* stm32wl: add hardware RTC support infrastructure
Wires the STM32WL chip's internal RTC (running off the LSE 32.768kHz
crystal) into meshtastic's existing time-of-day framework
(perhapsSetRTC()/readFromRTC()), following the same pattern already
used for I2C RTC chips (RV3028, PCF8563/85063, RX8130CE).
LSE is started and polled manually before ever calling into the
STM32RTC library, with our own bounded timeout - the library's own
internal LSE startup path has no bounded fallback and hangs forever
via Error_Handler() if the crystal never locks, so this is required
for a board with a missing/faulty crystal to boot normally rather
than hang.
Gated behind a new HAS_LSE variant flag (currently unset everywhere,
so this is inert until a variant opts in - see follow-up commit).
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* gps: qualify RTC.h includes to avoid case-insensitive filesystem collision with STM32RTC
The stm32duino STM32RTC library (added to lib_deps in a follow-up
commit) ships its own src/rtc.h. On case-insensitive filesystems
(the macOS default), an unqualified #include "RTC.h"/<RTC.h> from
any file outside src/gps/ resolves to the library's rtc.h instead of
src/gps/RTC.h, since PlatformIO's LDF puts lib_deps include paths
ahead of the project's own -Isrc/gps.
Qualify every include as gps/RTC.h so it can't collide with any
same-named header a future dependency might ship, regardless of
filesystem case sensitivity. Purely mechanical, no behavior change.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl(rak3172): enable hardware RTC support
Opts rak3172 into the HAS_LSE infrastructure added previously: sets
STM32WL_LSE_DRIVE to a conservative default and pulls in the
STM32RTC library. rak3172 has ~63KB flash headroom going in;
build-verified at 76.7% flash usage after this change (up from a
73.8% baseline), well within budget.
wio-e5 is not opted in here despite sharing the same STM32WLE5 chip
- it's already at 96.8% flash usage today (GPS + I2C sensor support
compiled in, unlike rak3172), leaving too little headroom to safely
add STM32RTC without first trimming something else.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: add docstrings for LSE/RTC setup functions
Addresses CodeRabbit's docstring coverage check on PR #10961.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
* stm32wl: address CodeRabbit nitpicks on PR #10961
- Brace the single-statement HAS_LSE branch in perhapsSetRTC() to
match the sibling readFromRTC() branch's style.
- Quote the RTC.h include in PhoneAPI.cpp for consistency with every
other qualified include site.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add define for screen I2C frequency
* Add functions to get I2C screen frequency and port
* Make reclock function aware of screen-set I2C speeds
* Refurbish ReClockI2C API
* Make ReClockI2C API class
* Use new API in AirQualityTelemetry module
* Minor changes on some logs
* Update esp8266-oled library
* Fix esp8266 library
* Minor logging changes
* Improve setClock and restoreClock cases
* Make getter functions const, fix capitalisaiton of new functions
* Minor typo, remove pragma once
* Low prio debug fixes
* Mark getter functions as const (properly)
* Fix LOG based on coderabbit feedback
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Seeed Tracker X1 Support
* silence CPPCheck
* fix macro order regression and adapt stm32hal for new radiolib
* STM32 is a radiolib upstream fix ( https://github.com/jgromes/RadioLib/issues/1825 )
* fix STM32 regression
* Seeed Tracker X1 Support
* silence CPPCheck
* fix macro order regression and adapt stm32hal for new radiolib
* STM32 is a radiolib upstream fix ( https://github.com/jgromes/RadioLib/issues/1825 )
* fix STM32 regression
* address copilot OCD
* Split behavior only when the two LEDs are on distinct pins.
* bring naming in line with the other seeed devices
* update env name to fit convention too
* guarantee evaluation order
* Guard sensor readings against null values, make sensor use less power
* dependency swap - INA3221Sensor
update INA3221 initialization and measurement methods for compatibility with Rob Tillaart's library
Co-authored-by: Copilot <copilot@github.com>
* Addresses copilot review
Co-authored-by: Copilot <copilot@github.com>
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Refine comments on USB detection and INA3221
Updated comments regarding USB detection and INA3221 usage.
* Fix static_assert conditions for INA3221 channel definitions
Co-authored-by: Copilot <copilot@github.com>
* moved macro defines earlier to allow better use.
Co-authored-by: Copilot <copilot@github.com>
* Add raw register read methods for bus voltage and shunt current in INA3221Sensor
Co-authored-by: Copilot <copilot@github.com>
---------
Co-authored-by: Copilot <copilot@github.com>
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Consolidate SHTs into one class
* Remove separate SHT imports
* Create one single SHTXX sensor type
* Let the SHTXXSensor class handle variant detection
* Minor logging improvements
* Add functions to set accuracy on SHT3X and SHT4X
* Fix variable init in constructor
* Add bus to SHT sensor init
* Update src/modules/Telemetry/Sensor/SHTXXSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/Telemetry/Sensor/SHTXXSensor.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix accuracy conditions on SHTXX
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Merge upstream
* Add SHT2X detection on 0x40
* Read second part of SHT2X serial number
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
P0.04 is a digital power-enable pin for the NTC/LUX sensors, not an ADC
input. The old code was calling analogRead() on a floating GPIO that
happened to read ~mid-rail, coincidentally producing reasonable
temperature values.
