* PMSA0031 sensors require ~3secs before coming up on I2C
As reported by @MALAONE1 and debugged by @shodan8192 , PMSA0031s
on a RAK4631 take 3 seconds before they can become detectable on I2c.
Add a delay(4000) before I2C scan if the air quality sensor pin
is defined.
Fixes https://github.com/meshtastic/firmware/issues/3690
* Remove 4 second wait and rescan during air quality init for the sensor
* works without but this triggers my OCD
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
As reported by @eureekasigns and @GPSFan, Chatter 2 had begun
to show a blank screen on boot after recent TFT display changes.
Setting TFT_BACKLIGHT_ON LOW resolves the issue.
Fixes https://github.com/meshtastic/firmware/issues/4751
As discovered and tested by @Mictronics, default Serial FIFO size
on the Pico is 32bytes, which is not enough for GPS messages.
This patch increases the Serial GPS FIFO buffer size to 256
for the RP2040 Architecture
fixes https://github.com/meshtastic/firmware/issues/3989
QMC5883L and HMC5883L are 3-axis compasses which are often confused.
As reported by @Africmod, we had the wrong I2C address for the QMC5883L.
This patch fixes the address and adds its HMC5883L so we keep info
about both.
Fixes https://github.com/meshtastic/firmware/issues/4144
This getACK is used to look for ASCII responses, so print ASCII
when GPS_DEBUG is enabled.
This markedly assisted with recent AG3335 debugging. It works great
with other chips too (tested eg ATGM336H). Even UBLOX prints
understandable "GPTXT,01,01,01,PDTI inv format*35." responses.
Credit to bluebrolly. on discord.
if u8i == 135, then u8i++ runs, the loop exits since u8i == 136,
then value for u8i is 136 after the for loop.
then in the next line, ntc_res2[u8i] will read past the end
of the array
At the moment if the result of sleepTime calculations comes out
to zero, we put the GPS into HARDSLEEP (losing all its status) and
then immediately make it ACTIVE again.
This patch avoids that toga.
fixes https://github.com/meshtastic/firmware/issues/4657
AG33352 is a Mediatek/Airoha GPS/GLONASS/Galileo/BeiDou receiver.
Patch adds relevant detection and setup code.
Thanks to Bluebrolly and kongduino for providing the relevant
information and testing.
This patch also fixes support for the A3335, which is a related chip.
The setup and detection code now works as tested on a real life
T-1000E!
Thanks to @gpsfan for the guidance.
This patch takes inspiration from our I2CDetect code where we have
many sensors that can be detected rather simply. It creates a new
macro,
PROBE_SIMPLE(Chip name, Command to run, response, Driver, timeout)
and converts existing simple cases to use this macro.
Thanks to user Goyath on Discord, we discovered that in Japan the
250mW radio level requires licensing, and 20mW is the practical
limit. We also discovered that a duty cycle of 10% is needed on
most frequencies.
CH 24-38 920.5-923.5 20mW no airtime restrictions
CH 39-61 923.5-928.1 20mW 10% airtime
After the recent GPS power work we have an clear set of
definitions for turning GPS on and off. Rather than manipulating
specific heltec tracker-related pins in main setu, the relevant
power management code in the GPS module will turn things
on/off later as needed.
* Address some FIXME comments
These comments have since been addressed by more modern code.
Remove them to reduce the clutter in the codebase.
* Remove 'dumb idea' from SimpleAllocator
4 year old code that was set never to run can probably be safely
deleted.
There are no calls to the functions defined in Nimble from this
class. See also older comment on line 8 about the dream to seperate
mesh and bluetooth :)
* Add GPS detection code for Airoha AG3335
Airoha AG3335 is used in Seeed T-1000E Tracker
* Add support for Airoha AG3335
Airoha AG3335 is used in Seeed T-1000E Tracker. This adds
detection code, and code to configure its use.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
As reported by @mrekin, the previous changes to the platformio
custom build script may not work on windows. Change to use
python3 instead of a call to /usr/bin/env python3.
The call to generate UF2 files in the platformio custom script was
a bare call to python. In some environments, this command won't
exist in this way. Instead, use the standard env approach to find
the right python.
Additionally, add the shebang line on line 1 so this script can be
executed standalone if needed.
