* Add define for screen I2C frequency
* Add functions to get I2C screen frequency and port
* Make reclock function aware of screen-set I2C speeds
* Refurbish ReClockI2C API
* Make ReClockI2C API class
* Use new API in AirQualityTelemetry module
* Minor changes on some logs
* Update esp8266-oled library
* Fix esp8266 library
* Minor logging changes
* Improve setClock and restoreClock cases
* Make getter functions const, fix capitalisaiton of new functions
* Minor typo, remove pragma once
* Low prio debug fixes
* Mark getter functions as const (properly)
* Fix LOG based on coderabbit feedback
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Seeed Tracker X1 Support
* silence CPPCheck
* fix macro order regression and adapt stm32hal for new radiolib
* STM32 is a radiolib upstream fix ( https://github.com/jgromes/RadioLib/issues/1825 )
* fix STM32 regression
* Seeed Tracker X1 Support
* silence CPPCheck
* fix macro order regression and adapt stm32hal for new radiolib
* STM32 is a radiolib upstream fix ( https://github.com/jgromes/RadioLib/issues/1825 )
* fix STM32 regression
* address copilot OCD
* Split behavior only when the two LEDs are on distinct pins.
* bring naming in line with the other seeed devices
* update env name to fit convention too
* guarantee evaluation order
* Guard sensor readings against null values, make sensor use less power
* Fix T1000-E QMA6100P I2C probing
* Refactored to make generic
* address copilot comments
* fix(i2c): address copilot comments on QMA6100P scanning and hardware init
- ScanI2CTwoWire: gate bounded QMA6100P probing to addresses 0x12/0x13 only
(Copilot comment: avoid blocking other I2C device detection on nRF52)
Falls back to normal Wire probing for all other addresses, allowing BMM150
and other devices at overlapping addresses to be properly detected.
- Nrf52Twim: suppress cppcheck redundantAssignment on ENABLE register write
(intentional disable→configure→enable pattern for hardware safety; explicit
disable ensures known state before configuration even if already disabled)
Co-Authored-By: Claude Haiku 4.5 <noreply@anthropic.com>
* Nrf52Twim: gate on HAS_QMA6100P; suppress cppcheck redundantAssignment
The TWIM helper is only used by the QMA6100P probing path (T1000-E, the sole
board defining HAS_QMA6100P). It was gated only on ARCH_NRF52, so it compiled
as dead code on every other nRF52 board and was analyzed by the rak4631
cppcheck job -- which failed on a redundantAssignment false positive.
Gate the header and source on HAS_QMA6100P so the file is only built/analyzed
where it is actually used. Also keep an inline suppression on the ENABLE
re-assignment (a required volatile disable->reconfigure->enable sequence) for
the case where the T1000-E build is run through cppcheck locally.
Fixes the rak4631 cppcheck CI failure for PR #10713.
Co-Authored-By: Claude Opus 4.8 (1M context) <noreply@anthropic.com>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: nomdetom <nomdetom@protonmail.com>
Co-authored-by: Tom <116762865+NomDeTom@users.noreply.github.com>
Co-authored-by: Claude Haiku 4.5 <noreply@anthropic.com>
* LR2021 radio on NRF_Promicro
Co-authored-by: Copilot <copilot@github.com>
* Refactor LR2021 interface includes and conditional compilation for improved clarity
Co-authored-by: Copilot <copilot@github.com>
* Refactor LR20x0 interface: remove unused includes and update comments for clarity
* Fix LR2021 max power definitions and add radio type detection tests
* remove potato radio type detection tests
* Include placeholder for DCDC - currently requires godmode
* Added godmode features - not enabled by default
---------
Co-authored-by: Copilot <copilot@github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix INA226 detection for non-TI compatible chip (Silergy)
* Removed extra I2C transaction + 20ms delay on every scan of address 0x40 (including real SHT2x sensors).
