Thomas Göttgens
80f8611e65
* fix(sx126x): allow boards to opt out of the PA optimization table Boards driving an external PA can define SX126X_NO_POWER_OPTIMIZATION_TABLE to use the fixed PA config instead of RadioLib's table, which is tuned for a bare SX126x. Default behaviour is unchanged. init() applies the fixed config after begin(), which programs power through the table. * feat(variants): add Seeed Wio Tracker L1 Pro 1W nRF52840 + SX1262 with a 1 W external PA, L76K GNSS, SH1106 OLED. Uses hw_model 144 (meshtastic/protobufs#1038), opts into SX126X_NO_POWER_OPTIMIZATION_TABLE and declares SX126X_MAX_POWER explicitly. The PA gain table is indexed by SX1262 output power in dBm. Requires protobufs#1038 and a protobuf regen before it builds. * chore(deps): bump RadioLib to 510e00cf Carries the current LR11x0 and LR2021 fixes. * fix(variants): correct L1 Pro 1W QSPI pins and clean up comments PIN_QSPI_* are logical pin indices. The QSPI flash sits at D19-D24 in variant.cpp, but the defines carried D21-D26 from seeed_solar_node, where that block does start at D21. D25 and D26 are trackball pins. Also replaces mis-encoded characters in the pin comments and drops the migration note, which referenced a private repo path and a stale PINS_COUNT. * fix(variants): move L1 Pro 1W out of the per-PR build matrix board_level = pr is the high-attention tier that builds on every PR. This board belongs with the mainline set, which uses board_level = release.
58 lines
1.3 KiB
JSON
58 lines
1.3 KiB
JSON
{
|
|
"build": {
|
|
"arduino": {
|
|
"ldscript": "nrf52840_s140_v7.ld"
|
|
},
|
|
"core": "nRF5",
|
|
"cpu": "cortex-m4",
|
|
"extra_flags": "-DARDUINO_MDBT50Q_RX -DNRF52840_XXAA",
|
|
"f_cpu": "64000000L",
|
|
"hwids": [
|
|
["0x2886", "0x1668"],
|
|
["0x2886", "0x1667"]
|
|
],
|
|
"usb_product": "TRACKER L1 Pro 1W",
|
|
"mcu": "nrf52840",
|
|
"variant": "seeed_wio_tracker_L1_Pro_1W",
|
|
"bsp": {
|
|
"name": "adafruit"
|
|
},
|
|
"softdevice": {
|
|
"sd_flags": "-DS140",
|
|
"sd_name": "s140",
|
|
"sd_version": "7.3.0",
|
|
"sd_fwid": "0x0123"
|
|
},
|
|
"bootloader": {
|
|
"settings_addr": "0xFF000"
|
|
}
|
|
},
|
|
"connectivity": ["bluetooth"],
|
|
"debug": {
|
|
"jlink_device": "nRF52840_xxAA",
|
|
"svd_path": "nrf52840.svd",
|
|
"openocd_target": "nrf52840-mdk-rs"
|
|
},
|
|
"frameworks": ["arduino"],
|
|
"name": "seeed_wio_tracker_L1_Pro_1W",
|
|
"upload": {
|
|
"maximum_ram_size": 248832,
|
|
"maximum_size": 815104,
|
|
"speed": 115200,
|
|
"protocol": "nrfutil",
|
|
"protocols": [
|
|
"jlink",
|
|
"nrfjprog",
|
|
"nrfutil",
|
|
"stlink",
|
|
"cmsis-dap",
|
|
"blackmagic"
|
|
],
|
|
"use_1200bps_touch": true,
|
|
"require_upload_port": true,
|
|
"wait_for_upload_port": true
|
|
},
|
|
"url": "https://www.seeedstudio.com/Wio-Tracker-L1-Pro-p-6454.html",
|
|
"vendor": "Seeed Studio"
|
|
}
|