* Cleanup - remove unused defines.
There were a number of defined variables that were carried over
from old code. - Removed.
Also a typo. - Fixed fix.
Also duplicate definitions of the number of seconds in a day.
-deduplicated.
* Cleanup - remove unused defines.
There were a number of defined variables that were carried over
from old code. - Removed.
Also a typo. - Fixed fix.
Also duplicate definitions of the number of seconds in a day.
-deduplicated.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
It turns out that the Air530z is a GNSS_MODEL_MTK. Our existing
code detects and configures it properly. This patch removes a
couple of AIROHA ifdefs since they are not required for a
working GPS.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Cleanup GPS, add UC6580 autodetect
Our GPS code autodetects devices by default. Previously UC6580 was
statically assigned, and had its own baudrate configuration inside
the GPS code.
This change adds autodetect functionality for the UC6580 and moves
any 'special' GPS baud rate requirements for a variant out into the
variant configuration. Thereby cleaning up core GPS code a little,
saving the whales, and curing global warming.
New Functionality:
* If GPS_BAUDRATE is defined in variant.h, GPS autodetection will
try that baudrate first.
* UC6580 GPS chips are now automatically detected
* Only run speedSelect skip the first time
* Cleanup GPS, add UC6580 autodetect
Our GPS code autodetects devices by default. Previously UC6580 was
statically assigned, and had its own baudrate configuration inside
the GPS code.
This change adds autodetect functionality for the UC6580 and moves
any 'special' GPS baud rate requirements for a variant out into the
variant configuration. Thereby cleaning up core GPS code a little,
saving the whales, and curing global warming.
New Functionality:
* If GPS_BAUDRATE is defined in variant.h, GPS autodetection will
try that baudrate first.
* UC6580 GPS chips are now automatically detected
* Cleanup GPS, add UC6580 autodetect
Our GPS code autodetects devices by default. Previously UC6580 was
statically assigned, and had its own baudrate configuration inside
the GPS code.
This change adds autodetect functionality for the UC6580 and moves
any 'special' GPS baud rate requirements for a variant out into the
variant configuration. Thereby cleaning up core GPS code a little,
saving the whales, and curing global warming.
New Functionality:
* If GPS_BAUDRATE is defined in variant.h, GPS autodetection will
try that baudrate first.
* UC6580 GPS chips are now automatically detected
* Remove Airoha baud rate code
It's no longer needed.
Previously, we used sudo and chmod to make mergehex executable in
our build script. This change attempts to set the executable bit
using git properties and remove the dependence on elevated
permissions.
* Fix protobuf structs handling (#4140)
* Fix protobuf structs handling
* Log instead of assert
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* BLE based logging (#4146)
* WIP log characteristic
* Bluetooth logging plumbing
* Characteristic
* Callback
* Check for nullptr
* Esp32 bluetooth impl
* Formatting
* Add thread name and log level
* Add settings guard
* Remove comments
* Field name
* Fixes esp32
* Open it up
* Whoops
* Move va_end past our logic
* Use `upload_protocol = esptool` as with the other heltec devices instead of `esp-builtin` (#4151)
* Standardize lat/lon position logs (#4156)
* Standardize lat/lon position logs
* Missed sone and condensed logs
* [create-pull-request] automated change (#4157)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Pause BLE logging during want_config flow (#4162)
* Update NimBLE to 1.4.2 (#4163)
* Implement replies for all telemetry types based on variant tag (#4164)
* Implement replies for all telemetry types based on variant tag
* Remove check for `ignoreRequest`: modules can set this, don't need to check
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Esptool is better
* Explicitly set characteristic
* fix INA3221 sensor (#4168)
- pass wire to begin()
- remove redundant setAddr() (already set in header)
* Show compass on waypoint frame; clear when waypoint deleted (#4116)
* Clear expired or deleted waypoint frame
* Return 0 to CallbackObserver
* Add a missing comment
* Draw compass for waypoint frame
* Display our own waypoints
* [create-pull-request] automated change (#4171)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Add semihosting support for nrf52 devices (#4137)
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* fix my botched merge - keep board_level = extra flag for rak3631_dbg
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* [create-pull-request] automated change (#4174)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Display alerts (#4170)
* Move static functions into Screen.h, show compass during calibration
* Move to _fontHeight macro to avoid collision
* Move some alert functions to new alert handler
* Catch missed reboot code
* ESP32 fixes
* Bump esp8266-oled-ssd1306
* Fixes for when a device has no screen
* Use new startAlert(char*) helper class
* Add EINK bits back to alert handling
* Add noop class for no-display devices
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Send file system manifest up on want_config (#4176)
* Send file system manifest up on want_config
* Platform specific methods
* Helps to actually make the change
* Clear
* tell vscode, if formatting, use whatever our trunk formatter wants (#4186)
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* fix the build - would loop forever if there were no files to send (#4188)
* Show owner.short_name on boot (and E-Ink sleep screen) (#4134)
* Show owner.short_name on boot and sleep screen (on e-ink)
* Update Screen.cpp - new line for short_name
Boot screen short_name now below the region setting.
