develop
15
Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
  
|
4f0e2dde98 |
feat: add Ethernet OTA support for RP2350/W5500 boards (#10136)
* feat: add Raspberry Pi Pico 2 + W5500 + E22-900M30S variant Adds community variant for Raspberry Pi Pico 2 (RP2350, 4 MB flash) with external WIZnet W5500 Ethernet module and EBYTE E22-900M30S LoRa module (SX1262, 30 dBm PA, 868/915 MHz). Key details: - LoRa on SPI1: GP10/11/12/13 (SCK/MOSI/MISO/CS), RST=GP15, DIO1=GP14, BUSY=GP2, RXEN=GP3 (held HIGH via SX126X_ANT_SW) - W5500 on SPI0: GP16/17/18/19/20 (MISO/CS/SCK/MOSI/RST) - SX126X_DIO2_AS_RF_SWITCH: DIO2→TXEN bridge on module handles PA - SX126X_DIO3_TCXO_VOLTAGE 1.8: TCXO support via EBYTE_E22 flags - DHCP timeout reduced to 10 s to avoid blocking LoRa startup - GPS on UART1/Serial2: GP8 TX, GP9 RX - Reuses WIZNET_5500_EVB_PICO2 code paths for Ethernet init Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com> * pico2_w5500_e22: rename define and address review feedback Rename WIZNET_5500_EVB_PICO2 to PICO2_W5500_E22 so the variant-specific define matches the variant directory name and isn't confused with an on-board EVB SKU. Review fixes from PR #10135: - Gate the 10 s Ethernet DHCP timeout behind PICO2_W5500_E22 so other Ethernet builds keep the default 60 s behavior; apply the same timeout to reconnectETH() for consistency. - Drop the unused -D EBYTE_E22 flag; EBYTE_E22_900M30S already selects TX_GAIN_LORA / SX126X_MAX_POWER in src/configuration.h. - Rewrite "on-board W5500" comments to describe the external module. - Correct README TX_GAIN_LORA value (7, not 10) and drop the EBYTE_E22 row. * fix(pico2_w5500_e22): drop DEBUG_RP2040_PORT=Serial The arduino-pico framework hooks _write() when DEBUG_RP2040_PORT=Serial is set and dumps raw debug bytes onto USB CDC, corrupting any binary protobuf stream sent through StreamAPI (e.g. `meshtastic --port COMx`). The variant excludes BT and WiFi, so the primary client transport is Ethernet TCP via ethServerAPI — unaffected — but users who configure the node over USB serial would see protobuf decode failures from debug-byte interleaving. Removing the flag restores clean USB CDC. Debug output can still be enabled per-build by adding -D DEBUG_RP2040_PORT=Serial1 to redirect to UART0 instead of USB CDC. * feat: add Ethernet OTA support for RP2350/W5500 boards Adds over-the-air firmware update capability for RP2350-based boards with a WIZnet W5500 Ethernet module (e.g. pico2_w5500_e22). Protocol (MOTA): - SHA256 challenge-response authentication with a configurable PSK (override via USERPREFS_OTA_PSK; default key ships in source) - 12-byte header: magic "MOTA" + firmware size + CRC32 - Firmware received in 1 KB chunks, verified with CRC32, written via Updater (picoOTA), then device reboots to apply - Constant-time hash comparison prevents timing attacks on auth - 30s inactivity timeout + 5s cooldown after failed auth - Response codes 0x00-0x08 map 1:1 to OTAResponse enum Firmware side: - ethOTA.cpp / ethOTA.h: OTA TCP server on port 4243 - ethClient.cpp: wire initEthOTA/ethOTALoop into reconnect loop - main-rp2xx0.cpp: hardware watchdog (8s, paused during debug) - pico2_w5500_e22/platformio.ini: HAS_ETHERNET_OTA flag, filesystem_size bumped to 0.75m for OTA staging Host side: - bin/eth-ota-upload.py: Python uploader with progress and full result-code mapping (matches OTAResponse 0x00-0x08) * style(eth): clang-format ethOTA.cpp per repo .clang-format Reformat to the repo trunk clang-format config (IndentWidth 4, ColumnLimit 130). Resolves the Trunk Check 'Incorrect formatting' failure on PR #10136. Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com> --------- Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com> |
||
 
|
1cf6d7648f |
Leave src/platform out of the build filter by default (#10726)
* Leave src/platform out of the build filter by default, and only add back what each build needs. * typo fix Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> --------- Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> |
