c51c01607d
Adds the Traffic Management module (TMM) plus the NodeDB/warm-store and next-hop foundations it builds on: - Unified per-node cache (flat array, 8-bit relative ticks) shared by all features; role-aware throttles for tracker / lost-and-found. - Position deduplication: drop unchanged position rebroadcasts within a configurable interval; precision driven off the channel ceiling (clamped to the public-key max on well-known channels). Enabled by default at 11h. - Per-node rate limiting and unknown-packet filtering (config-driven; a non-zero companion field enables each feature -- no bool toggles). - NodeInfo direct response from cache with role-based hop clamps. - Persistent next-hop overflow store: confirmed hops have no TTL, are seeded from NodeInfoLite at boot, and survive hot-store eviction. - Three-tier sender-role resolution (hot NodeInfoLite -> warm store -> TMM cache). Role is cached write-time (seeded on first track, refreshed from NodeInfo), pins its cache entry like a next-hop hint, and is evicted last. - Warm store caches device role + protected category across reboot/eviction. - PositionModule stationary floor for tracker / lost-and-found. - PSRAM gating for warm/satellite/TMM cache sizes; STM32WL excluded. Protobufs: TrafficManagementConfig trimmed to the five uint32 fields actually used; submodule repointed to protobufs develop. Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
70 lines
2.6 KiB
C
70 lines
2.6 KiB
C
#define VEXT_ENABLE 40 // active low, powers the oled display and the lora antenna boost
|
|
#define VEXT_ON_VALUE LOW
|
|
#define BUTTON_PIN 0
|
|
|
|
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
|
#define ADC_CHANNEL ADC_CHANNEL_0
|
|
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
|
|
#define ADC_MULTIPLIER 4.9 * 1.035
|
|
|
|
#define USE_SX1262
|
|
#define LORA_DIO0 -1 // a No connect on the SX1262 module
|
|
#define LORA_RESET 12
|
|
#define LORA_DIO1 14 // SX1262 IRQ
|
|
#define LORA_DIO2 13 // SX1262 BUSY
|
|
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TCXO is enabled
|
|
|
|
#define LORA_SCK 9
|
|
#define LORA_MISO 11
|
|
#define LORA_MOSI 10
|
|
#define LORA_CS 8
|
|
|
|
#define SX126X_CS LORA_CS
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
|
|
|
// Enable Traffic Management Module for Heltec V4
|
|
#ifndef HAS_TRAFFIC_MANAGEMENT
|
|
#define HAS_TRAFFIC_MANAGEMENT 1
|
|
#endif
|
|
|
|
// ---- KCT8103L RF FRONT END CONFIGURATION ----
|
|
// The Heltec V4.3 uses a KCT8103L FEM chip with integrated PA and LNA
|
|
// RF path: SX1262 -> Pi attenuator -> KCT8103L PA -> Antenna
|
|
// Control logic (from KCT8103L datasheet):
|
|
// Transmit PA: CSD=1, CTX=1, CPS=1
|
|
// Receive LNA: CSD=1, CTX=0, CPS=X (21dB gain, 1.9dB NF)
|
|
// Receive bypass: CSD=1, CTX=1, CPS=0
|
|
// Shutdown: CSD=0, CTX=X, CPS=X
|
|
// Pin mapping:
|
|
// CPS (pin 5) -> SX1262 DIO2: TX/RX path select (automatic via SX126X_DIO2_AS_RF_SWITCH)
|
|
// CSD (pin 4) -> GPIO2: Chip enable (HIGH=on, LOW=shutdown)
|
|
// CTX (pin 6) -> GPIO5: Switch between Receive LNA Mode and Receive Bypass Mode. (HIGH=RX bypass, LOW=RX LNA)
|
|
// VCC0/VCC1 -> Vfem via U3 LDO, controlled by GPIO7
|
|
// KCT8103L FEM: TX/RX path switching is handled by DIO2 -> CPS pin (via SX126X_DIO2_AS_RF_SWITCH)
|
|
|
|
#define USE_KCT8103L_PA
|
|
#define LORA_PA_POWER 7 // VFEM_Ctrl - KCT8103L LDO power enable
|
|
#define LORA_KCT8103L_PA_CSD 2 // CSD - KCT8103L chip enable (HIGH=on)
|
|
#define LORA_KCT8103L_PA_CTX 5 // CTX - Switch between Receive LNA Mode and Receive Bypass Mode. (HIGH=RX bypass, LOW=RX LNA)
|
|
|
|
#if HAS_TFT
|
|
#define USE_TFTDISPLAY 1
|
|
#endif
|
|
/*
|
|
* GPS pins
|
|
*/
|
|
#define GPS_L76K
|
|
#define PIN_GPS_EN (42)
|
|
#define GPS_EN_ACTIVE LOW
|
|
#define PERIPHERAL_WARMUP_MS 1000 // Make sure I2C QuickLink has stable power before continuing
|
|
#define PIN_GPS_PPS (41)
|
|
// Seems to be missing on this new board
|
|
#define GPS_TX_PIN (38) // This is for bits going TOWARDS the CPU
|
|
#define GPS_RX_PIN (39) // This is for bits going TOWARDS the GPS
|
|
#define GPS_THREAD_INTERVAL 50
|