Looks better on small screens.
* Draw short_name on right
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* nrf52 soft device will watchdog if you use ICE while BT on... (#4189)
so have debugger disable bluetooth.
* correct xiao_ble build preventing sx1262 init (#4191)
* Force a compile time failur if FromRadio or ToRadio get larger than (#4190)
a BLE packet size. We are actually very close to this threshold so
important to make sure we don't accidentally pass it.
* Clear vector after complete config state (#4194)
* Clear after complete config
* Don't collect . entries
* Log file name and size
* [create-pull-request] automated change (#4200)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Make the logs Colorful! (#4199)
* Squash needlessly static functions (#4183)
* Trim extra vprintf and filter for unprintable characters
* Deprecate Router Client role (and make it Client) (#4201)
* [create-pull-request] automated change (#4205)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Move waypoint (#4202)
* Move waypoint screen draw into the waypoint module
* Get the observer set up for the waypoint screen draw
* Static squashing: screen dimensions
Macros moved back to Screen.cpp, as a band-aid until we eventually move all those static functions into the Screen class.
* Move getCompassDiam into Screen class
(supress compiler warnings)
At this stage, the method is still static, because it's used by drawNodeInfo, which has no tidy reference to our screen instance.
This is probably just another band-aid until these static functions all move.
* Use new getCompassDiam function in AccelerometerThread
* Properly gate display code in WaypointModule
---------
Co-authored-by: Todd Herbert <herbert.todd@gmail.com>
* Fix flakey phone api transition from file manifest to complete (#4209)
* Try fix flakey phone api transition from file manifest to complete
* Skip
* enable colors in platformio serial monitor (#4217)
* When talking via serial, encapsulate log messages in protobufs if necessary (#4187)
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* [create-pull-request] automated change (#4218)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Fix SHT41 support (#4222)
* Add SHT41 Serial to I2c Detection Code
On the Seeed Wio-WM1110 Dev Kit board, the SHT41 chip was being
incorrectly detected as SHT31.
This patch adds the necessary serial number for the SHT41 chip to
be correctly detected.
fixesmeshtastic/firmware#4221
* Add missing sensor read for SHT41
* Typo fix in logs - mhz - MHz (#4225)
As reported by karamo, a few different places in our logs had
incorrect capitalization of MHz.
fixesmeshtastic/firmware#4126
* New new BLE logging characteristic with LogRecord protos (#4220)
* New UUID
* New log radio characteristic with LogRecord protobuf
* LogRecord
* Merge derp
* How did you get there
* Trunk
* Fix length
* Remove assert
* minor cleanup proposal (#4169)
* MESHTASTIC_EXCLUDE_WIFI and HAS_WIFI cleanup...
Our code was checking HAS_WIFI and the new MESHTASTIC_EXCLUDE_WIFI
flags in various places (even though EXCLUDE_WIFI forces HAS_WIFI
to 0). Instead just check HAS_WIFI, only use EXCLUDE_WIFI inside
configuration.h
* cleanup: use HAS_NETWORKING instead of HAS_WIFI || HAS_ETHERNET
We already had HAS_NETWORKING as flag in MQTT to mean 'we have
tcpip'. Generallize that and move it into configuration.h so that
we can use it elsewhere.