||
    Jonathan BennettGitHubBen MeadorsCopilotWesselcopilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>thebentern |
8267bb22bd |
Packet Signing via XEdDSA (#10478)
* Test commit for XEdDSA support * Update to Crypto lib in Meshtatic org * Generate a new node identity on key generation (#7628) * Generate a new node identity on key generation * Fixes * Fixes * Fixes * Messed up * Fixes * Update src/modules/AdminModule.cpp Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com> * Update src/mesh/NodeDB.cpp Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com> * Figured it out! * Cleanup * Update src/mesh/NodeDB.h Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com> * Update src/mesh/NodeDB.cpp Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com> * Update src/modules/AdminModule.cpp Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com> --------- Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com> * Update crypto commit hash * Some fixes for xeddsa pr (#9610) * fix: add null check for getMeshNode() in NodeInfoModule getMeshNode() can return nullptr for unknown nodes. Dereferencing without a check crashes the firmware when receiving NodeInfo from a node not yet in the database. * fix: enforce XEdDSA signature verification and prevent stripping Previously, failed signature verification still allowed the packet through, making signatures purely cosmetic. Now: - Failed verification drops the packet (DECODE_FAILURE) - Successfully verified nodes get HAS_XEDDSA_SIGNED bitfield set - Unsigned packets from previously-signing nodes are rejected - Log levels reduced from WARN/ERROR to DEBUG/WARN as appropriate * fix: include packet metadata in XEdDSA signature The signature now covers [fromNode | packetId | portnum | payload] instead of just the payload bytes. This prevents: - Replay attacks (different packetId fails verification) - Reattribution (different fromNode fails verification) - Portnum redirection (different portnum fails verification) Also adds a key initialization check to xeddsa_sign (returns false if XEdDSA keys are all zeros) and checks the return value in the encode path. * fix: handle existing key pair in AdminModule security config When a user provides both a valid private key and public key via admin config, the crypto engine's DH private key and owner public key were never loaded. DMs and XEdDSA signing would silently break. Add an else branch to load both keys into the crypto engine. * perf: cache Ed25519 public key conversion in xeddsa_verify curve_to_ed_pub() performs field element parsing, inversion, and multiplication on every call. Since packets from the same node tend to arrive in bursts, a single-entry cache avoids repeating this expensive conversion for consecutive packets from one sender. * fix: skip identity cleanup when node number is unchanged createNewIdentity() was called on every generateCryptoKeyPair(), including normal boots where the same key is regenerated. This caused unnecessary NodeDB writes and old-node cleanup logic to run when the node number hadn't actually changed. Also fixes only zeroing byte[0] of the old node's public key instead of clearing the entire array. * fix: replace hardcoded 120 with derived XEDDSA_SIGNATURE_SIZE constant The payload size check for XEdDSA signing used a magic number (120). Replace with a derivation from DATA_PAYLOAD_LEN and XEDDSA_SIGNATURE_SIZE so the limit adjusts automatically if constants change. This also increases the max signable payload from 120 to 169 bytes, which is still safe since the actual encoded size is checked after pb_encode. * fix: add const qualifiers to XEdDSA verify and curve_to_ed_pub inputs pubKey, payload, and signature parameters in xeddsa_verify are input-only and should not be modified. Same for curve_pubkey in curve_to_ed_pub. * chore: remove commented-out old Crypto dependency in portduino.ini * Leave out the admin module change for now --------- Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz> * trunk * protobuf re-update * Protobufs * Merge resolution fix * Put XEDDSA on the right bit * NodeDB update to new nodeInfoLite accessors, etc * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Potential fix for pull request finding Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com> * Refine unsigned packet rejection logic in Router (#10534) * use hardware random to fill the first 32 signature bytes with entropy prior to signing. * Add XEdDSA packet-signing policy tests and update dependencies for macos * Minor fixes * integrate XEdDSA support and update dependencies across multiple modules --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com> Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com> Co-authored-by: Wessel <github@weebl.me> Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com> Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com> |
||
|
|
ce7444c1a1 |
feat: add WIZnet W5500-EVB-Pico2 + E22P-868M30S variant (#10552)
* feat: add WIZnet W5500-EVB-Pico2 + E22P-868M30S variant Adds a community variant for the WIZnet W5500-EVB-Pico2 development board (https://docs.wiznet.io/Product/iEthernet/W5500/w5500-evb-pico2) paired with an external EBYTE E22P-868M30S LoRa module. This is the hardware twin of variants/rp2350/diy/pico2_w5500_e22 — same LoRa pinout, same W5500 pin mapping — and reuses its variant.h verbatim via `-I variants/rp2350/diy/pico2_w5500_e22`. No duplicated pinout file. Two differences vs pico2_w5500_e22 justify the separate env: 1. Board target: `wiznet_5500_evb_pico2` (2 MB flash) instead of `rpipico2` (4 MB flash). The WIZnet PCB ships with a smaller Q-SPI chip than a stock Pi Pico 2. Selecting the correct board makes the linker fail fast on overflow instead of producing a UF2 that gets silently truncated when flashed to the device. 2. W5500 PHY is integrated on the PCB (hard-wired SPI0 GP16-20) rather than supplied as an external module the user wires manually. The E22P-868M30S uses a single combined RFEN pin (LNA + PA enable) instead of the older E22-900M30S's split RXEN/TXEN pins. RFEN is held HIGH at all times via `SX126X_ANT_SW 3`; TX switching still uses the on-module DIO2 → TXEN bridge through `SX126X_DIO2_AS_RF_SWITCH`. Build verified: wiznet_5500_evb_pico2_e22p SUCCESS (RAM 19.2%, Flash 65.6% of 1.5 MB partition / 2 MB chip). * style(wiznet-evb-pico2-e22p): prettier-format README tables --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com> |
||
 Chloe BethelandGitHub
|
64e35908c9 | Add Xiao RP2040 and RP2350 variants (#10109) | ||
|
|
5b7a5b2c22 |
feat: add Raspberry Pi Pico 2 + W5500 + E22-900M30S variant (#10135)
* feat: add Raspberry Pi Pico 2 + W5500 + E22-900M30S variant Adds community variant for Raspberry Pi Pico 2 (RP2350, 4 MB flash) with external WIZnet W5500 Ethernet module and EBYTE E22-900M30S LoRa module (SX1262, 30 dBm PA, 868/915 MHz). Key details: - LoRa on SPI1: GP10/11/12/13 (SCK/MOSI/MISO/CS), RST=GP15, DIO1=GP14, BUSY=GP2, RXEN=GP3 (held HIGH via SX126X_ANT_SW) - W5500 on SPI0: GP16/17/18/19/20 (MISO/CS/SCK/MOSI/RST) - SX126X_DIO2_AS_RF_SWITCH: DIO2→TXEN bridge on module handles PA - SX126X_DIO3_TCXO_VOLTAGE 1.8: TCXO support via EBYTE_E22 flags - DHCP timeout reduced to 10 s to avoid blocking LoRa startup - GPS on UART1/Serial2: GP8 TX, GP9 RX - Reuses WIZNET_5500_EVB_PICO2 code paths for Ethernet init Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com> * pico2_w5500_e22: rename define and address review feedback Rename WIZNET_5500_EVB_PICO2 to PICO2_W5500_E22 so the variant-specific define matches the variant directory name and isn't confused with an on-board EVB SKU. Review fixes from PR #10135: - Gate the 10 s Ethernet DHCP timeout behind PICO2_W5500_E22 so other Ethernet builds keep the default 60 s behavior; apply the same timeout to reconnectETH() for consistency. - Drop the unused -D EBYTE_E22 flag; EBYTE_E22_900M30S already selects TX_GAIN_LORA / SX126X_MAX_POWER in src/configuration.h. - Rewrite "on-board W5500" comments to describe the external module. - Correct