* fix(native): implement BinarySemaphorePosix with proper pthread synchronization
The BinarySemaphorePosix class (used on all Linux/portduino/native builds)
had stub implementations: give() was a no-op and take() just called
delay(msec) and returned false. This broke the cooperative thread scheduler
on native platforms — threads could not wake the main loop, radio RX
interrupts were missed, and telemetry never transmitted over the mesh.
Replace the stubs with a proper binary semaphore using pthread_mutex_t +
pthread_cond_t + bool signaled:
- take(msec): pthread_cond_timedwait with CLOCK_REALTIME timeout, consumes
signal atomically (binary semaphore semantics)
- give(): sets signaled=true, signals condition variable
- giveFromISR(): delegates to give(), sets pxHigherPriorityTaskWoken
Tested on Raspberry Pi 3 Model B (ARM64, Debian Bookworm) with Adafruit
LoRa Radio Bonnet (SX1276). Before fix: no radio TX/RX, no telemetry on
mesh. After fix: bidirectional LoRa, MQTT gateway, telemetry all working.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
* ARCH_PORTDUINO
* Refactor BinarySemaphorePosix header for ARCH_PORTDUINO
* Change preprocessor directive from ifndef to ifdef
* Gate new Semaphore code to Portduino and fix STM compilation
* Binary Semaphore Posix better error handling
---------
Co-authored-by: Claude Opus 4.6 <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* fix MESHTASTIC_EXCLUDE_SCREEN
* mesh-tab map constraints (2 MB PSRAM)
* point MUI commit to the related PR
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix TAG low‑voltage reboot hang after App configuration
* nRF52: Move low-VDD System OFF logic to variant hook
* Addressed review
* serialize SAADC access with shared mutex for VDD and battery reads
* raise LPCOMP wake threshold to ensure rising-edge wake
* Trunk fmt
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix(routing): prevent licensed users from rebroadcasting packets from unlicensed or unknown users
* fix(routing): prevent licensed users from rebroadcasting packets to or from unlicensed users
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The W5100S Ethernet chip has only 4 hardware sockets. On RAK4631
Ethernet gateways with syslog and NTP enabled, all 4 sockets were
permanently consumed (NTP UDP + Syslog UDP + TCP API listener + TCP
API client), leaving none for MQTT, DHCP lease renewal, or additional
TCP connections.
- NTP: Remove permanent timeClient.begin() at startup; NTPClient::update()
auto-initializes when needed. Add timeClient.end() after each query to
release the UDP socket immediately.
- Syslog: Remove socket allocation from Syslog::enable(). Open and close
the UDP socket on-demand in _sendLog() around each message send.
- MQTT: Fix socket leak in isValidConfig() where a successful test
connection was never closed (PubSubClient destructor does not call
disconnect). Add explicit pubSub->disconnect() before returning.
Made-with: Cursor
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
PlatformIO registry is (probably) rate limiting us. Mitigate by switching to GitHub source zips (based upon tags).
This change does not include any updates, simply swapping to a new download location.
* Fix TransmitHistory to improve epoch handling
* Enable epoch handling in unit tests
* Improve comments and test handling for epoch persistence in TransmitHistory
* Add boot-relative timestamp handling and unit tests for TransmitHistory
* loadFromDisk should handle legacy entries and clean up old v1 files after migration
* Revert "loadFromDisk should handle legacy entries and clean up old v1 files after migration"
This reverts commit eb7e5c7acf.
* Add NodeInfoModule integration for RTC quality changes and trigger immediate checks
* Update test conditions for RTC quality checks
We cache and dedupe our dependencies, referring to them with multiple methods/urls is just noise.
```
lewisxhe/XPowersLib@0.3.3
lewisxhe/SensorLib@0.3.4
```
This does *not* include any updates, just a cleanup.
The touch-to-backlight feature was gated behind TTGO_T_ECHO_PLUS, but
the regular T-Echo has the same backlight pin (PIN_EINK_EN, P1.11).
This changes the guard to use PIN_EINK_EN only, so any device with an
e-ink backlight pin gets the feature.
Fixes#7630
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix issue 9792, decode packet for TR test
* Fix 9792: Assure packet id decoded for TR test
* Potential fix for pull request finding
Log improvement for failure to decode packet.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* trunk fmt
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* fix: MQTT settings silently fail to persist when broker is unreachable
isValidConfig() was testing broker connectivity via connectPubSub() as
part of config validation. When the broker was unreachable (network not
ready, DNS failure, server down), the function returned false, causing
AdminModule to skip saving settings entirely — silently.
This removes the connectivity test from isValidConfig(), which now only
validates configuration correctness (TLS support, default server port).
Connectivity is handled by the MQTT module's existing reconnect loop.
Fixes#9107
* Add client warning notification when MQTT broker is unreachable
Per maintainer feedback: instead of silently saving when the broker
can't be reached, send a WARNING notification to the client saying
"MQTT settings saved, but could not reach the MQTT server."
Settings still always persist regardless of connectivity — the core
fix from the previous commit is preserved. The notification is purely
advisory so users know to double-check their server address and
credentials if the connection test fails.
When the network is not available at all, the connectivity check is
skipped entirely with a log message.
* Address Copilot review feedback
- Fix warning message wording: "Settings will be saved" instead of
"Settings saved" (notification fires before AdminModule persists)
- Add null check on clientNotificationPool.allocZeroed() to prevent
crash if pool is exhausted (matches AdminModule::sendWarning pattern)
- Fix test comments to accurately describe conditional connectivity
check behavior and IS_RUNNING_TESTS compile-out
* Remove connectivity check from isValidConfig entirely
Reverts the advisory connectivity check added in the previous commit.
