* Make phone queues use a static pointer queue
* Static init
* Compile time constants now
* Instead, lets just use the normal pointerqueue for linux native builds and static for IoT platforms
* Add missing method
* Missing methods
* Update variant.h
Further to https://github.com/meshtastic/firmware/pull/7897 ,
there was another log line that was triggering indiscriminantly on
GPS_INTERVAL_THRESHOLD .
Rather than logging a bad time 4000 times, let's just log one good time
when it is set.
Further to https://github.com/meshtastic/firmware/pull/7897 ,
there was another log line that was triggering indiscriminantly on
GPS_INTERVAL_THRESHOLD .
Rather than logging a bad time 4000 times, let's just log one good time
when it is set.
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Fix excluded modules configuration handling
- Add excluded_modules flags in getDeviceMetadata() for MQTT, PAXCOUNTER, STOREFORWARD, RANGETEST, NEIGHBORINFO
- Add conditional compilation guards in AdminModule for RANGETEST, AUDIO, PAXCOUNTER, STOREFORWARD, EXTNOTIF, DETECTIONSENSOR, AMBIENTLIGHTING
- Add skip logic in PhoneAPI for excluded modules during config enumeration
- Add conditional has_* flags in NodeDB only for included modules
Fixes issue where excluded modules still appeared in client applications and sometimes caused PAYLOADVARIANT_NOT_SET errors.
* Fix excluded modules issues and refactor code
- Restore original PAXCOUNTER logic: only exclude on non-ESP32 platforms due to memory constraints
- Fix has_store_forward flag to be conditionally compiled based on MESHTASTIC_EXCLUDE_STOREFORWARD
- Refactor PhoneAPI module config skipping logic to use helper function skipExcludedModuleConfig()
- Reduce code duplication in PhoneAPI by extracting common skip logic
This addresses the three issues identified in the code review:
1. PAXCOUNTER memory impact on non-ESP32 devices
2. Unconditional has_store_forward flag setting
3. Duplicated state management logic across multiple #else blocks
* Fix ambient lighting module exclusion in PhoneAPI and AdminModule
- Add conditional compilation guards for ambient lighting in PhoneAPI.cpp
- Replace old HAS_RGB_LED logic with MESHTASTIC_EXCLUDE_AMBIENTLIGHTING check in AdminModule.cpp
- Ensure ambient lighting module is properly excluded when MESHTASTIC_EXCLUDE_AMBIENTLIGHTING=1
* Phone GPS display on Position Screen
This is a PR to show when a phone shares GPS location with the node so you can reliably know what coordinate is being shared with the Mesh.
* Account for low resolution wide screen OLEDs
* Allow picking of Device Role and new Display Formatter for Device Role
* Add remainder of client roles to display formatter
* Don't update the role unless you pick a value
* Mascots are fun
* Fix warnings during compile time
* Improve some menus
* Mascots need to work everywhere
* Update Chirpy image
* Fix Trunk
* Update protobufs
* Add date to Clock screen
* Analog clocks love dates too
* Finalize date moves for analog clock
* Add a new GPS model CM121.
* Add CM121 to Unicore.
* Trunk fixes, remove unneded NMEA lines
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Adding a counter to show the last time a GPS coordinate was detected to ensure the user is aware how long since the coordinate updated or to identify any errors.
* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
* Show ExternalNotification as excluded if it is
* Enable ExternalNotification, SerialModule and RangeTest on STM32WL
* Misc fixes for #7797 - ARCH_STM32 -> ARCH_STM32WL, use less flash by dropping weather station support for serialmodule, set tx/rx pins before begin
* Enable Serial1 on RAK3172, make SerialModule use it (console is on LPUART1)
* Fix SerialModule on RAK3172, fix board definition of RAK3172 to include the right pin mapping.
* Show ExternalNotification as excluded if it is
* Enable ExternalNotification, SerialModule and RangeTest on STM32WL
* Misc fixes for #7797 - ARCH_STM32 -> ARCH_STM32WL, use less flash by dropping weather station support for serialmodule, set tx/rx pins before begin
* Enable Serial1 on RAK3172, make SerialModule use it (console is on LPUART1)
* Fix SerialModule on RAK3172, fix board definition of RAK3172 to include the right pin mapping.
* Fix GPS that hard code 2080 as the start time.
Some GPS chips, such as the AG3335 in T1000e and L96 have a hardcoded
time of 2080-01-05 when they start up.
To fix that in a way that seems permanent, let's ignore times that
are more than 40 years since the firmware was built. We should followup
in late 2039 to see if any changes are needed.
Reported-By: @b8b8
* Update src/gps/RTC.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Put FORTY_YEARS in header and use in both places.
* Restore Ben's nicer log lines.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix GPS that hard code 2080 as the start time.
Some GPS chips, such as the AG3335 in T1000e and L96 have a hardcoded
time of 2080-01-05 when they start up.
To fix that in a way that seems permanent, let's ignore times that
are more than 40 years since the firmware was built. We should followup
in late 2039 to see if any changes are needed.
Reported-By: @b8b8
* Update src/gps/RTC.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Put FORTY_YEARS in header and use in both places.
* Restore Ben's nicer log lines.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Hold for >20s after GPS lock
GPS chips are designed to stay locked for a while to download some data and save it.
This data is important for speeding up future locks, and making them higher quality.
Our present configuration could make every lock perform similar to first lock.
This patch sets a hold of between 20s and 10% of the lock search time after lock
is acquired. This should allow the GPS to finish its work before we turn it off.
Fixes https://github.com/meshtastic/firmware/issues/7466
* Remove T1000E-specific GPS holds
The new code does the same thing, for all devices.
* Fix publishing settings
* Cleanups, removing unused variables.
* ifdef log line with GPS_DEBUG
* fixQual is not a bool.
* Hold for >20s after GPS lock
GPS chips are designed to stay locked for a while to download some data and save it.
This data is important for speeding up future locks, and making them higher quality.
Our present configuration could make every lock perform similar to first lock.
This patch sets a hold of between 20s and 10% of the lock search time after lock
is acquired. This should allow the GPS to finish its work before we turn it off.
Fixes https://github.com/meshtastic/firmware/issues/7466
* Remove T1000E-specific GPS holds
The new code does the same thing, for all devices.
* Fix publishing settings
* Cleanups, removing unused variables.
* ifdef log line with GPS_DEBUG
* fixQual is not a bool.
ford-jones
Ben Meadors
Tom FifieldandBen Meadors
ManuelandGitHub
Dmitry DubininandGitHub
Jason PandGitHub
GUVWAFandGitHub
HarukiToredaandGitHub
Chloe BethelandBen Meadors
Jonathan BennettandBen Meadors