* Use #pragma once, because supported by gcc and all modern compilers
instead of #ifdef DOTHFILE_H etc...
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Add PowerMon support (#4155)
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* fix linter warning
* Cleanup buffer
* Merge hex for wm1110 target(s)
* Only sdk
* Sudo
* Fix exclude macros (#4233)
* fix MESHTASTIC_EXCLUDE_BLUETOOTH
* fix HAS_SCREEN=0
* fix MESHTASTIC_EXCLUDE_GPS
* fix typo in build-nrf52.sh (#4231)
chmod is the command, '+x' is the argument.
* Tidy Wireless Paper variant files (#4238)
* Quick tidy of pins_arduino.h
Matches requests made at https://github.com/meshtastic/firmware/pull/4226#discussion_r1664183480)
* Tidy variant.h
* Change deprecated ADC attenuation parameter
From 11dB to 12dB. Resolves compiler warning. Allegly, no impact on function: `This is deprecated, it behaves the same as `ADC_ATTEN_DB_12`
* Updated raspbian CI to update apt repository ahead of libbluetooth. (#4243)
* Fix BLE logging on nrf52 (#4244)
* allow ble logrecords to be fetched either by NOTIFY or INDICATE ble types
This allows 'lossless' log reading. If client has requested INDICATE
(rather than NOTIFY) each log record emitted via log() will have to fetched
by the client device before the meshtastic node can continue.
* Fix serious problem with nrf52 BLE logging.
When doing notifies of LogRecords it is important to use the
binary write routines - writing using the 'string' write won't work.
Because protobufs can contain \0 nuls inside of them which if being
parsed as a string will cause only a portion of the protobuf to be sent.
I noticed this because some log messages were not getting through.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix build when HAS_NETWORKING is false on nrf52 (#4237)
(tested on a rak4631 by setting HAS_ETHERNET false when shrinking
image)
* If `toPhoneQueue` is full, still increment `fromNum` to avoid client never getting packets (#4246)
* Update to SoftDevice 7.3.0 for wio-sdk-wm1110 and wio-tracker-wm1110 (#4248)
* Update variant.h
* Update wio-tracker-wm1110.json
* Update wio-sdk-wm1110.json
* Update platformio.ini
* Update platformio.ini
* Add files via upload
* Add files via upload
* Update variant.h
* Cleanup NRF s140 Softdevice variants (#4252)
Note: This idea is originally from @caveman99 and should be
credited as such. Submitting as a separate PR so the work in
meshtastic/firmware#4148 can be a bit cleaner and Seeed boards
can build while that work is ongoing.
The nrf52 boards that depend on the v7 softdevice all use the same
code and linker files. Rather than duplicate the code, keep it
all together with the platform.
* Remove tracker variant specific soft device headers (#4255)
* [create-pull-request] automated change (#4247)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Add wio-sdk-wm1110 to build. (#4258)
The wio-sdk-wm1110 is distinct from the wio-tracker-wm1110, with
different platformio build options and pin config.
This change adds the wio-sdk-wm1110 to the CI matrix so firmware
is built as part of release.
* fix python warning in uf2conf (#4235)
the old regex worked but was technically incorrect. fixes:
Generating NRF52 uf2 file
/home/kevinh/development/meshtastic/firmware/bin/uf2conv.py:195: SyntaxWarning: invalid escape sequence '\s'
words = re.split('\s+', line)
Converting to uf2, output size: 1458688, start address: 0x26000
* Collect hex files and specifically wm1110 sdk
* Skip dfu file for sdk (for now)
* Helps if you remove the original clause
* Add Heltec new boards. (#4226)
* Add Heltec new boards
* Update variant.h
disable RTC by default
* Add Heltec New boards
* Add Heltec new boards
* Update Heltec Mesh Node definition.