While the intent was to warn users about unreachable brokers,
connectPubSub() mutates the isConnected state of the running MQTT
module and performs synchronous network operations that can block
the config-save path.
The cleanest approach: isValidConfig() validates config correctness
only (TLS support, default server port). The MQTT reconnect loop
handles connectivity after settings are persisted and the device
reboots. If the broker is unreachable, the user will see it in the
MQTT connection status — no special notification needed.
This returns to the simpler design from the first commit, which was
tested on hardware and confirmed working.
* Use lightweight TCP check instead of connectPubSub for validation
Per maintainer feedback: users need connectivity feedback, but
connectPubSub() mutates the module's isConnected state.
This uses a standalone MQTTClient TCP connection test that:
- Checks if the server IP/port is reachable
- Sends a WARNING notification if unreachable
- Does NOT establish an MQTT session or mutate any module state
- Does NOT block saving — isValidConfig always returns true
The TCP test client is created locally, used, and destroyed within
the function scope. No side effects on the running MQTT module.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix for preserving pki_encrypted and public_key when relaying UDP multicast packets to radio.
PKI DMs sent over UDP multicast had their pki_encrypted flag and public_key fields explicitly cleared before being forwarded to the LoRa radio. This caused the receiving node to treat the packet as a channel-encrypted message it couldn't decrypt, silently dropping it.
The MQTT ingress path correctly preserves these fields. The UDP multicast ingress path should behave the same way.
* Zeroize MeshPacket before decoding
Zeroize MeshPacket before decoding to prevent data leakage.
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix RAK4631 Ethernet gateway API connection loss after W5100S brownout
PoE power instability can brownout the W5100S while the nRF52 MCU keeps
running, causing all chip registers (MAC, IP, sockets) to revert to
defaults. The firmware had no mechanism to detect or recover from this.
Changes:
- Detect W5100S chip reset by periodically verifying MAC address register
in reconnectETH(); on mismatch, perform full hardware reset and
re-initialize Ethernet interface and services
- Add deInitApiServer() for clean API server teardown during recovery
- Add ~APIServerPort destructor to prevent memory leaks
- Switch nRF52 from EthernetServer::available() to accept() to prevent
the same connected client from being repeatedly re-reported
- Add proactive dead-connection cleanup in APIServerPort::runOnce()
- Add 15-minute TCP idle timeout to close half-open connections that
consume limited W5100S hardware sockets
Fixesmeshtastic/firmware#6970
Made-with: Cursor
* Log actual elapsed idle time instead of constant timeout value
Address Copilot review comment: log millis() - lastContactMsec to show
the real time since last client activity, rather than always logging the
TCP_IDLE_TIMEOUT_MS constant.
Made-with: Cursor
* Update src/mesh/api/ServerAPI.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Stop UDP multicast handler during W5100S brownout recovery
After a W5100S chip brownout, the udpHandler isRunning flag stays
true while the underlying socket is dead. Without calling stop(),
the subsequent start() no-ops and multicast is silently broken
after recovery.
Made-with: Cursor
* Address Copilot review: recovery flags and timeout constant
Move ethStartupComplete and ntp_renew reset to immediately after
service teardown, before Ethernet.begin(). Previously, if DHCP
failed the early return left ethStartupComplete=true, preventing
service re-initialization on subsequent retries.
Replace #define TCP_IDLE_TIMEOUT_MS with static constexpr uint32_t
for type safety and better C++ practice.
Made-with: Cursor
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix NodeInfo suppression logic to ensure suppression only applies to external requests
* Ensure NodeInfo reply suppression logic to only apply for external requests which are actually nodeinfo packets
Problem:
- Inserting a µSD card causes RadioLib to hit a critical error and reboot
- Device enters a boot loop as the SD card remains inserted
Reproduction:
- Insert a µSD card and power on
- RadioLib reports a critical error on boot
- Device reboots, repeating indefinitely
Root cause:
- On T-Lora Pager, SX1262 and the µSD slot share the same physical SPI bus
(same SCK/MOSI/MISO pins, differentiated only by CS)
- SDCARD_USE_SPI1 is intended for boards where SD is on a separate SPI bus;
it initializes a second ESP32 SPI peripheral (SPI3) for SD
- SPI2 is already driving those same pins for LoRa, so both controllers
simultaneously drive the same GPIO lines, causing bus contention
Fix:
- Remove SDCARD_USE_SPI1 so both devices share a single SPI peripheral (SPI2),
with CS pins providing device selection as intended
- Tested on a custom fork of device-ui; LoRa and SD card map tiles both work
correctly with an SD card inserted
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Enable pre-hop drop handling by default
* Remove early break if BME/DPS sensors are not detected at the BME address
* revert sneaky change
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The Seeed Xiao S3 Kit's default GPS is an L76K which operates at 9600 baud, so when this variant was defined that baud rate was specified.
However, this is a development board and it is expected that users can attach their own devices. This includes GPS, which may operate at a different baud rate. The current fixed baud rate prevents this, so this patch removes that setting.
This will revert to the regular automatic probe method. This will successfully detect the L76K as before (the same speed as before since 9600 baud is the first baud rate checked), but also allow other GPSes at other baud rates to be detected.