Changes suggested by Copilot
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Apply formatting (trunk fmt)
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Consolidate SHTs into one class
* Remove separate SHT imports
* Create one single SHTXX sensor type
* Let the SHTXXSensor class handle variant detection
* Minor logging improvements
* Add functions to set accuracy on SHT3X and SHT4X
* Fix variable init in constructor
* Add bus to SHT sensor init
* Update src/modules/Telemetry/Sensor/SHTXXSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/Telemetry/Sensor/SHTXXSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix accuracy conditions on SHTXX
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Merge upstream
* Add SHT2X detection on 0x40
* Read second part of SHT2X serial number
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Enable pre-hop drop handling by default
* Remove early break if BME/DPS sensors are not detected at the BME address
* revert sneaky change
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Enable pre-hop drop handling by default
* Remove early break if BME/DPS sensors are not detected at the BME address
* revert sneaky change
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Cardputer Kit
BMI270 WIP
* BMI270 support
* verify that the number of bytes read matches the requested length
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* trunk'd
* remove excessive logging
* Kick the screen when unsleeping
* Update the st7789 library, and enable displayon and displayoff
* Battery detection
* Default to arrow keys and enter, while in menus.
* Enable Backlight control
* Update src/detect/ScanI2CTwoWire.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* updateState method now accepts shouldRequestFocus parameter for better maintainability
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Merge develop into SCD30
* Add SCD30 class
* Fix logging and admin commands
* Minor cleanup and logging improvements
* Minor formatting issue
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Improvements on setTemperature
* Fix casting float-uint16_t
* Pass 100 for resetting temperature offset
* Fix issues pointed out by copilot
* Add quick reboot to set interval quicker on scd30
* Change saveState to only happen after boot and minor log changes
* Fix missing semicolon in one shot mode log
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Initial implementation for SFA30Sensor
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Add functional SCD4X
* Fix screen frame for CO2
* Add admin commands to SCD4X class
* Add further admin commands and fixes.
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 084796920179e80a7500d36c25fd4d82b3ef4214.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Small reordering in PMS class for consistency
* If one sensor fails, AQ telemetry still reports data
* Small formatting fix
* Add SEN5X to AQI in ScanI2C
* SCD4X now part of AQ module with template list
* Fixes difference between idle and sleep
* In LowPower, sleep is disabled
* Requires testing for I2C clock comms for commands
* Remove unnecessary import
* Add co2 to serialized AQ metrics
* Add SFA30 with new sensor template in AQ module
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Fix uninitMemberVars
* Fix import error for SCD4X
* Fix I2CClock logic
* Fix not reclocking back to 700000Hz
* Fix multiple sensors being read simultaneously
* The logic in AQ module is different to the one in EnvironmentTelemetryModule. In Env module, if any sensor fails to getMetrics, no valid flag for the module. This prevents other sensors to report data.
* Fix pending clock change in PMSA003
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Make sure clock is always set to needed value
* Fix returns
* Fix trunk
* Fix on condition in reclock
* Fix trunk
* Final SFA30 class implementation
* Add HCHO to screen and improve logs
* Add metrics to mesh packet serializer
* Minor fixes in logs
* OCD tidy up of logs
* Fix sleep function
* Remove old I2C_CLOCK_SPEED code
---------
Co-authored-by: nikl <nikl174@mailbox.org>
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Add functional SCD4X
* Fix screen frame for CO2
* Add admin commands to SCD4X class
* Add further admin commands and fixes.
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 084796920179e80a7500d36c25fd4d82b3ef4214.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Small reordering in PMS class for consistency
* If one sensor fails, AQ telemetry still reports data
* Small formatting fix
* Add SEN5X to AQI in ScanI2C
* SCD4X now part of AQ module with template list
* Fixes difference between idle and sleep
* In LowPower, sleep is disabled
* Requires testing for I2C clock comms for commands
* Remove unnecessary import
* Add co2 to serialized AQ metrics
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Fix uninitMemberVars
* Fix import error for SCD4X
* Fix I2CClock logic
* Fix not reclocking back to 700000Hz
* Fix multiple sensors being read simultaneously
* The logic in AQ module is different to the one in EnvironmentTelemetryModule. In Env module, if any sensor fails to getMetrics, no valid flag for the module. This prevents other sensors to report data.