- Rename T1000X_VCC_PIN to T1000X_SENSOR_EN_PIN and drive it HIGH in
initVariant() for both T1000-E and T1000-S variants
- Read BATTERY_PIN (with ADC_MULTIPLIER) instead, clamped to the 3.0V
LDO output (NTC_REF_VCC) for the NTC resistance calculation
* BSEC2 Replacement
- add approximation for IAQ to non-BSEC2 platforms.
- Re-add this sensor to ESP32 targets, and refactor env_extra includes.
- Fix C++ 11 compatibility
* Check for gas resistance 0
* Merge develop into SCD30
* Add SCD30 class
* Fix logging and admin commands
* Minor cleanup and logging improvements
* Minor formatting issue
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Improvements on setTemperature
* Fix casting float-uint16_t
* Pass 100 for resetting temperature offset
* Fix issues pointed out by copilot
* Add quick reboot to set interval quicker on scd30
* Change saveState to only happen after boot and minor log changes
* Fix missing semicolon in one shot mode log
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* simplify the observer pattern, since all the called functions are const getters.
* use arduino macro over std: for numerical values and refactor local variables in drawScrollbar()
* oh, so Cppcheck actually complained about const pointers not being const.
* slowly getting out of ifdef hell
* fix inkHUD warnings as well
* last 2 check warnings
* git checks should fail on low defects from now on
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Initial implementation for SFA30Sensor
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Add functional SCD4X
* Fix screen frame for CO2
* Add admin commands to SCD4X class
* Add further admin commands and fixes.
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 084796920179e80a7500d36c25fd4d82b3ef4214.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Small reordering in PMS class for consistency
* If one sensor fails, AQ telemetry still reports data
* Small formatting fix
* Add SEN5X to AQI in ScanI2C
* SCD4X now part of AQ module with template list
* Fixes difference between idle and sleep
* In LowPower, sleep is disabled
* Requires testing for I2C clock comms for commands
* Remove unnecessary import
* Add co2 to serialized AQ metrics
* Add SFA30 with new sensor template in AQ module
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Fix uninitMemberVars
* Fix import error for SCD4X
* Fix I2CClock logic
* Fix not reclocking back to 700000Hz
* Fix multiple sensors being read simultaneously
* The logic in AQ module is different to the one in EnvironmentTelemetryModule. In Env module, if any sensor fails to getMetrics, no valid flag for the module. This prevents other sensors to report data.
* Fix pending clock change in PMSA003
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Make sure clock is always set to needed value
* Fix returns
* Fix trunk
* Fix on condition in reclock
* Fix trunk
* Final SFA30 class implementation
* Add HCHO to screen and improve logs
* Add metrics to mesh packet serializer
* Minor fixes in logs
* OCD tidy up of logs
* Fix sleep function
* Remove old I2C_CLOCK_SPEED code
---------
Co-authored-by: nikl <nikl174@mailbox.org>
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Add functional SCD4X
* Fix screen frame for CO2
* Add admin commands to SCD4X class
* Add further admin commands and fixes.
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 084796920179e80a7500d36c25fd4d82b3ef4214.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Small reordering in PMS class for consistency
* If one sensor fails, AQ telemetry still reports data
* Small formatting fix
* Add SEN5X to AQI in ScanI2C
* SCD4X now part of AQ module with template list
* Fixes difference between idle and sleep
* In LowPower, sleep is disabled
* Requires testing for I2C clock comms for commands
* Remove unnecessary import
* Add co2 to serialized AQ metrics
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Fix uninitMemberVars
* Fix import error for SCD4X
* Fix I2CClock logic
* Fix not reclocking back to 700000Hz
* Fix multiple sensors being read simultaneously
* The logic in AQ module is different to the one in EnvironmentTelemetryModule. In Env module, if any sensor fails to getMetrics, no valid flag for the module. This prevents other sensors to report data.