Thanks to @ScarpMarc for the report
Fixes https://github.com/meshtastic/firmware/issues/9373#issuecomment-3774802763
Fixes this build error:
<command-line>: error: expected unqualified-id before '-' token
/home/<snip>/.platformio/packages/framework-arduinoespressif32/variants/esp32s3/pins_arduino.h:15:22: note: in expansion of macro 'LED_BUILTIN'
15 | static const uint8_t LED_BUILTIN = SOC_GPIO_PIN_COUNT + PIN_RGB_LED;
| ^~~~~~~~~~~
More info: https://github.com/meshtastic/firmware/pull/9122#issuecomment-4028263894
The fix is consistent with variants/esp32s3/heltec_v3/platformio.ini
This commit is intentionally on the develop branch, because it's harmless to
develop branch, and makes us more ready for pioarduino when the time comes.
Heltec v4 introduced in: https://github.com/meshtastic/firmware/pull/7845
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add C++17 support
* Add C++17 runtime probes and update build configurations for STM32 and Portduino
* Remove unflags
* Update C++ standard flags across the platforms
* Convert a couple of instances to structured bindings
* NRF52 platform.txt to add C++17 support
* Still need the unflags apparently
* Remove C++17 runtime probe tests from test_main.cpp
* Reconfigured doesnt need a nodiscard
* Remove nodiscard attribute from init() method in RadioInterface
* Remove mbedtls/error.h from build flags
Removed include directive for mbedtls/error.h from build flags.
* Fix IRAM overflow
* Fix IRAM overflow
* Add build flag to exclude MQTT from rak11200
* Update C++ standard from gnu17 to gnu++17
* Update ESP8266Audio dependency to Meshtastic fork for compatibility
* Update ESP8266Audio dependency to Meshtastic fork for compatibility across multiple platformio.ini files
Addendum to PR #9791
The sourcedebs cannot currently be built offline >30 days after release. Extend the cache-expiry-mangling hack to sourcedeb packaging.
socketSendUDP() calls yield() while waiting for SEND_OK, allowing the
cooperative scheduler to run AsyncUDP::runOnce(). When runOnce() calls
parsePacket() on the same socket during an active send, the multicast
loopback packet arriving from the switch produces a garbled 8-byte RX
header (wrong source IP, wrong payload length), leading to protobuf
decode errors in UdpMulticastHandler.
Add a volatile isSending flag that writeTo() sets around endPacket()
(the only yield point). runOnce() checks this flag and skips
parsePacket() while a send is in progress. Loopback packets stay
buffered in the W5100S RX buffer and are read cleanly on the next
poll cycle.
Also propagate writeTo() return value in UdpMulticastHandler::onSend()
instead of unconditionally returning true.
Made-with: Cursor
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Nodelist cleanup
* Trunk fix
* getTextWidth cleanup
Updated the lambda to cache width in textW and reuse it instead of repeatedly calling getTextWidth(text) for unchanged text.
* Putting back hopAway ==0 condition as mentioned relayed signal is missleading
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update Heltec Tracker v2 to version KCT8103L.
* Fixed the issue of inaccurate comments.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
P0.04 is a digital power-enable pin for the NTC/LUX sensors, not an ADC
input. The old code was calling analogRead() on a floating GPIO that
happened to read ~mid-rail, coincidentally producing reasonable
temperature values.
- Rename T1000X_VCC_PIN to T1000X_SENSOR_EN_PIN and drive it HIGH in
initVariant() for both T1000-E and T1000-S variants
- Read BATTERY_PIN (with ADC_MULTIPLIER) instead, clamped to the 3.0V
LDO output (NTC_REF_VCC) for the NTC resistance calculation
* Cardputer Kit
BMI270 WIP
* BMI270 support
* verify that the number of bytes read matches the requested length
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* trunk'd
* remove excessive logging
* Kick the screen when unsleeping
* Update the st7789 library, and enable displayon and displayoff
* Battery detection
* Default to arrow keys and enter, while in menus.
* Enable Backlight control
* Update src/detect/ScanI2CTwoWire.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* updateState method now accepts shouldRequestFocus parameter for better maintainability
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add Portduino Enable pins
* Add hat plus custom fields
* Punt on the GPIO device detection for now
* Simplify TX_GAIN_LORA for RAK13302
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
This fixes builds in very clean environment with default build target (e.g.
-t buildfs *not* explicitly specified).
Tested: pio run -e heltec-v3
Fixes#9035
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Adds ROUTER_LATE and CLIENT_BASE to preferred rebroadcaster check
(skip unsolicited NodeInfo) and prevents ROUTER_LATE from setting
rebroadcast mode to NONE, which would silently break relaying.
ROUTER_LATE is an infrastructure relay that should use the same power
assumptions, interval defaults, and LoRa wake behavior as ROUTER.
Without this, ROUTER_LATE uses client-class defaults and will not
wake on LoRa activity from deep sleep, making it a broken relay.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER_LATE already has high base intervals and should not be further
scaled by congestion. TAK_TRACKER is a tracker variant that should
skip congestion scaling like TRACKER does.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER and ROUTER_LATE should not accumulate favorites by sending DMs.
Also replaces magic number 12 with meshtastic_Config_DeviceConfig_Role_CLIENT_BASE.
ROUTER_LATE should be treated as an impolite telemetry role like
ROUTER, responding to multi-hop broadcast requests and using
aggressive send timing without channel utilization checks.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
ROUTER_LATE now preserves node_info_broadcast_secs during factory
reset and auto-enables Store & Forward server mode, matching ROUTER
infrastructure behavior.