* Fix pending clock change in PMSA003
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Make sure clock is always set to needed value
* Fix returns
* Fix trunk
* Fix on condition in reclock
* Fix trunk
* Add check on polling interval of sen5x
* Add missing serializer
---------
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 084796920179e80a7500d36c25fd4d82b3ef4214.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Fix trunk
* Fix on condition in reclock
* Add check on polling interval of sen5x
---------
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Added support for the new SSD1306 control panel.
* Added QMC6310N inspection to I2C scanner
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Initial commit of combined BLE and WiFi OTA
* Incorporate ota_hash in AdminMessage protobuf
* OTA protobuf changes
* Trunk fmt
---------
Co-authored-by: Jake-B <jake-b@users.noreply.github.com>
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
* remove duplicate HAS_LP5562 introduced by #6422
* add ST7796
* changes to get display centered+lib update
* seperated from tbeam
* forgot the simple scan case
* lowered speeds to 1/4
* added SPI Speed to constructor+ cleaned up variant.h
* even slower speeds....
* add ST7796
* changes to get display centered+lib update
* seperated from tbeam
* forgot the simple scan case
* lowered speeds to 1/4
* added SPI Speed to constructor+ cleaned up variant.h
* even slower speeds....
* changed variant name to tbeam-displayshield
* modified variant.h and merged ini file+testing on lower spi frequency for the lora module, display shield pumps out EMI?
* try higher speeds + HSPI
* cleanup of redundant code
* refelct changes?
* trunk fmt
* testing touchscreen code
* further testing
* changed to sensorlib 0.3.1
* i broke it , dont know how to fix at the moment will investigate
* add -1 functionality for touch IRQ
* revert to working example?
* it works.... is pressed was not working properly
* working touchscreen but gestures not moving display
* swap XY+ mirror X
* cleanup + addition of defines for on screen keyboard and canned message module
* removed debug lines, disabled bluetooth for now because of stack smashing protect failure
* reverted the revert #6640 + increased speed, bleutooth is stable now on reconnection cold booth etc , GPS is still not working though
* remove debug + add fixed baudrate for gps
* fmt
* revert NIMble
* changed display library to meshtastic org
* removed baudrate of 115200 and some commented out code
* Correct spelling
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Typo
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* display speed x10
* resolve conflicts
* undo
* revert speed increase CPU
* add SCREEN_TRANSITION_FRAMERATE 5
* spi speed increase of the display
* using the original touchscreen implementation
* removal of H file line
* add USE_ST7796 to missing places
* removed is pressed + interrupt
* revert changes of settings.json
* update to screen.cpp
* test identification of CST226 and CST328
* Update src/configuration.h
typo
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* made changes to detection because it was completely wrong, CST226SE has 2 posible adresses
* add merge queue
* try vars
* kerning in yaml.
* update comment
* lint etc
* touching to check grandfathering
* explicit ignores
* add WIP for Unit C6L (#7433)
* add WIP for Unit C6L
* adapt to new config structure
* Add c6l BLE and screen support (#7991)
* Minor c6l fix
* Move out of PRIVATE_HW
---------
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <Xaositek@users.noreply.github.com>
Co-authored-by: Markus <Links2004@users.noreply.github.com>
* Update Adafruit BusIO to v1.17.3 (#8018)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Update actions/checkout action to v5 (#8020)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Update actions/setup-python action to v6 (#8023)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Upgrade trunk (#8025)
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
* Update actions/download-artifact action to v5 (#8021)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix init for InputEvent (#8015)
* Automated version bumps (#8028)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Allow Left / Right Events for selection and improve encoder responsives (#8016)
* Allow Left / Right Events for selection and improve encoder responsives
* add define for ROTARY_DELAY
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* (resubmission) Manual GitHub actions to allow building one target or arch (#7997)
* Reset the modified files
* Fix some changes
* Fix some changes
* Trunk. That is all.
