增加e22-400M33S

Signed-off-by: kevin <kevin@lmve.net>

code/firmware-2.7.15.567b8ea/src/mesh/RadioInterface.cpp

@@ -58,7 +58,7 @@ const RegionInfo regions[] = {
     /*
         https://lora-alliance.org/wp-content/uploads/2020/11/lorawan_regional_parameters_v1.0.3reva_0.pdf
      */
-    RDEF(CN, 470.0f, 510.0f, 100, 0, 19, true, false, false),
+    RDEF(CN, 470.0f, 510.0f, 100, 0, SETTING_MAX_POWER, true, false, false),
 
     /*
         https://lora-alliance.org/wp-content/uploads/2020/11/lorawan_regional_parameters_v1.0.3reva_0.pdf

code/firmware-2.7.15.567b8ea/variants/esp32c3/diy/esp32c3_moonshine/pins_arduino.h

@@ -6,8 +6,8 @@
 static const uint8_t TX = 21;
 static const uint8_t RX = 20;
 
-static const uint8_t SDA = 1;
-static const uint8_t SCL = 0;
+static const uint8_t SDA = 12;
+static const uint8_t SCL = 13;
 
 static const uint8_t SS = 8;
 static const uint8_t MOSI = 7;

code/firmware-2.7.15.567b8ea/variants/esp32c3/diy/esp32c3_moonshine/platformio.ini

@@ -9,6 +9,8 @@ build_flags =
   ${esp32c3_base.build_flags}
   -D PRIVATE_HW
   -I variants/esp32c3/diy/esp32c3_moonshine
+  -D ARDUINO_USB_MODE=1
+  -D ARDUINO_USB_CDC_ON_BOOT=1
 monitor_speed = 115200
 upload_protocol = esptool
 ;upload_port = /dev/ttyUSB0

code/firmware-2.7.15.567b8ea/variants/esp32c3/diy/esp32c3_moonshine/variant.h

@@ -4,17 +4,30 @@
 // https://resource.heltec.cn/download/HT-CT62/HT-CT62_Reference_Design.pdf
 // https://resource.heltec.cn/download/HT-DEV-ESP/HT-DEV-ESP_V3_Sch.pdf
 
+#define HAS_SCREEN 0
 
-#define LED_POWER 12    // LED
+#define HAS_I2C 0
+#define WIRE_INTERFACES_COUNT (0)
+#define I2C_SDA 12
+#define I2C_SCL 13
+
+
+
+#define BATTERY_PIN            1
+#define ADC_CHANNEL            ADC1_GPIO1_CHANNEL
+#define ADC_MULTIPLIER         2.0f
+
+#define LED_POWER 0    // LED
 #define LED_STATE_ON 1 // State when LED is lit
 
-#define HAS_SCREEN 0
+
 #define HAS_GPS 0
 #undef GPS_RX_PIN
 #undef GPS_TX_PIN
 
-#define E220_400M30S
+//#define E220_400M30S
 //#define E220_400M33S
+#define E22_400M33S
 
 #ifdef E220_400M30S
 #define SETTING_MAX_POWER 30
@@ -22,10 +35,10 @@
 #define SX126X_MAX_POWER 22
 #endif
 
-#ifdef E220_400M33S
+#ifdef E22_400M33S
 #define SETTING_MAX_POWER 33
-#define TX_GAIN_LORA 25
-#define SX126X_MAX_POWER 8
+#define TX_GAIN_LORA 12
+#define SX126X_MAX_POWER 21
 #endif
 
 #define USE_LLCC68

code/firmware-2.7.15.567b8ea/variants/esp32c3/diy/esp32c3_moonshine_mv/variant.h

@@ -23,6 +23,21 @@
 #define GPS_POWER_TOGGLE 1
 #define PIN_GPS_EN 12
 
+#define HAS_PCF8574_BUTTON
+#define PCF8574_ADDR 0x27
+#define PCF8574_INT_PIN 9
+
+#define PCF8574_BUTTON_MAP { \
+    INPUT_BROKER_SELECT,      /* P0: 确定 */ \
+    INPUT_BROKER_DOWN,        /* P1: 下 */ \
+    INPUT_BROKER_UP,          /* P2: 上 */ \
+    INPUT_BROKER_LEFT,        /* P3: 左 */ \
+    INPUT_BROKER_RIGHT,       /* P4: 右 */ \
+    INPUT_BROKER_SELECT,      /* P5: 确定 */ \
+    INPUT_BROKER_CANCEL,      /* P6: 取消 */ \
+    INPUT_BROKER_NONE,        /* P7: 未使用 */ \
+}
+
 
 #define BATTERY_PIN            2
 #define ADC_CHANNEL            ADC1_GPIO2_CHANNEL