* refactor: update throttling factor calculation and add unit tests for scaling behavior
* refactor: adjust throttling factor calculation for improved accuracy in different configurations
* Update src/mesh/Default.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/mesh/Default.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* refactor: enhance throttling factor calculation and introduce pow_of_2 utility function
* refactor: improve expected ms calculation in unit tests for Default::getConfiguredOrDefaultMsScaled
* refactor: improve scaling logic for routers and sensors in computeExpectedMs function
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Improve resource cleanup on connection close
* Copilot had some good feedback. Let's just make the api a unique pointer
* Update src/mesh/api/ServerAPI.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Copilot stupidly suggesting we call protected methods
* Gotta do it in the superclasses as well
* Fix moar
* Refactor MQTT unit test to ensure proper subscription handling and clear side effects
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Add ESP32 Power Management lessons learned document
Documents our experimentation with ESP-IDF DFS and why it doesn't
work well for Meshtastic (RTOS locks, BLE locks, USB issues).
Proposes simpler alternative: manual setCpuFrequencyMhz() control
with explicit triggers for when to go fast vs slow.
* Added a lambda function to clear startup output in the MQTT unit test to ensure a clean state before and after the MQTT subscription process.
getByIndex allocates memory and returns dummy channel whenever
chIndex validation fails. Comment implies this may happen
when malformed packet is received. The fix changes implementation
so static dummyChannel is returned in such case.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* enhance tx queue priority management
In busy environments, especially for ROUTER_LATE role, tx queue
fills very quickly. Delayed packets became late but new packets
to be retransmitted won't be put into the tx queue as old ones
stay there for a very long time (even a minute or more). This change
makes meshtastic prioritize new packets over late packets from tx queue
and allows to remove late packet from back of tx queue when there
is no space for a new one.
* apply copilot recommendation for cast
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Don't launch canned message when waking screen or silencing notification
* Add screen ifdefs
* Get the #if right
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix(MQTT): First MapReport does not get sent
Throttle::isWithinTimespanMs(last_report_to_map, map_publish_interval_msecs) is
used to maintain the map reporting interval, but because last_report_to_map has
an initial value of 0, the map report routine does not start until the system
millis() time has passed map_publish_interval_msecs.
Fix this by adding a check that last_report_to_map is not 0.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* feat(MQTT): Send MapReporting immediately upon location fix
Do not update last_report_to_map when Map Report is attempted without a valid
location, as this results in waiting up to an hour (or configured Map Report
interval).
That usually happens because most nodes do not keep GPS warm, so GPS usually
locks after the first attempt at Map Report.
This change also results in the log WARNing message getting spammed until a
location is obtained, so remove the message for now.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* feat(MQTT): Throttled warning when position is not available for MapReport
Signed-off-by: Andrew Yong <me@ndoo.sg>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Add transmit history for throttling that persists between reboots
* Fix RAK long press detection to prevent phantom shutdowns from floating pins
* Update test/test_transmit_history/test_main.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Test fixes and placeholder for content handler tests
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Change file name from BLEDfuScure.cpp to BLEDfuSecure.cpp. Fix filenames
in documentation.
Signed-off-by: Koko <github@kokosoftware.pl>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add GPIO_DETECT_PA portduino config, and support 13302 detection with it.
* Tweak PA detect gpio to use pinMapping
* minor yaml output fixes
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Align telemetry broadcast want_response behavior with traceroute
* Fixes
* Reduce side-effects by making the telemetry modules handle the ignorerequest
* Remove unnecessary ignoreRequest flag
* Try inheriting from MeshModule
* Add exclusion for sensor/router roles and add base telem module
* Implement 'agc' reset for SX126x chip family
There's no actual agc on SX126x chips but you can reset the analog
registers by doing a warm sleep & running calibration.
* Address PR comments & implement for LR11x0 too
* calibrate for configured frequency band
* Gate LR11X0_AGC_RESET
* Apply SX1262 register 0x8B5 patch for improved GC1109 RX sensitivity
Sets the LSB of undocumented SX1262 register 0x8B5 on Heltec V4 and
Wireless Tracker V2 boards with the GC1109 FEM. This patch was
recommended by Heltec/Semtech and tested in MeshCore PR #1398, where
it significantly reduced packet loss on the Heltec V4.
* Use higher level function
* Add .venv/ to .gitignore
* Reduce maximum concurrent HTTPS connections to save memory
* Add heap check and limit connections to prevent HTTPS connection related crashes
* Use Throttle::isWithinTimespanMs for overflow-safe heap warning throttle
* Update src/mesh/http/WebServer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix double-free heap corruption and parser leak in web server handlers
- Remove double-free in handleFsBrowseStatic, handleNodes, handleScanNetworks:
JSONValue(const JSONArray&) shallow-copies pointers, so delete value already
recursively frees all elements. The explicit cleanup loops were deleting the
same pointers a second time, corrupting the ESP32 heap allocator metadata.
This is the likely root cause of #8827 (SSL setup failures after uptime).
- Fix memory leak in handleFormUpload: two early-return paths were missing
delete parser.
- Remove unused global HTTPClient httpClient and its includes.
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Hold GC1109 PA_POWER and PA_EN during deep sleep for LNA RX wake
Use rtc_gpio_hold_en to latch PA_POWER (LDO) and PA_EN (CSD) HIGH
during deep sleep so the GC1109 LNA remains powered for wake-on-packet
RX. Previously these pins used weak pull-ups which could lose state.
On deep sleep wake, skip these pins in the blanket RTC hold release and
instead release them in SX126xInterface::init() after GPIO registers are
set HIGH first, avoiding a power glitch on the GC1109.
Trade-off: ~6.5mA additional deep sleep current for significantly
improved wake-on-packet RX sensitivity (~17dB).
