
+++ b/meshtastic/mesh.proto
@@ -1393,6 +1393,21 @@ message MeshPacket {
* Set by the firmware internally, clients are not supposed to set this.
*/
uint32 tx_after = 20;
+
+ /*
+ * The modem preset to use fo rthis packet
+ */
+ uint32 modem_preset = 21;
+
+ /*
+ * The frequency slot to use for this packet
+ */
+ uint32 frequency_slot = 22;
+
+ /*
+ * Whether the packet has a nonstandard radio config
+ */
+ bool nonstandard_radio_config = 23;
}
/*
-----
* fix: repair mesh tips CI build
* feat: add MeshBeacon module (Phase 1 — proto + generated code + initial stub)
* feat(beacon): implement broadcaster + listener (phases 2-5)
* feat(beacon): wire RadioLibInterface hooks + admin validation (phases 6-7)
* fix(beacon): fix LocalModuleConfig flat access (no payload_variant), add localonly proto field
* feat(beacon): fix broadcaster inheritance, add preset/region validation + proto cache
- MeshBeaconBroadcastModule now inherits ProtobufModule<meshtastic_MeshBeacon>
(alongside private MeshBeaconModule + OSThread), giving it allocDataPacket()
and setStartDelay() without extra includes.
- Payload cache: rebuildCache() encodes the MeshBeacon protobuf once and stores
it in payloadCache[]/payloadCacheSize; sendBeacon() only calls rebuildCache()
when payloadCacheDirty==true. AdminModule calls invalidateCache() after saving
new config so the next broadcast picks up changes.
- Region/preset validation in handleSetModuleConfig (mesh_beacon_tag):
broadcast_on_preset is validated against the device's current region via
RadioInterface::validateConfigLora(); broadcast_offer_region is validated via
RadioInterface::validateConfigRegion(). Invalid values are zeroed with a
LOG_WARN before saving.
* feat(beacon): add unit tests for MeshBeaconModule and AdminModule configuration validation
* remove old meshtips
* more validation in NodeDB and AdminModule, and userprefs for baked in goodness
* copilot is my gravity
* mmmmm... beacon
* oops
* Enhance unit tests for MeshBeaconModule with detailed validation checks and output formatting
* new lines. Why not?
* finally
* legacy mode activate!
* Update protobufs (#17)
Co-authored-by: NomDeTom <116762865+NomDeTom@users.noreply.github.com>
* better logic, fixed a test
* updated for packet signing
fixed a test
added guards for licensed/ham mode
* channel numbers
* beacon: encrypt on the beacon channel PSK; fix split note
When broadcast_on_channel overrides the primary channel's name/PSK, the
beacon was encrypted with the PRIMARY PSK: perhapsEncode keys encryption
off the primary slot, but the radio-thread channel switch happens only
after encryption. sendBeaconPacket() now installs the beacon channel into
the primary slot for the synchronous duration of send() (cooperative
threading => no interleaving) so encryption/hash use the beacon channel,
then restores it. A shared beaconChannelSettings() helper builds the
channel for both the encrypt-time swap and the RF-time swap so the
key+hash cannot drift.
Also: correct the legacy-split comments (both packets go out on the same
beacon radio settings, not the normal config) and merge the two
consecutive `if (hasText)` blocks in the listener (cppcheck
duplicateCondition).
Tests: add channelPskOverride_swapsBeaconChannelAndRestores and
noChannelOverride_doesNotSwapPrimary; MockRouter snapshots the primary
channel at send() time.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* test/beacon: drain toPhoneQueue in tearDown to fix LSan leak abort
The listener delivers received text via MeshService::sendToPhone(), which
enqueues the packet into toPhoneQueue and takes ownership. Nothing dequeues
it in tests, so the three listener tests carrying message text stranded a
MeshPacket each — 1272 bytes / 3 allocations that LeakSanitizer flagged at
process exit, aborting the coverage run (surfaced by pio as [ERRORED] /
SIGHUP even though all 40 assertions passed).
Drain the phone queue in tearDown (getForPhone()/releaseToPool) so the
packets return to packetPool. Suite is now GREEN with no sanitizer abort.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* legacy hop override for zero-hoppers
* ever more beacons
* beacon: comment out broadcast_send_as_node pending further review
Functionality preserved in comments with full signing/has_bitfield notes
for when it is re-enabled. Proto tag 3 retained on the wire.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* test/beacon: fix fromIsCustomNodeWhenSet now that send-as-node is disabled
broadcast_send_as_node is commented out; from is always the local node.
Update the test assertion and doc comment to match current behaviour.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* Update protobufs (#21)
Co-authored-by: NomDeTom <116762865+NomDeTom@users.noreply.github.com>
* flags for beacons
* beacon: do more with less — slot-index targets + validation
Multi-target beacons embedded a full ChannelSettings in every BroadcastTarget,
blowing ModuleConfig past the 512-byte BLE FromRadio budget so the firmware would
not compile. Targets now reference an existing channel-table slot by channel_index
and the broadcaster resolves it via channels.getByIndex() at TX time. Net effect:
the same multi-target capability for a fraction of the bytes —
FromRadio 609 -> 510 B, MeshBeaconConfig 596 -> 324 B, AdminMessage 615 -> 511 B.