README TX_GAIN_LORA value (7, not 10) and drop the EBYTE_E22 row. * fix(pico2_w5500_e22): drop DEBUG_RP2040_PORT=Serial The arduino-pico framework hooks _write() when DEBUG_RP2040_PORT=Serial is set and dumps raw debug bytes onto USB CDC, corrupting any binary protobuf stream sent through StreamAPI (e.g. `meshtastic --port COMx`). The variant excludes BT and WiFi, so the primary client transport is Ethernet TCP via ethServerAPI — unaffected — but users who configure the node over USB serial would see protobuf decode failures from debug-byte interleaving. Removing the flag restores clean USB CDC. Debug output can still be enabled per-build by adding -D DEBUG_RP2040_PORT=Serial1 to redirect to UART0 instead of USB CDC. * style(pico2_w5500_e22): apply trunk fmt — fixes Trunk Check - variant.h: clang-format 16.0.3 (drop manual #define alignment) - README.md: prettier + add `text` language to fenced code blocks (markdownlint MD040) - wiring.svg: svgo optimization Resolves the Trunk Check Runner failure on this PR (3 unformatted files + 8 markdownlint issues). No functional changes. Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com> * refactor(pico2_w5500_e22): address review — move to rp2350/diy, generic guards Maintainer feedback from NomDeTom on PR #10135: - Move the variant from variants/rp2350/ to variants/rp2350/diy/ to distinguish DIY from prebuilt boards (matches the variants/*/diy/ pattern; still discovered via the existing variants/*/diy/*/platformio.ini glob in the root platformio.ini). - Replace the board-name macro PICO2_W5500_E22 in shared code with a generic capability macro USE_ARDUINO_ETHERNET, defined from variant.h. DebugConfiguration.h / ethServerAPI.h / ethClient.cpp no longer reference a board name. - Drop the architecture.h hook entirely: variant.h now defines PRIVATE_HW, which the existing `#elif defined(PRIVATE_HW)` branch already handles. No functional change. Build verified: pico2_w5500_e22 SUCCESS (RAM 19.2%, Flash 28.1%). Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com> * chore(pico2_w5500_e22): drop unoptimized wiring.svg to fix trunk fmt check --------- Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com> Co-authored-by: Ben Meadors <benmmeadors@gmail.com> |
||
|
|
4a1ff18f57 |
feat: add Nordic nRF54L15-DK variant (Zephyr + BLE + LoRa) (#10193)
* feat: add Nordic nRF54L15-DK variant (Zephyr + BLE + LoRa)
Adds a community hardware variant for the Nordic nRF54L15-DK (PCA10156)
with an external EBYTE E22-900M30S (SX1262) LoRa module. First Meshtastic
port running on the Zephyr RTOS; all other Nordic targets use the nRF5
SoftDevice stack.
Scope
-----
- New Zephyr-based platform layer under src/platform/nrf54l15/ providing
Arduino-compatible shims (Arduino.h, SPI, Wire, Print, Stream) over the
Zephyr APIs plus a LittleFS-backed InternalFileSystem on SPIM20.
- Bluetooth LE peripheral (NRF54L15Bluetooth.*) built on the Zephyr BT
host stack, exposing the Meshtastic GATT service with legacy
connectable advertising, just-works pairing, dynamic MTU exchange
(up to 247 bytes), and iOS connection-parameter tweaks.
- Variant directory variants/nrf54l15/nrf54l15dk/ with pin map for the
E22 module on connector J1, PlatformIO env (nrf54l15dk), Zephyr
DT overlay and a wiring README.
- Zephyr project config (zephyr/prj.conf + board overlay) tuned for
BT + LoRa: 16 KB main stack, 4 KB BT RX thread, RTT logging in
immediate mode, newlib-nano heap sized to leave room for the GATT
pools while still allowing ATT MTU=247.
- extra_scripts/nrf54l15_linker.py works around a PlatformIO + old Ninja
issue where Zephyr's two-pass linker script generation does not run
automatically; the post-script parses build.ninja and invokes the
gcc -E step directly before the final link.
- boards/nrf54l15dk.json board definition (PlatformIO needs it for the
DK; the Seeed platform only ships the XIAO variants).
- variants/rp2350/rp2350.ini excludes platform/nrf54l15/ from RP2350
build_src_filter so the shared platform tree does not leak between
targets.