Reference: https://github.com/meshcore-dev/MeshCore/pull/1600
* Add LDO startup delay before GC1109 chip enable
TLV75733P LDO has ~550us startup time (datasheet tSTR). On cold boot,
wait 1ms for VBAT to stabilise before driving CSD/CPS, per GC1109
power-on sequence requirement. On deep sleep wake the LDO is held on
via RTC latch so no delay is needed.
* onNavUp() sets the menu cursor to the last item if not shown
* skip headers when showing the menu cursor in onNavUp() and onNavDown()
* skip headers when showing the menu cursor in onButtonShortPress()
* brace cursor incrementing
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
* Don't ever define PIN_LED or BLE_LED_INVERTED (#9494)
* Don't ever define PIN_LED
* Deprecate BLE_LED_INVERTED
* Add StatusMessage module and config overrides (#9351)
* Add StatusMessage module and config overrides
* Trunk
* Don't reboot node simply for a StatusMessage config update
* Missed in reviews - fixing send bubble (#9505)
* Prefer EXT_PWR_DETECT pin over chargingVolt to detect power unplugged (#9511)
* Make sure we always return a value in NodeDB::restorePreferences() (#9516)
In case FScom is not defined there is no return statement. This
moves the return outside of the ifdef to make sure a defined
value is returned.
* Inkhud battery icon improvements. (#9513)
* Inkhud battery icon improvements.
Fixes the battery icon draining from the flat side towards the bump, which is backwards from general design language seen on most devices
By request of kr0n05_ on discord, adds the ability to mirror the battery icon which fixes that issue in another way, and is also a common design seen on other devices.
* Remove option for icon mirroring
* Add border + dither to battery to prevent font overlap
* Fix trunk format
* Code cleanup, courtesy of Xaositek.
* Add reply bot module with DM-only responses and rate limiting (#9456)
* Implement Meshtastic reply bot module with ping and status features
Adds a reply bot module that listens for /ping, /hello, and /test commands received via direct messages or broadcasts on the primary channel. The module always replies via direct message to the sender only, reporting hop count, RSSI, and SNR. Per-sender cooldowns are enforced to reduce network spam, and the module can be excluded at build time via a compile flag. Updates include the new module source files and required build configuration changes.
* Update ReplyBotModule.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/ReplyBotModule.h
Match the existing MESHTASTIC_EXCLUDE_* guard pattern so the module is excluded by default.
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/ReplyBotModule.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Tidying up
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* HotFix for ReplyBot - Modules.cpp included and moved configuration.h (#9532)
* Undefine LED_BUILTIN (#9531)
Keep variant in sync with
https://github.com/meshtastic/firmware/commit/df40085
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add agc reset attempt (#8163)
* Add agc reset attempt
* Add radioLibInterface include
* Trunk
* AGC reset don't crash, don't naively call
* Update src/main.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Use Throttle function
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Remove unused hmx variable (#9529)
The variable is not used at all in the function, remove it to
silence the compiler warning.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Rename LED_PIN to LED_POWER, move handling out of main to dedicated module (#9512)
* Rename LED_PIN to LED_POWER, move handling out of main to dedicated module
* Misc
* Remove errant endif
* Fix hop_limit upgrade detection (#9550)
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* meshtasticd: Fix install on Fedora 43 (#9556)
* RPM: Include meshtasticd-start.sh (#9561)
* Add Slash Key to VirtualKeyboard (#9563)
Addition of ? and / to the virtual Keyboard via short and long press
* Add support for CW2015 LiPo battery fuel gauge (#9564)
* Add support for CW2015 LiPo battery fuel gauge
* Address Copilot's concerns, minor fixups
* Make LED_POWER blip even in critical battery (#9545)
* Enable FORTIFY and SP for native builds (#9537)
* Enable FORITFY and NX for native builds
meshtasticd does have an executable stack and is not built with fortify, which makes exploitation of memory corruption bugs easier than it has to be. This enables fortify and a non-executable stack.
This gives the following improvements on Debian Trixie:
$ checksec --file=./.pio/build/native/meshtasticd
RELRO STACK CANARY NX PIE RPATH RUNPATH Symbols FORTIFY Fortified Fortifiable FILE
Partial RELRO No canary found NX enabled PIE enabled No RPATH No RUNPATH 13516 Symbols No 0 17 ./.pio/build/native/meshtasticd
$ checksec --file=./.pio/build/native/meshtasticd
RELRO STACK CANARY NX PIE RPATH RUNPATH Symbols FORTIFY Fortified Fortifiable FILE
Partial RELRO Canary found NX enabled PIE enabled No RPATH No RUNPATH 13519 Symbols Yes 12 20 ./.pio/build/native/meshtasticd
Tested with --sim mode I do not get any crashes or similar.
* Enable FORTIFY and NX for native builds
meshtasticd does have an executable stack and is not built with fortify, which makes exploitation of memory corruption bugs easier than it has to be. This enables fortify and a non-executable stack.
This gives the following improvements on Debian Trixie:
$ checksec --file=./.pio/build/native/meshtasticd
RELRO STACK CANARY NX PIE RPATH RUNPATH Symbols FORTIFY Fortified Fortifiable FILE
Partial RELRO No canary found NX enabled PIE enabled No RPATH No RUNPATH 13516 Symbols No 0 17 ./.pio/build/native/meshtasticd
$ checksec --file=./.pio/build/native/meshtasticd
RELRO STACK CANARY NX PIE RPATH RUNPATH Symbols FORTIFY Fortified Fortifiable FILE
Partial RELRO Canary found NX enabled PIE enabled No RPATH No RUNPATH 13519 Symbols Yes 12 20 ./.pio/build/native/meshtasticd
Tested with --sim mode I do not get any crashes or similar.