- proto: BroadcastTarget.channel (embedded) -> channel_index (uint32 ref); regen all
generated headers (size constants propagate to admin/localonly/deviceonly/mesh).
- broadcaster: resolve channel_index from the channel table; an out-of-range or blank
slot falls back to the default channel for the target preset rather than borrowing
the primary's name/PSK.
- AdminModule: validate broadcast_targets entries on write (region/preset sanitised
like the single-target fields; channel_index range-checked).
- userPrefs: TARGET_<n>_CHANNEL_{NAME,NUM,PSK} collapse to a single CHANNEL_INDEX.
- docs: two-step (set_channel -> set_module_config) multi-target setup, inline-vs-
reference distinction, and single-/multi-target are equal (not "legacy") options.
- tests: target validation + channel-index resolution incl. blank-slot fallback
(47/47 green on `./bin/run-tests.sh -e native -f test_mesh_beacon`).
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01NRAF5csgsMn6p1zEcFL8Qz
* throttling after reboot
* address copilot review
* simplify
* fix(beacon): use 0x%08x for node/packet IDs in logs; register test suite
The %#08lx log specifiers passed uint32_t (NodeNum/PacketId) to a %lx
length modifier — undefined behaviour on 64-bit (native test) targets and
non-standard width. Switch to the project-standard 0x%08x. Also bump
test/native-suite-count to 25 for the added test_mesh_beacon suite.
clod helped too
* copilot & clarity
clod helped too
* refactor(beacon): use auto for the sanitized config copy
clod helped too
* fix(beacon): guard empty-payload sends; gate has_mesh_beacon on build flag; document ISR_TX pre-switch
clod helped too
---------
Co-authored-by: Steve Gilberd <steve@erayd.net>
Co-authored-by: Darafei Praliaskouski <me@komzpa.net>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
* esp32: release BTDM heap when Bluetooth inactive
Release ESP-IDF BTDM memory after config load when Bluetooth is disabled or WiFi is enabled, recovering heap on ESP32 targets where BLE won’t be used for this boot.
* Address BT memory release review comments
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Make the PowerFSM DARK-to-LS timeout immediate when Bluetooth support is compiled out or config.bluetooth.enabled is false. The configured wait_bluetooth_secs default behavior is unchanged when Bluetooth is enabled.
configs for raspberry pi and luckfox lyra zero
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
(cherry picked from commit bfc206a47b64738575b8039733e663218870398b)
* Enhance RTC handling with unit test support for system time fallback
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
(cherry picked from commit c7f17a80b26a4a0ef151f5c1ba9342e7e1e205ed)
Forward-port of #10754 and #10757 from master (2.7) into develop, so the
develop->master 2.8 promotion (#10777) doesn't drop them.
#10754: PhoneAPI no longer walks the filesystem to build the file manifest on
node-info-only config requests (SPECIAL_NONCE_ONLY_NODES), which never consume
it. getFiles() is now bounded (default 64 entries, depth 3) via collectFiles(),
takes an optional wasLimited out-param, and reserves capacity with a bad_alloc/
length_error fallback. The manifest vector is freed via swap (releaseFilesManifest).
#10757: getFiles()/collectFiles() now guard against empty file names returned by
the Adafruit LittleFS nRF52 glue (issue 4395).
Ported by hand rather than cherry-picked: master had reflowed FSCommon.cpp to a
different brace style (every line conflicted), #10754 already subsumes #10757,
and develop carries a MESHTASTIC_EXCLUDE_FILES_MANIFEST path (nRF54L15) that
master lacks. The exclude path is preserved and now also short-circuits + frees
the manifest. Verified: native Docker suite 448/448, clang-format clean.
* Guard TCP API writes against dead sockets
Agent-Logs-Url: https://github.com/meshtastic/firmware/sessions/ebeb38d5-7339-4eac-b310-4b6dd9d40758
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* fix: apply review fixes for server write checks and stream locking
Agent-Logs-Url: https://github.com/meshtastic/firmware/sessions/215c659d-bc17-4b30-89f4-78e3f9cdb3c3
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* style: format TCP API write check files
* fix(api): keep TCP API open on write backpressure; drop broken writability gate
canWriteFrame() treated a full transmit buffer (availableForWrite() == 0) as a
dead socket and closed the connection, so every healthy client was dropped and
the native simulator integration test timed out waiting for config. A zero
availableForWrite() is normal backpressure, not a disconnect; only a dropped
link should refuse a write. Reduce canWriteFrame() to the reliable
!client.connected() check -- genuine write failures are still caught after the
fact by onFrameWriteFailed().
Remove the now-unused ClientWriteChecks.h writability helper and its unit test
(test_client_write_checks, which also failed to link), and restore
ServerAPI.cpp to the project clang-format style (fixes the Trunk check).
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
---------
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Claude Opus 4.8 <noreply@anthropic.com>
Thomas GöttgensandGitHub
Jonathan BennettandGitHub
AustinandGitHub
ManuelandBen Meadors
LittleatonandBen Meadors
jessm33