---------
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
* BaseUI Show/Hide Frame Functionality (#7382)
* Rename System Frame (from Memory) in code base
* Create menu options to Show/Hide frames: Node Lists, Bearings, Position, LoRa, Clock and Favorites frames
* Move Region Picker into submenu
* Tweak wording for Send Position vs Node Info if the device has GPS
* Update actions/checkout action to v5 (#8031)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Update actions/download-artifact action to v5 (#8032)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Update actions/setup-python action to v6 (#8033)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Phone GPS display on Position Screen for BaseUI (#7875)
* Phone GPS display on Position Screen
This is a PR to show when a phone shares GPS location with the node so you can reliably know what coordinate is being shared with the Mesh.
* Merge pull request #8004 from compumike/compumike/debug-heap-add-free-heap-debugging-to-all-log-lines
When `DEBUG_HEAP` is defined, add free heap bytes to every log line in `RedirectablePrint::log_to_serial`
* Feature: Seamless Cross-Preset Communication via UDP Multicast Bridging (#7753)
* Added compatibility between nodes on different Presets through `Mesh via UDP`
* Optimize multicast handling and channel mapping
- FloodingRouter: remove redundant UDP-encrypted rebroadcast suppression.
- Router: guard multicast fallback with HAS_UDP_MULTICAST and map fallback-decoded packets
to the local default channel via isDefaultChannel()
- UdpMulticastHandler: set transport_mechanism only after successful decode
* trunk fmt
* Move setting transport mechanism.
---------
Co-authored-by: GUVWAF <thijs@havinga.eu>
* Auto-favorite remote admin node
* Merge pull request #7873 from compumike/compumike/client-base-role
Add `CLIENT_BASE` role: `ROUTER` for favorites, `CLIENT` otherwise (for attic/roof nodes!)
* Fixes
* BaseUI Updates (#7787)
* Account for low resolution wide screen OLEDs
* Allow picking of Device Role and new Display Formatter for Device Role
* Add remainder of client roles to display formatter
* Don't update the role unless you pick a value
* Mascots are fun
* Fix warnings during compile time
* Improve some menus
* Mascots need to work everywhere
* Update Chirpy image
* Fix Trunk
* Update protobufs
* Add date to Clock screen
* Analog clocks love dates too
* Finalize date moves for analog clock
* Added Last Coordinate counter to Position screen (#7865)
Adding a counter to show the last time a GPS coordinate was detected to ensure the user is aware how long since the coordinate updated or to identify any errors.
* Fix
* Portduino config refactor (#7796)
* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
* updated shebang to use a more standard path for bash (#7922)
Signed-off-by: Trenton VanderWert <trenton.vanderwert@gmail.com>
* Show GPS Date properly in drawCommonHeader (#7887)
* Commit good code that is sustainable
* Fix new build errors
* BaseUI Updates (#7787)
* Account for low resolution wide screen OLEDs
* Allow picking of Device Role and new Display Formatter for Device Role
* Add remainder of client roles to display formatter
* Don't update the role unless you pick a value
* Mascots are fun
* Fix warnings during compile time
* Improve some menus
* Mascots need to work everywhere
* Update Chirpy image
* Fix Trunk
* Update protobufs
* Add date to Clock screen
* Analog clocks love dates too
* Finalize date moves for analog clock
* Add formatting and menu picking for other GPS format options (#7974)
* Add back options for other GPS format options
* Rename variables and don't overlap elements
* Fix default value
* Should probably add a menu while I'm here!
* Shorten names just a bit to fit on screens
* Fix off by one
* Labels try to make things better
* Missed a label
* Update protobufs (#8038)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Add formatting and menu picking for other GPS format options (#7974)
* Add back options for other GPS format options
* Rename variables and don't overlap elements
* Fix default value
* Should probably add a menu while I'm here!
* Shorten names just a bit to fit on screens
* Fix off by one
* Labels try to make things better
* Missed a label
* Add a new GPS model CM121. (#7852)
* Add a new GPS model CM121.
* Add CM121 to Unicore.
* Trunk fixes, remove unneded NMEA lines
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* (resubmission) Manual GitHub actions to allow building one target or arch (#7997)
* Reset the modified files
* Fix some changes
* Fix some changes
* Trunk. That is all.