* Enable FORTIFY and SP for native builds
meshtasticd does have a stack canaries and is not built with fortify, which makes exploitation of memory corruption bugs easier than it has to be. This enables fortify and stack canaries.
This gives the following improvements on Debian Trixie:
$ checksec --file=./.pio/build/native/meshtasticd
RELRO STACK CANARY NX PIE RPATH RUNPATH Symbols FORTIFY Fortified Fortifiable FILE
Partial RELRO No canary found NX enabled PIE enabled No RPATH No RUNPATH 13516 Symbols No 0 17 ./.pio/build/native/meshtasticd
$ checksec --file=./.pio/build/native/meshtasticd
RELRO STACK CANARY NX PIE RPATH RUNPATH Symbols FORTIFY Fortified Fortifiable FILE
Partial RELRO Canary found NX enabled PIE enabled No RPATH No RUNPATH 13519 Symbols Yes 12 20 ./.pio/build/native/meshtasticd
Tested with --sim mode I do not get any crashes or similar.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update built-in documentation for current method of implementation (#9592)
* Refactor logging in ProtobufModule to ensure message details are logged after successful decoding (#9536)
* Automated version bumps (#9604)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Add missing openocd_target to custom nrf52 boards (#9603)
This stops platformio complaining about `Missing target configuration for me25ls01-4y10td` etc when trying to flash with nrfutil.
* Add sdl libs for native builds (#9595)
* Add sdl libs for native builds
* Alpine try again
* fix some random compiler warnings (#9596)
* Modify the dependency library of v4-tft (#9507)
* BaseUI: Favorite Screen Signal Quality improvement (#9566)
* Favorite Signal Quality improvement
* Show Voltage if node shares it.
* Trunk Fix
* Change Favorite tittle to encase name with Asterisks
* Add Pluggin In condition for Battery Line
* Adjust getUptimeStr Prefixes
* Create isAPIConnected for SharedCommon usage
* Correct leftSideSpacing to account for isAPIConnected
---------
Co-authored-by: Jason P <applewiz@mac.com>
* ExternalNotification and StatusLED now call AmbientLighting to update… (#9554)
* ExternalNotification and StatusLED now call AmbientLighting to update RGB LEDs. Add optional heartbeat
* Don't overwrite RGB state if heartbeat is disabled.
* Use the right define
* Remove another .h and make rgb static
* move rgb objects into AmbientLighting class
* Straighten out AmbientLighting Thread object
* Use %f for floats
* Fixes on SCD4X admin comands (#9607)
* Fixes on SCD4X admin comands
* Minor fix in logs for SEN5X
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* feat/add sfa30 (#9372)
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Initial implementation for SFA30Sensor
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Add functional SCD4X
* Fix screen frame for CO2
* Add admin commands to SCD4X class
* Add further admin commands and fixes.
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 0847969201.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Small reordering in PMS class for consistency
* If one sensor fails, AQ telemetry still reports data
* Small formatting fix
* Add SEN5X to AQI in ScanI2C
* SCD4X now part of AQ module with template list
* Fixes difference between idle and sleep
* In LowPower, sleep is disabled
* Requires testing for I2C clock comms for commands
* Remove unnecessary import
* Add co2 to serialized AQ metrics
* Add SFA30 with new sensor template in AQ module
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Fix uninitMemberVars
* Fix import error for SCD4X
* Fix I2CClock logic
* Fix not reclocking back to 700000Hz
* Fix multiple sensors being read simultaneously
* The logic in AQ module is different to the one in EnvironmentTelemetryModule. In Env module, if any sensor fails to getMetrics, no valid flag for the module. This prevents other sensors to report data.
* Fix pending clock change in PMSA003
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Make sure clock is always set to needed value
* Fix returns
* Fix trunk
* Fix on condition in reclock
* Fix trunk
* Final SFA30 class implementation
* Add HCHO to screen and improve logs
* Add metrics to mesh packet serializer
* Minor fixes in logs
* OCD tidy up of logs
* Fix sleep function
* Remove old I2C_CLOCK_SPEED code
---------
Co-authored-by: nikl <nikl174@mailbox.org>
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Log rxBad PacketHeaders with more info (id, relay_node) like printPacket, so we can try to match RX errors to other packets in the logs. (#9614)
* Exclude status message module
* fix: zero entire public key array instead of only first byte (#9619)
* Update protobufs (#9621)
* Xiao NRF - define suitable i2c pins for the sub-variants (#8866)
Co-authored-by: Christian Walther <cwalther@gmx.ch>
* Update src/detect/ScanI2C.cpp
Co-authored-by: Wessel <wessel@weebl.me>
* Update src/modules/Telemetry/Sensor/SFA30Sensor.cpp
Co-authored-by: Wessel <wessel@weebl.me>
* Update src/modules/Telemetry/Sensor/SFA30Sensor.cpp
Co-authored-by: Wessel <wessel@weebl.me>
* Update src/modules/Telemetry/Sensor/SFA30Sensor.cpp
Co-authored-by: Wessel <wessel@weebl.me>
* Update src/mesh/NodeDB.cpp
Co-authored-by: Wessel <wessel@weebl.me>
* convert GPS global and some new in gps.cpp to unique_ptr (#9628)
Trying this to see if anything bad happen if I were to replace most raw pointers with unique_ptr.
I didn't used std::make_unique since it is only supported in C++14 and onwards but until we update esp32 to arduino 3.x the ESP32 xtensa chips use a C++11 std.