* Update Heltec Vision Mater E290
* [create-pull-request] automated change (#4259)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Trunk fmt
* Fix macros
* Move e290 to board level extra while CI is broken
* Tell trunk to ignore bin folder
* Fix missing
* Update trunk.yaml, fix whitespace
* Update trunk.yaml
* Update build_raspbian_armv7l.yml --fix-missing
* [create-pull-request] automated change (#4263)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* GPS Power State tidy-up (#4161)
* Refactor GPSPowerState enum
Identifies a case where the GPS hardware is awake, but an update is not yet desired
* Change terminology
* Clear old lock-time prediction on triple press
* Use exponential smoothing to predict lock time
* Rename averageLockTime to predictedLockTime
* Attempt: Send PMREQ with duration 0 on MCU deep-sleep
* Attempt 2: Send PMREQ with duration 0 on MCU deep-sleep
* Revert "Attempt 2: Send PMREQ with duration 0 on MCU deep-sleep"
This reverts commit 8b697cd2a445355dcfab5b33e0ce7a3128cab151.
* Revert "Attempt: Send PMREQ with duration 0 on MCU deep-sleep"
This reverts commit 9d29ec7603a88056b9115796b29b5023165a93bb.
* Remove unused notifyGPSSleep Observable
Handled with notifyDeepSleep, and enable() / disable()
* WIP: simplify GPS power management
An initial attempt only.
* Honor #3e9e0fd
* No-op when moving between GPS_IDLE and GPS_ACTIVE
* Ensure U-blox GPS is awake to receive indefinite sleep command
* Longer pause when waking U-blox to send sleep command
* Actually implement soft and hard sleep..
* Dynamically estimate the threshold for GPS_HARDSLEEP
* Fallback to GPS_HARDSLEEP, if GPS_SOFTSLEEP unsupported
* Move "excessive search time" behavior to scheduler class
* Minor logging adjustments
* Promote log to warning
* Gratuitous buffer clearing on boot
* Fix inverted standby pin logic
Specifically the standby pin for L76B, L76K and clones
Discovered during T-Echo testing: totally broken function, probe method failing.
* Remove redundant pin init
Now handled by setPowerState
* Replace max() with if statements
Avoid those platform specific implementations..
* Trunk formatting
New round of settings.json changes keep catching me out, have to remember to re-enable my "clang-format" for windows workaround.
* Remove some asserts from setPowerState
Original aim was to prevent sending a 0 second PMREQ to U-blox hardware as part of a timed sleep (GPS_HARDSLEEP, GPS_SOFTSLEEP). I'm not sure this is super important, and it feels tidier to just allow the 0 second sleeptime here, rather than fudge the sleeptime further up.
* Fix an error determining whether GPS_SOFTSLEEP is supported
* Clarify a log entry
* Set PIN_STANDBY for MCU deep-sleep
Required to reach TTGO's advertised 0.25mA sleep current for T-Echo. Without this change: ~6mA.
* Optimize the shutdown current of RAK10701 to around 25uA (#4260)
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* INA3221 sensor: use for bus voltage & environment metrics (#4215)
* use INA3221 for bus voltage; fixes for telemetry variants
- add to sensors available for environment telemetry
(to report voltage/current)
- add vars to define channels to use for battery voltage
(for getBusVoltage) and environment metrics (default
to CH1 for both)
- write to the correct fields on the measurement struct
depending on the measurement variant, and DRY up the
sensor measurement collection code a bit
- this might be suitable for a common implementation for
the INA* sensors in a future PR...
* formatting
* derp
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* WM1110 SDK kit enter serial DFU and add deployment packages (#4266)
* Switch default upload protocol to nrfutil so that pio generates zip deploy packages
* Enter serial DFU on SDK board
* Remove guard for DFU zip from SDK build
* NRF_USE_SERIAL_DFU macro instead
* Show specific frame when updating screen (#4264)
* Updated setFrames in Screen.cpp
Added code to attempt to revert back to the same frame that user was on prior to setFrame reload.
* Space added Screen.cpp
* Update Screen.cpp
Make screen to revert to Frame 0 if the originally displayed frame is no longer there.
* Update Screen.cpp
Inserted boolean holdPosition into setFrames to indicate the requirement to stay on the same frame ( if =true) or else it will switch to new frame .
Only Screen::handleStatusUpdate calls with setFrame(true). ( For Node Updates)
All other types of updates call as before setFrame(), so it will change focus as needed.
* Hold position, even if number of frames increases
* Hold position, if handling an outgoing text message
* Update Screen.cpp
* Reverted chnages related to devicestate.has_rx_text_message
* Reset to master
* CannedMessages only handles routing packets when waiting for ACK
Previously, this was calling Screen::setFrames at unexpected times
* Gather position info about screen frames while regenerating
* Make admin module observable
Notify only when relevant. Currently: only to handle remove_nodenum.