* Fix pending clock change in PMSA003
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Make sure clock is always set to needed value
* Fix returns
* Fix trunk
* Fix on condition in reclock
* Fix trunk
* Add check on polling interval of sen5x
* Add missing serializer
---------
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Move PMSA003I to separate class and update AQ telemetry
* AirQualityTelemetry module not depend on PM sensor presence
* Remove commented line
* Fixes on PMS class
* Add missing warmup period to wakeUp function
* Fixes on compilation for different variants
* Add functions to check for I2C bus speed and set it
* Add ScreenFonts.h
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
* PMSA003I 1st round test
* Fix I2C scan speed
* Fix minor issues and bring back I2C SPEED def
* Remove PMSA003I library as its no longer needed
* Remove unused I2C speed functions and cleanup
* Cleanup of SEN5X specific code added from switching branches
* Remove SCAN_I2C_CLOCK_SPEED block as its not needed
* Remove associated functions for setting I2C speed
* Unify build epoch to add flag in platformio-custom.py (#7917)
* Unify build_epoch replacement logic in platformio-custom
* Missed one
* Fix build error in rak_wismesh_tap_v2 (#7905)
In the logs was:
"No screen resolution defined in build_flags. Please define DISPLAY_SIZE."
set according to similar devices.
* Put guards in place around debug heap operations (#7955)
* Put guards in place around debug heap operations
* Add macros to clean up code
* Add pointer as well
* Cleanup
* Fix memory leak in NextHopRouter: always free packet copy when removing from pending
* Formatting
* Only queue 2 client notification
* Merge pull request #7965 from compumike/compumike/fix-nrf52-bluetooth-memory-leak
Fix memory leak in `NRF52Bluetooth`: allocate `BluetoothStatus` on stack, not heap
* Merge pull request #7964 from compumike/compumike/fix-nimble-bluetooth-memory-leak
Fix memory leak in `NimbleBluetooth`: allocate `BluetoothStatus` on stack, not heap
* Update protobufs (#7973)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* Trunk
* Trunk
* Static memory pool allocation (#7966)
* Static memory pool
* Initializer
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
---------
Co-authored-by: WillyJL <me@willyjl.dev>
* Portduino dynamic alloc
* Missed
* Drop the limit
* Update meshtastic-esp8266-oled-ssd1306 digest to 0cbc26b (#7977)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix json report crashes on esp32 (#7978)
* Tweak maximums
* Fix DRAM overflow on old esp32 targets
* Guard bad time warning logs using GPS_DEBUG (#7897)
In 2.7.7 / 2.7.8 we introduced some new checks for time accuracy.
In combination, these result in a spamming of the logs when a bad time is found
When the GPS is active, we're calling the GPS thread every 0.2secs.
So this log could be printed 4,500 times in a no-lock scenario :)
Reserve this experience for developers using GPS_DEBUG.
Fixes https://github.com/meshtastic/firmware/issues/7896
* Scale probe buffer size based on current baud rate (#7975)
* Scale probe buffer size based on current baud rate
* Throttle bad time validation logging and fix time comparison logic
* Remove comment
* Missed the other instances
* Copy pasta
* Fix GPS gm_mktime memory leak (#7981)
* Fix overflow of time value (#7984)
* Fix overflow of time value
* Revert "Fix overflow of time value"
This reverts commit 084796920179e80a7500d36c25fd4d82b3ef4214.
* That got boogered up
* Remove PMSA003 include from modules
* Add flag to exclude air quality module
* Rework PMSA003I to align with new I2C scanner
* Reworks AQ telemetry to match new dynamic allocation method
* Adds VBLE_I2C_CLOCK_SPEED build flag for sensors with different I2C speed requirements
* Reworks PMSA003I
* Move add sensor template to separate file
* Split telemetry on screen options
* Add variable I2C clock compile flag
* Added to Seeed Xiao S3 as demo
* Fix drawFrame in AQ module
* Module settings override to i2cScan module function
* Move to CAN_RECLOCK_I2C per architecture
* Add reclock function in TelemetrySensor.cpp
* Add flag in ESP32 common
* Minor fix
* Move I2C reclock function to src/detect
* Fix uninitMemberVar errors and compile issue
* Make sleep, wakeUp functions generic
* Fix STM32 builds
* Add exclude AQ sensor to builds that have environmental sensor excludes
* Add includes to AddI2CSensorTemplate.h
* SEN5X first pass
* WIP Sen5X functions
* Further (non-working) progress in SEN5X
* WIP Sen5X functions
* Changes on SEN5X library - removing pm_env as well
* Small cleanup of SEN5X sensors
* Minor change for SEN5X detection
* Remove dup code
* Enable PM sensor before sending telemetry.
This enables the PM sensor for a predefined period to allow for warmup.
Once telemetry is sent, the sensor shuts down again.
* Small cleanups in SEN5X sensor
* Add dynamic measurement interval for SEN5X
* Only disable SEN5X if enough time after reading.
* Idle for SEN5X on communication error
* Cleanup of logs and remove unnecessary delays
* Small TODO
* Settle on uint16_t for SEN5X PM data
* Make AQTelemetry sensors non-exclusive
* Implementation of cleaning in FS prefs and cleanup
* Remove unnecessary LOGS
* Add cleaning date storage in FS
* Report non-cumulative PN
* Bring back detection code for SEN5X after branch rebase
* Add placeholder for admin message
* Add VOC measurements and persistence (WIP)
* Adds VOC measurements and state
* Still not working on VOC Index persistence
* Should it stay in continuous mode?