* replace delete in RedirectablePrint.cpp with std::unique_ptr (#9642)
Is part of the unique_ptr modernization effort.
* replace delete in EInkDynamicDisplay.{cpp,h} with std::unique_ptr (#9643)
Is part of the unique_ptr modernization effort.
* Undefine LED_BUILTIN for Heltec v2 variant (#9647)
* Undefine LED_BUILTIN for Heltec v2 variant
* Undefine LED_BUILTIN for Heltec v2.1 variant
---------
Co-authored-by: Jorropo <jorropo.pgm@gmail.com>
* replace delete in RadioInterface.cpp with std::unique_ptr (#9645)
Is part of the unique_ptr modernization effort.
* fix typo in PIN_GPS_SWITCH (#9648)
Wasn't caught by CI.
* replace delete in CryptoEngine.{cpp,h} with std::unique_ptr (#9649)
Is part of the unique_ptr modernization effort.
* workaround NCP5623 and LP5562 I2C builds (#9652)
Theses two appear to be buggy on r1-neo and nomadstar meteor pro, they rely on Wire.h being included previously to their import.
Idk why other platforms using the same smart LEDs are working while theses ones don't.
This should make CI green on the dev branch.
* replace delete in AudioThread.h with std::unique_ptr (#9651)
Is part of the unique_ptr modernization effort.
* Add USB_MODE=1 for Station G2 (#9660)
* InkHUD: Favorite Map Applet (#9654)
* fix a lot of low level cppcheck warnings (#9623)
* simplify the observer pattern, since all the called functions are const getters.
* use arduino macro over std: for numerical values and refactor local variables in drawScrollbar()
* oh, so Cppcheck actually complained about const pointers not being const.
* slowly getting out of ifdef hell
* fix inkHUD warnings as well
* last 2 check warnings
* git checks should fail on low defects from now on
* Feat/add scd30 (#9609)
* Merge develop into SCD30
* Add SCD30 class
* Fix logging and admin commands
* Minor cleanup and logging improvements
* Minor formatting issue
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Improvements on setTemperature
* Fix casting float-uint16_t
* Pass 100 for resetting temperature offset
* Fix issues pointed out by copilot
* Add quick reboot to set interval quicker on scd30
* Change saveState to only happen after boot and minor log changes
* Fix missing semicolon in one shot mode log
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix: respect DontMqttMeBro flag regardless of channel PSK (#9626)
The previous PSK check was broken from its introduction in #4643 —
memcmp was used in boolean context without comparing to 0, inverting
the condition. Since no one noticed for over a year, the PSK-based
filtering provided no practical value. Simplifying to always respect
the sender's preference is both more correct and easier to reason about.
* our firmware action is too clever
Update pio_target and add pio_opts for checks.
* fix detection of SCD30 by checking if the size of the return from a 2 byte register read is correct (#9664)
* fix detection of SCD30 by checking if thee size of the return from a 2 byte register read is correct
fix signedness warning in PMSA003 sensor code.
* Add alternate path for LPS22HB
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* check EndTransmission for errors and compare returned length to expected value
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* #9623 resolved a local shadow of next_key by converting it to int. (#9665)
* zip a few gitrefs down (#9672)
* InkHUD: Allow non-system applets to subscribe to input events (#9514)
* Allow inkhud user applets to consume inputs with opt-in system
Adds a way for applets to subscribe to input events while keeping it off
by default to preserve compatibility and expected behaviours. Adds
example for use as well.
* Add check for nullptr on getActiveApplet uses
* Remove redundant includes
* Move subscribedInputs to protected
* More consistent naming scheme
* Fake IAQ values on Non-BSEC2 platforms like Platformio and the original ESP32 (#9663)
* BSEC2 Replacement
- add approximation for IAQ to non-BSEC2 platforms.
- Re-add this sensor to ESP32 targets, and refactor env_extra includes.
- Fix C++ 11 compatibility
* Check for gas resistance 0
* ULED_BUILTIN for 9m2ibr_aprs_lora_tracker (#9685)
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Eric Sesterhenn <eric.sesterhenn@x41-dsec.de>
Co-authored-by: Vortetty <33466216+Vortetty@users.noreply.github.com>
Co-authored-by: Mattatat25 <108779801+mattatat25@users.noreply.github.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Max <rekin.m@gmail.com>
Co-authored-by: Colby Dillion <colby.dillion@pacshealth.com>
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: Tom <116762865+NomDeTom@users.noreply.github.com>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: Chloe Bethel <chloe@9net.org>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Quency-D <55523105+Quency-D@users.noreply.github.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
Co-authored-by: oscgonfer <oscgonfer@users.noreply.github.com>
Co-authored-by: nikl <nikl174@mailbox.org>
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
Co-authored-by: Wessel <wessel@weebl.me>
Co-authored-by: Christian Walther <cwalther@gmx.ch>
Co-authored-by: Jorropo <jorropo.pgm@gmail.com>
Co-authored-by: Eric Barch <ericb@ericbarch.com>
Co-authored-by: Clive Blackledge <clive@ansible.org>
* BSEC2 Replacement
- add approximation for IAQ to non-BSEC2 platforms.
- Re-add this sensor to ESP32 targets, and refactor env_extra includes.
- Fix C++ 11 compatibility
* Check for gas resistance 0
* Allow inkhud user applets to consume inputs with opt-in system
Adds a way for applets to subscribe to input events while keeping it off
by default to preserve compatibility and expected behaviours. Adds
example for use as well.