---------
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
* PPA: Enable Ubuntu 25.10 (questing) (#7940)
* Update Protobuf usage, add MLS, fix clock (#8041)
* Update protobufs (#8045)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Fix icon
* C6l fixes (#8047)
* fix build with HAS_TELEMETRY 0 (#8051)
* Make sure to ACK ACKs/replies if next-hop routing is used (#8052)
* Make sure to ACK ACKs/replies if next-hop routing is used
To stop their retransmissions; hop limit of 0 is enough
* Update src/mesh/ReliableRouter.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* move HTTP contentTypes to Flash - saves 768 Bytes of RAM (#8055)
* Use `lora.use_preset` config to get name (#8057)
* Update RadioLib to v7.3.0 (#8065)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix Rotary Encoder Button (#8001)
this fixes the Rotary Encoder Button, currenlty its not working at all.
Currently the action `ROTARY_ACTION_PRESSED` is only triggerd with a IRQ on RISING, which results in nothing since the function detects the "not longer" pressed button --> no action.
the `ROTARY_ACTION_PRESSED` implementation needs to be called on both edges (on press and release of the button)
changing the interupt setting to `CHANGE` fixes the problem.
* Add another seeed_xiao_nrf52840_kit build environment for I2C pinout (#8036)
* Update platformio.ini
* Remove some more extraneous lines
* Add heltec_v4 board. (#7845)
* add heltec_v4 board.
* Update variants/esp32s3/heltec_v4/platformio.ini
Co-authored-by: Austin <vidplace7@gmail.com>
* Limit the maximum output power.
* Trunk fixes
Fixes formatting to match meshtastic trunk linter.
* Apply suggestion from @Copilot
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Apply suggestion from @Copilot
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Upgrade trunk (#8078)
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
* portduino bump to fix gpiod bug (#8083)
An earlier portduino causes problems with initializing gpiod lines. This pulls in the fix.
* Handle ext. notification module things even if not enabled (#8089)
* tlora-pager wake on button, and kb backlight toggling (#8090)
* Try-fix: Unstick that PhoneAPI state (#8091)
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Also pull a deviceID from esp32c6 devices (#8092)
* Remove line from BLE pin screen, to make pin readible on tiny screens
* Fix build errors (#8067)
* Heltec V4 is 16mb
* Clear lasttoradio on BLE disconnect (#8095)
* On disconnect, clear the lastToRadio buffer
* Move it, bucko!
* Revert "Fix build errors (#8067)"
This reverts commit d998f70b56.
* Automated version bumps (#8100)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Upgrade trunk (#8094)
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
* Update Adafruit BusIO to v1.17.4 (#8098)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Add three expansion screens for heltec mesh solar. (#7995)
* Add three expansion screens for heltec mesh solar.
* delete whitespace
Update variants/nrf52840/heltec_mesh_solar/variant.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* delete whitespace
Update variants/nrf52840/heltec_mesh_solar/platformio.ini
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Trunk
---------
Signed-off-by: Trenton VanderWert <trenton.vanderwert@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Dane Evans <dane@goneepic.com>
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <Xaositek@users.noreply.github.com>
Co-authored-by: Markus <Links2004@users.noreply.github.com>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
Co-authored-by: Markus <974709+Links2004@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: Tom <116762865+NomDeTom@users.noreply.github.com>
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
Co-authored-by: Michael <michael.overhorst@gmail.com>
Co-authored-by: GUVWAF <thijs@havinga.eu>
Co-authored-by: Trent V. <trenton.vanderwert@gmail.com>
Co-authored-by: Quency-D <55523105+Quency-D@users.noreply.github.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: GUVWAF <78759985+GUVWAF@users.noreply.github.com>
Thomas Göttgens
oscgonfer
Alexander BalyaandGitHub
lewisxheandBen Meadors
WillyJL
Heath Dutton🕴️andGitHub
JorropoandGitHub
vidplace7
Markus
Tom
Jason P
HarukiToreda
Michael
GUVWAF
Trent V.
GUVWAF