- .gitignore: add nRF J-Link / RTT debug artifacts (flash.jlink,
rtt_*.txt).
Shared source changes
---------------------
- src/main.{cpp,h}, src/RedirectablePrint.cpp, src/FSCommon.{cpp,h},
src/mesh/{Channels,NodeDB,RadioLibInterface,MeshService,PhoneAPI}.cpp,
src/mesh/RadioLibInterface.h, src/modules/AdminModule.cpp: add small
guards / helpers so the Zephyr build compiles alongside the Arduino
targets. Behavior on existing boards is unchanged.
Hardware model
--------------
HW_VENDOR maps to meshtastic_HardwareModel_PRIVATE_HW until a dedicated
protobuf enum value is assigned upstream. The variant declares
custom_meshtastic_hw_model = 132 so the maintainers can wire the new
enum value through the protobufs repo after merge.
Hardware note
-------------
The E22-900M30S does not connect its DIO2 pin to TXEN internally — a
wire/solder bridge between DIO2 and TXEN on the module is required for
TX to work. Details and full pin map are in the variant README.
Validation
----------
Built clean against develop. On real hardware (April 2026) the port
passes end-to-end: iOS companion app pairs and connects, configuration
round-trip works, LoRa TX/RX reaches a canonical tbeam on the same mesh
channel, NodeDB updates propagate both ways, and traceroute completes.
* fix(nrf54l15): use atomic fs_rename instead of copy fallback
Zephyr LittleFS on nrf54l15 supports fs_rename natively, so route it
through the same atomic path as ESP32. The previous copyFile+remove
fallback truncated the destination before copying, leaving 0-byte files
if interrupted mid-write.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): expand storage_partition from 36KB to 700KB
LittleFS on the default 9-block (36KB) storage_partition ran out of
space during copy-on-write of config.proto, causing fs_write to return
ENOSPC and pb_encode to surface "io error" when saving configuration
via the mobile app.
Reclaim slot1_partition (the MCUboot secondary slot — unused since we
flash directly via J-Link) and grow storage_partition to span
0xb6000..0x165000 (~175 blocks).
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): drop USERPREFS_LORACONFIG_* so LoRa config stays mutable
NodeDB rewrites LoRa config from USERPREFS_LORACONFIG_* on every boot,
which prevented reconfiguration via the BLE/serial app. Drop the
variant-level defaults; users configure region and modem preset through
the app like every other variant.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): enforce MITM passkey pairing on GATT service
- Add MESH_PERM_READ/MESH_PERM_WRITE macros (READ_AUTHEN/WRITE_AUTHEN)
on all mesh service characteristics so clients must complete passkey
exchange before accessing fromNum/fromRadio/toRadio/logRadio.
- Wire FIXED_PIN mode to bt_passkey_set() so the device advertises a
known PIN (config.bluetooth.fixed_pin); RANDOM_PIN keeps default
per-pairing random passkey.
- Reduce BleDeferredThread HARD_WATCHDOG_MS from 3min to 1min.
- prj.conf: CONFIG_BT_SMP_ENFORCE_MITM=y, CONFIG_BT_FIXED_PASSKEY=y,
CONFIG_BT_SMP_SC_PAIR_ONLY=n (legacy fallback for clients that abort
SC pairing with reason 0x01 within 150ms).
* fix(nrf54l15): resolve develop-merge conflict + cppcheck warnings
The `Merge branch 'develop'` left two ~RadioLibInterface() declarations
in src/mesh/RadioLibInterface.h: the inline version added upstream by
PR #10254 (which independently applied the same UAF guard this PR was
carrying) and the out-of-line version this PR introduced. GCC rejects
the duplicate, breaking every platform build. Drop the out-of-line
declaration + definition; keep upstream's inline form.
Also silence the 13 cppcheck low warnings introduced by the new
nrf54l15 Arduino shim — Arduino's `String`/`SPISettings` API contract
relies on implicit single-arg constructors used pervasively by
existing Meshtastic code, so suppress `noExplicitConstructor` inline
with a comment instead of breaking the API. The few mechanical wins
(`const tmp[2]`, `const uint32_t *sp`) are applied directly.