* Optionally specify which frame to focus when setFrames runs
* UIFrameEvent uses enum instead of multiple booleans
* Allow modules to request their own frame to be focussed
This is done internally by calling MeshModule::requestFocus()
Easier this way, insteady of passing the info in the UIFrameEvent:
* Modules don't always know whether they should be focussed until after the UIFrameEvent has been raised, in dramFrame
* Don't have to pass reference to module instance as parameter though several methods
* E-Ink screensaver uses FOCUS_PRESERVE
Previously, it had its own basic implementation of this.
* Spelling: regional variant
* trunk
* Fix HAS_SCREEN guarding
* More HAS_SCREEN guarding
---------
Co-authored-by: BIST <77391720+slash-bit@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: slash-bit <v-b2@live.com>
* Move up telemetry defaults to every 30 minutes (#4274)
* Don't send node info interrogation when ch. util is >25% (#4273)
* Moar LR1110 Targets
* update SD_FLASH_SIZE to 0x27000 (#4232)
The 7.3.0 softdevice needs the extra 1000 :)
* Fix spacing.
---------
Co-authored-by: Mike <mikhael.skvortsov@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Mike G <mkgin@users.noreply.github.com>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: GUVWAF <78759985+GUVWAF@users.noreply.github.com>
Co-authored-by: Warren Guy <5602790+warrenguy@users.noreply.github.com>
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
Co-authored-by: geeksville <kevinh@geeksville.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Alexander <156134901+Dorn8010@users.noreply.github.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: quimnut <github@dopegoat.com>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
Co-authored-by: Agent Blu, 006 <blu006@ucr.edu>
Co-authored-by: Mark Trevor Birss <markbirss@gmail.com>
Co-authored-by: Aaron.Lee <32860565+Heltec-Aaron-Lee@users.noreply.github.com>
Co-authored-by: Daniel.Cao <144674500+DanielCao0@users.noreply.github.com>
Co-authored-by: BIST <77391720+slash-bit@users.noreply.github.com>
Co-authored-by: slash-bit <v-b2@live.com>
The wio-sdk-wm1110 is distinct from the wio-tracker-wm1110, with
different platformio build options and pin config.
This change adds the wio-sdk-wm1110 to the CI matrix so firmware
is built as part of release.
* Fix protobuf structs handling (#4140)
* Fix protobuf structs handling
* Log instead of assert
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* BLE based logging (#4146)
* WIP log characteristic
* Bluetooth logging plumbing
* Characteristic
* Callback
* Check for nullptr
* Esp32 bluetooth impl
* Formatting
* Add thread name and log level
* Add settings guard
* Remove comments
* Field name
* Fixes esp32
* Open it up
* Whoops
* Move va_end past our logic
* Use `upload_protocol = esptool` as with the other heltec devices instead of `esp-builtin` (#4151)
* Standardize lat/lon position logs (#4156)
* Standardize lat/lon position logs
* Missed sone and condensed logs
* [create-pull-request] automated change (#4157)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Pause BLE logging during want_config flow (#4162)
* Update NimBLE to 1.4.2 (#4163)
* Implement replies for all telemetry types based on variant tag (#4164)
* Implement replies for all telemetry types based on variant tag
* Remove check for `ignoreRequest`: modules can set this, don't need to check
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Esptool is better
* Explicitly set characteristic
* fix INA3221 sensor (#4168)
- pass wire to begin()
- remove redundant setAddr() (already set in header)
* Show compass on waypoint frame; clear when waypoint deleted (#4116)
* Clear expired or deleted waypoint frame
* Return 0 to CallbackObserver
* Add a missing comment
* Draw compass for waypoint frame
* Display our own waypoints
* [create-pull-request] automated change (#4171)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Add semihosting support for nrf52 devices (#4137)
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* fix my botched merge - keep board_level = extra flag for rak3631_dbg
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* [create-pull-request] automated change (#4174)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Display alerts (#4170)
* Move static functions into Screen.h, show compass during calibration
* Move to _fontHeight macro to avoid collision
* Move some alert functions to new alert handler
* Catch missed reboot code
* ESP32 fixes
* Bump esp8266-oled-ssd1306
* Fixes for when a device has no screen
* Use new startAlert(char*) helper class
* Add EINK bits back to alert handling
* Add noop class for no-display devices
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Send file system manifest up on want_config (#4176)
* Send file system manifest up on want_config
* Platform specific methods
* Helps to actually make the change
* Clear
* tell vscode, if formatting, use whatever our trunk formatter wants (#4186)
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* fix the build - would loop forever if there were no files to send (#4188)
* Show owner.short_name on boot (and E-Ink sleep screen) (#4134)
* Show owner.short_name on boot and sleep screen (on e-ink)
* Update Screen.cpp - new line for short_name
Boot screen short_name now below the region setting.