* Add check for nullptr on getActiveApplet uses
* Remove redundant includes
* Move subscribedInputs to protected
* More consistent naming scheme
The previous PSK check was broken from its introduction in #4643 —
memcmp was used in boolean context without comparing to 0, inverting
the condition. Since no one noticed for over a year, the PSK-based
filtering provided no practical value. Simplifying to always respect
the sender's preference is both more correct and easier to reason about.
* Merge develop into SCD30
* Add SCD30 class
* Fix logging and admin commands
* Minor cleanup and logging improvements
* Minor formatting issue
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Improvements on setTemperature
* Fix casting float-uint16_t
* Pass 100 for resetting temperature offset
* Fix issues pointed out by copilot
* Add quick reboot to set interval quicker on scd30
* Change saveState to only happen after boot and minor log changes
* Fix missing semicolon in one shot mode log
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* simplify the observer pattern, since all the called functions are const getters.
* use arduino macro over std: for numerical values and refactor local variables in drawScrollbar()
* oh, so Cppcheck actually complained about const pointers not being const.
* slowly getting out of ifdef hell
* fix inkHUD warnings as well
* last 2 check warnings
* git checks should fail on low defects from now on
Theses two appear to be buggy on r1-neo and nomadstar meteor pro, they rely on Wire.h being included previously to their import.
Idk why other platforms using the same smart LEDs are working while theses ones don't.
This should make CI green on the dev branch.
Trying this to see if anything bad happen if I were to replace most raw pointers with unique_ptr.
I didn't used std::make_unique since it is only supported in C++14 and onwards but until we update esp32 to arduino 3.x the ESP32 xtensa chips use a C++11 std.
2026-02-14 19:12:59 +01:00
480 changed files with 11172 additions and 2649 deletions
- Before starting on some new big chunk of code, it it is optional but highly recommended to open an issue first
to say "Hey, I think this idea X should be implemented and I'm starting work on it. My general plan is Y, any feedback
is appreciated." This will allow other devs to potentially save you time by not accidentially duplicating work etc...
is appreciated." This will allow other devs to potentially save you time by not accidentally duplicating work etc...
- Please do not check in files that don't have real changes
- Please do not reformat lines that you didn't have to change the code on
- We recommend using the [Visual Studio Code](https://platformio.org/install/ide?install=vscode) editor along with the ['Trunk Check' extension](https://marketplace.visualstudio.com/items?itemName=trunk.io) (In beta for windows, WSL2 for the linux version),
- We recommend using the [Visual Studio Code](https://platformio.org/install/ide?install=vscode) editor along with the ['Trunk Check' extension](https://marketplace.visualstudio.com/items?itemName=trunk.io) (In beta for windows, WSL2 for the Linux version),
because it automatically follows our indentation rules and its auto reformatting will not cause spurious changes to lines.
- If your PR fixes a bug, mention "fixes #bugnum" somewhere in your pull request description.
- If your other co-developers have comments on your PR please tweak as needed.
- Please also enable "Allow edits by maintainers".
- Please do not submit untested code.
- If you do not have the affected hardware to test your code changes adequately against regressions, please indicate this, so that contributors and commnunity members can help test your changes.
- If you do not have the affected hardware to test your code changes adequately against regressions, please indicate this, so that contributors and community members can help test your changes.
- If your PR gets accepted you can request a "Contributor" role in the Meshtastic Discord
stale-issue-message:This issue has not had any comment or update in the last month. If it is still relevant, please post update comments. If no comments are made, this issue will be closed automagically in 7 days.
This directory contains YAML configuration files for meshtasticd. Each file describes a specific hardware configuration, including the LoRa module and pin assignments. These configurations are used by meshtasticd to correctly interface with the hardware.
## Metadata structure
Each configuration file includes a `Meta` section that provides information about the configuration.
This configuration is consumed by configuration-selection tools.
```yaml
Meta:
name:MeshAdv-Pi E22-900M30S# A unique identifier for this configuration.
support:community# community, official, or deprecated; determined by Meshtastic Leads.
compatible:# A list of compatible products or platforms.
- raspberry-pi
```
`name`: A unique identifier for the configuration, typically reflecting the hardware it supports.
`support`: Indicates the level of support for this configuration. It can be one of the following:
-`community`: Supported by the Meshtastic community. Meshtastic Members may not possess, or have not tested this configuration.
-`official`: Fully supported by Meshtastic. Meshtastic Members have tested and verified this configuration.
-`deprecated`: No longer recommended for deployment by Meshtastic.
`compatible`: A list of compatible products or platforms that can use this configuration.
This will vary depending on the intended use case / platform.
Multiple compatible entries can be included. E.g. Armbian `BOARD` value or OpenWrt `TARGET` value.
These tags can be consumed by different configuration-selection tools, filtering based upon their platform/etc.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
Thomas GöttgensandGitHub
AustinandGitHub
Kittiwut KhongkaeoandGitHub
Ethac.chenandBen Meadors
TomandBen Meadors
Philip LykovandBen Meadors
Chloe BethelandBen Meadors
Jason PandBen Meadors
stmka_playgoundandBen Meadors
Robert SasakandBen Meadors
Okan ErturanandBen Meadors
rcatal01andBen Meadors
WesselandBen Meadors
Andrew YongandBen Meadors
oscgonferandBen Meadors
fw190d13andBen Meadors
Catalin PatuleaandBen Meadors
pdxlocationsandGitHub
WesselandGitHub
Clive BlackledgeandGitHub
Larry DoolittleandGitHub
WesselandGitHub
David RembaandGitHub
nikl
Hannes Fuchs
Nashui-Yan
WillyJL
Christian Walther
Jorropo
Eric Barch
harry-iii-lordandGitHub