* fmt: fix Trunk Check lint issues on nrf54l15-port
- extra_scripts/nrf54l15_linker.py: move regular imports above
Import("env") to silence E402, add trunk-ignore-all(F821) for the
PIO/SCons SConstruct injection (matches esp32_pre.py / nrf52_extra.py
convention)
- src/platform/nrf54l15/NRF54L15Bluetooth.cpp: clang-format 16.0.3
- boards/nrf54l15dk.json + variants/nrf54l15/nrf54l15dk/README.md:
prettier 3.8.3 (also resolves markdownlint MD060 on README tables)
No behavior change.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
* fix(nrf54l15): address Copilot review comments + correct clang-format style
Six review threads from the 2026-04-30 Copilot review:
- src/platform/nrf54l15/nrf54l15_main.cpp: validate PSP against the nRF54L15
SRAM range (0x20000000..0x20040000) and 4-byte alignment before walking the
faulting thread's stack, and clamp the walk so it never reads past the end
of RAM. Prevents a second fault inside the fatal handler when PSP is
corrupted (common in real faults).
- src/platform/nrf54l15/nrf54l15_arduino.cpp: gate the bring-up printk traces
in digitalWrite/digitalRead (CS/NRESET toggle log, BUSY-before-NRESET
snapshot, BUSY periodic timeline) behind a new -DNRF54L15_GPIO_DEBUG flag
that is off by default. The "dev NOT READY" message stays unconditional —
it indicates a genuine hardware/DTS misconfig.
- src/modules/AdminModule.cpp: don't mutate config.device.output_gpio_enabled
from handleGetConfig(). Reflect the live pin state in the response payload
only — a getter must not write back to disk-persisted state.
- src/platform/nrf54l15/InternalFileSystem.h: derive totalBytes() from
FIXED_PARTITION_SIZE(storage_partition) at compile time so it tracks the
DK overlay's ~700 KB partition instead of the stale 36 KB hard-coded value.
Updated the file header comment accordingly.
- extra_scripts/nrf54l15_linker.py: make _extract_gcc_command() handle the
POSIX Ninja COMMAND format (no `cmd.exe /C "..."` wrapper) in addition to
the Windows form, so the script doesn't hard-fail on Linux/macOS hosts.
- src/platform/nrf54l15/NRF54L15Bluetooth.cpp: clamp NO_PIN to RANDOM_PIN
with a one-shot LOG_WARN. The mesh GATT permissions are declared with
BT_GATT_PERM_*_AUTHEN and prj.conf sets CONFIG_BT_SMP_ENFORCE_MITM=y, so
NO_PIN with no auth callbacks would leave every characteristic returning
BT_ATT_ERR_AUTHENTICATION. Falling back to RANDOM_PIN keeps the link
usable instead of silently broken. Also re-formatted this file with the
project's .trunk/configs/.clang-format (Linux braces, 4-space indent,
130-col) — the previous lint-fix commit
|
||
|
Jonathan BennettandGitHub
|
2361776992 |
Rename LED_PIN to LED_POWER, move handling out of main to dedicated module (#9512)
* Rename LED_PIN to LED_POWER, move handling out of main to dedicated module * Misc * Remove errant endif |
||
 AustinandGitHub
|
176d8def48 | PlatformIO: Restructure networking_base for re-use (#8964) | ||
|
AustinandGitHub
|
917794ebab |
PIO: Remove useless inheritence (references extends env) (#8987)
Remove lib_deps section for all PlatformIO envs which are unneeded (only references the `extends` lib_deps, thus pointless) This makes the configs more concise and make future PIO variants/ libdeps audits easier. |
||
|
AustinandGitHub
|
024ac74f5c | rp2xx0: Update to arduino-pico 5.4.4 (#8979) | ||
|
Jonathan BennettandGitHub
|
41cbd77db3 | Move everything from /arch to /variant (#8831) | ||
|
AustinandGitHub
|
4f57a2e248 | Build RP2350 (Pi Pico 2) (#7441) | ||
|
AustinandGitHub
|
4f895f744b | Take control of our PRs! (#7445) | ||
|
AustinandGitHub
|
9313d04726 | RP2040/RP2350: Migrate variants to new structure (#7345) |