Looks better on small screens.
* Draw short_name on right
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* nrf52 soft device will watchdog if you use ICE while BT on... (#4189)
so have debugger disable bluetooth.
* correct xiao_ble build preventing sx1262 init (#4191)
* Force a compile time failur if FromRadio or ToRadio get larger than (#4190)
a BLE packet size. We are actually very close to this threshold so
important to make sure we don't accidentally pass it.
* Clear vector after complete config state (#4194)
* Clear after complete config
* Don't collect . entries
* Log file name and size
* [create-pull-request] automated change (#4200)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Make the logs Colorful! (#4199)
* Squash needlessly static functions (#4183)
* Trim extra vprintf and filter for unprintable characters
* Deprecate Router Client role (and make it Client) (#4201)
* [create-pull-request] automated change (#4205)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Move waypoint (#4202)
* Move waypoint screen draw into the waypoint module
* Get the observer set up for the waypoint screen draw
* Static squashing: screen dimensions
Macros moved back to Screen.cpp, as a band-aid until we eventually move all those static functions into the Screen class.
* Move getCompassDiam into Screen class
(supress compiler warnings)
At this stage, the method is still static, because it's used by drawNodeInfo, which has no tidy reference to our screen instance.
This is probably just another band-aid until these static functions all move.
* Use new getCompassDiam function in AccelerometerThread
* Properly gate display code in WaypointModule
---------
Co-authored-by: Todd Herbert <herbert.todd@gmail.com>
* Fix flakey phone api transition from file manifest to complete (#4209)
* Try fix flakey phone api transition from file manifest to complete
* Skip
* enable colors in platformio serial monitor (#4217)
* When talking via serial, encapsulate log messages in protobufs if necessary (#4187)
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* [create-pull-request] automated change (#4218)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Fix SHT41 support (#4222)
* Add SHT41 Serial to I2c Detection Code
On the Seeed Wio-WM1110 Dev Kit board, the SHT41 chip was being
incorrectly detected as SHT31.
This patch adds the necessary serial number for the SHT41 chip to
be correctly detected.
fixesmeshtastic/firmware#4221
* Add missing sensor read for SHT41
* Typo fix in logs - mhz - MHz (#4225)
As reported by karamo, a few different places in our logs had
incorrect capitalization of MHz.
fixesmeshtastic/firmware#4126
* New new BLE logging characteristic with LogRecord protos (#4220)
* New UUID
* New log radio characteristic with LogRecord protobuf
* LogRecord
* Merge derp
* How did you get there
* Trunk
* Fix length
* Remove assert
* minor cleanup proposal (#4169)
* MESHTASTIC_EXCLUDE_WIFI and HAS_WIFI cleanup...
Our code was checking HAS_WIFI and the new MESHTASTIC_EXCLUDE_WIFI
flags in various places (even though EXCLUDE_WIFI forces HAS_WIFI
to 0). Instead just check HAS_WIFI, only use EXCLUDE_WIFI inside
configuration.h
* cleanup: use HAS_NETWORKING instead of HAS_WIFI || HAS_ETHERNET
We already had HAS_NETWORKING as flag in MQTT to mean 'we have
tcpip'. Generallize that and move it into configuration.h so that
we can use it elsewhere.
* Use #pragma once, because supported by gcc and all modern compilers
instead of #ifdef DOTHFILE_H etc...