* Add one-shot mode config flag to SEN5X
* Add nan checks on sensor data from SEN5X
* Working implementation on VOCState
* Adds initial timer for SEN55 to not sleep if VOCstate is not stable (1h)
* Adds conditions for stability and sensor state
* Fixes on VOC state and mode swtiching
* Adds a new RHT/Gas only mode, with 3600s stabilization time
* Fixes the VOCState buffer mismatch
* Fixes SEN50/54/55 model mistake
* Adapt SEN5X to new sensor list structure. Improve reclock.
* Improve reClockI2C conditions for different variants
* Add sleep, wakeUp, pendingForReady, hasSleep functions to PM sensors to save battery
* Add SEN5X
* Fix merge errors
* Update library dependencies in platformio.ini
* Fix unitialized variables in SEN5X constructor
* Fix missing import
* Cleanup of SEN5X class
* Exclude AQ sensor from wio-e5 due to flash limitations
* Fix I2C clock change logic
* Fix trunk
* Fix on condition in reclock
* Add check on polling interval of sen5x
---------
Co-authored-by: Hannes Fuchs <hannes.fuchs+git@0xef.de>
Co-authored-by: Nashui-Yan <yannashui10@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Mike Robbins <mrobbins@alum.mit.edu>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* better logic to check if the RAK12035 soil sensor is calibrated, better log messaging if either of the default values were used.
* .
* changes to how default calibration is done and a message it the default calibration is used pointing to the actual calibration sketch so the user can find it and use it to improve accuracy.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* asked claude to fix the gps power rail issue when the io slot is in use.. this fixes the gps when both the RAK12500 GPS module and the RAK12035 soil sensor modules are being used.
* remove do { ... } while(0) from RESTORE_3V3_POWER() Macro
* remove some comments
* cleaner macro
* removed more excessive comments
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Initial commit of combined BLE and WiFi OTA
* Incorporate ota_hash in AdminMessage protobuf
* OTA protobuf changes
* Trunk fmt
---------
Co-authored-by: Jake-B <jake-b@users.noreply.github.com>
I thought git would be smart enough to understand all the whitespace changes but even with all the flags I know to make it ignore theses it still blows up if there are identical changes on both sides.
I have a solution but it require creating a new commit at the merge base for each conflicting PR and merging it into develop.
I don't think blowing up all PRs is worth for now, maybe if we can coordinate this for V3 let's say.
This reverts commit 0d11331d18.
* regenerate protobuf with bh1750 TelemetrySensorType
* Added wollewald/BH1750_WE@^1.1.10 dependecy
* Added support for BH1750 during i2C detection
* Create new BH1750Sensor and added in EnvironmentTelemetry
* clean code
* Attempt to fix protobuf include
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* rework I2C sensor init
the goal is to only instantiate sensors that are pressend to save memory.
side effacts:
- easyer sensor integration (less C&P code)
- nodeTelemetrySensorsMap can be removed when all devices are migrated
* add missing ifdef
* refactor a bunch of more sensors
RAM -816
Flash -916
* fix build for t1000
* refactor more sensors
RAM -192
Flash -60
* improve error handling
Flash -112
* fix build
* fix build
* fix IndicatorSensor
* fix tracker-t1000-e build
not sure what magic is used but it works
* Apply suggestion from @Copilot
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Apply suggestion from @Copilot
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Apply suggestion from @Copilot
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/Telemetry/Sensor/DFRobotGravitySensor.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update platformio inis for stm32 platform and wio-e5 variant for enabling i2c
* Don't reference timezone functions if MESHTASTIC_EXCLUDE_TZ is defined
* Use custom pow_of_two in RadioInterface instead of floating-point pow()
* First pass: enable sensors for STM32wL
* Fix AirQualityTelemetryModule being created if the PM25AQI header is missing
* Link in power sensor libraries
* more ini tweaks
* Add =1 to EXCLUDE defines, fix indentation.
* Drop HAS_WIRE in ini, it's defined in architecture.h
* Fix build when power sensor libraries are missing
Make MAX sensor integration into Power.cpp optional based on its library header existing.
Also make NullSensor expose a voltage and current sensor, because Power calls directly into these for INA sensors.
This lets us remove all the deps for the STM32WL platform.
* Change default I2C for RAK3172 to be I2C1, not I2C2
* Respect the laws of mathematics (oops)
oscgonferandGitHub
Thomas Göttgens
oscgonfer
WesselandGitHub
WillyJL
Jonathan Bennett
JorropoandGitHub
Chloe BethelandGitHub