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Add PowerMon support (#4155)
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* fix linter warning
* Cleanup buffer
* Merge hex for wm1110 target(s)
* Only sdk
* Sudo
* Fix exclude macros (#4233)
* fix MESHTASTIC_EXCLUDE_BLUETOOTH
* fix HAS_SCREEN=0
* fix MESHTASTIC_EXCLUDE_GPS
* fix typo in build-nrf52.sh (#4231)
chmod is the command, '+x' is the argument.
* Tidy Wireless Paper variant files (#4238)
* Quick tidy of pins_arduino.h
Matches requests made at https://github.com/meshtastic/firmware/pull/4226#discussion_r1664183480)
* Tidy variant.h
* Change deprecated ADC attenuation parameter
From 11dB to 12dB. Resolves compiler warning. Allegly, no impact on function: `This is deprecated, it behaves the same as `ADC_ATTEN_DB_12`
* Updated raspbian CI to update apt repository ahead of libbluetooth. (#4243)
* Fix BLE logging on nrf52 (#4244)
* allow ble logrecords to be fetched either by NOTIFY or INDICATE ble types
This allows 'lossless' log reading. If client has requested INDICATE
(rather than NOTIFY) each log record emitted via log() will have to fetched
by the client device before the meshtastic node can continue.
* Fix serious problem with nrf52 BLE logging.
When doing notifies of LogRecords it is important to use the
binary write routines - writing using the 'string' write won't work.
Because protobufs can contain \0 nuls inside of them which if being
parsed as a string will cause only a portion of the protobuf to be sent.
I noticed this because some log messages were not getting through.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix build when HAS_NETWORKING is false on nrf52 (#4237)
(tested on a rak4631 by setting HAS_ETHERNET false when shrinking
image)
* If `toPhoneQueue` is full, still increment `fromNum` to avoid client never getting packets (#4246)
* Update to SoftDevice 7.3.0 for wio-sdk-wm1110 and wio-tracker-wm1110 (#4248)
* Update variant.h
* Update wio-tracker-wm1110.json
* Update wio-sdk-wm1110.json
* Update platformio.ini
* Update platformio.ini
* Add files via upload
* Add files via upload
* Update variant.h
---------
Co-authored-by: Mike <mikhael.skvortsov@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Mike G <mkgin@users.noreply.github.com>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: GUVWAF <78759985+GUVWAF@users.noreply.github.com>
Co-authored-by: Warren Guy <5602790+warrenguy@users.noreply.github.com>
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
Co-authored-by: geeksville <kevinh@geeksville.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Alexander <156134901+Dorn8010@users.noreply.github.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: quimnut <github@dopegoat.com>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
Co-authored-by: Agent Blu, 006 <blu006@ucr.edu>
Co-authored-by: Mark Trevor Birss <markbirss@gmail.com>
Note: This idea is originally from @caveman99 and should be
credited as such. Submitting as a separate PR so the work in
meshtastic/firmware#4148 can be a bit cleaner and Seeed boards
can build while that work is ongoing.
The nrf52 boards that depend on the v7 softdevice all use the same
code and linker files. Rather than duplicate the code, keep it
all together with the platform.
* Add SHT41 Serial to I2c Detection Code
On the Seeed Wio-WM1110 Dev Kit board, the SHT41 chip was being
incorrectly detected as SHT31.
This patch adds the necessary serial number for the SHT41 chip to
be correctly detected.
fixesmeshtastic/firmware#4221
* Add missing sensor read for SHT41
The TW region had now power limit set, so defaulted to 16dBm.
The relevant regulation is section 5.8.1 of the Low-power Radio-frequency Devices Technical Regulations, which notes the limits of 0.5W (27dBM) indoor or coastal, 1.0W (30dBM) outdoor.
This patch updates the power limit to 27dbM, using the the lower limit specified in the regulations to be conservative.
Regulation references:
https://www.ncc.gov.tw/english/files/23070/102_5190_230703_1_doc_C.PDF (latest English version)
https://gazette.nat.gov.tw/egFront/e_detail.do?metaid=147283 (latest Chinese version, February 2024)
geeksville
Jonathan Bennett
Alexander
quimnut
Manuel
Mark Trevor Birss
Aaron.Lee
Daniel.Cao
BIST
slash-bit