* Don't launch canned message when waking screen or silencing notification
* Add screen ifdefs
* Get the #if right
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* fix(MQTT): First MapReport does not get sent
Throttle::isWithinTimespanMs(last_report_to_map, map_publish_interval_msecs) is
used to maintain the map reporting interval, but because last_report_to_map has
an initial value of 0, the map report routine does not start until the system
millis() time has passed map_publish_interval_msecs.
Fix this by adding a check that last_report_to_map is not 0.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* feat(MQTT): Send MapReporting immediately upon location fix
Do not update last_report_to_map when Map Report is attempted without a valid
location, as this results in waiting up to an hour (or configured Map Report
interval).
That usually happens because most nodes do not keep GPS warm, so GPS usually
locks after the first attempt at Map Report.
This change also results in the log WARNing message getting spammed until a
location is obtained, so remove the message for now.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* feat(MQTT): Throttled warning when position is not available for MapReport
Signed-off-by: Andrew Yong <me@ndoo.sg>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Add transmit history for throttling that persists between reboots
* Fix RAK long press detection to prevent phantom shutdowns from floating pins
* Update test/test_transmit_history/test_main.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Test fixes and placeholder for content handler tests
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Change file name from BLEDfuScure.cpp to BLEDfuSecure.cpp. Fix filenames
in documentation.
Signed-off-by: Koko <github@kokosoftware.pl>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add GPIO_DETECT_PA portduino config, and support 13302 detection with it.
* Tweak PA detect gpio to use pinMapping
* minor yaml output fixes
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Align telemetry broadcast want_response behavior with traceroute
* Fixes
* Reduce side-effects by making the telemetry modules handle the ignorerequest
* Remove unnecessary ignoreRequest flag
* Try inheriting from MeshModule
* Add exclusion for sensor/router roles and add base telem module
* Implement 'agc' reset for SX126x chip family
There's no actual agc on SX126x chips but you can reset the analog
registers by doing a warm sleep & running calibration.
* Address PR comments & implement for LR11x0 too
* calibrate for configured frequency band
* Gate LR11X0_AGC_RESET
* Apply SX1262 register 0x8B5 patch for improved GC1109 RX sensitivity
Sets the LSB of undocumented SX1262 register 0x8B5 on Heltec V4 and
Wireless Tracker V2 boards with the GC1109 FEM. This patch was
recommended by Heltec/Semtech and tested in MeshCore PR #1398, where
it significantly reduced packet loss on the Heltec V4.
* Use higher level function
* Add .venv/ to .gitignore
* Reduce maximum concurrent HTTPS connections to save memory
* Add heap check and limit connections to prevent HTTPS connection related crashes
* Use Throttle::isWithinTimespanMs for overflow-safe heap warning throttle
* Update src/mesh/http/WebServer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Fix double-free heap corruption and parser leak in web server handlers
- Remove double-free in handleFsBrowseStatic, handleNodes, handleScanNetworks:
JSONValue(const JSONArray&) shallow-copies pointers, so delete value already
recursively frees all elements. The explicit cleanup loops were deleting the
same pointers a second time, corrupting the ESP32 heap allocator metadata.
This is the likely root cause of #8827 (SSL setup failures after uptime).
- Fix memory leak in handleFormUpload: two early-return paths were missing
delete parser.
- Remove unused global HTTPClient httpClient and its includes.
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Hold GC1109 PA_POWER and PA_EN during deep sleep for LNA RX wake
Use rtc_gpio_hold_en to latch PA_POWER (LDO) and PA_EN (CSD) HIGH
during deep sleep so the GC1109 LNA remains powered for wake-on-packet
RX. Previously these pins used weak pull-ups which could lose state.
On deep sleep wake, skip these pins in the blanket RTC hold release and
instead release them in SX126xInterface::init() after GPIO registers are
set HIGH first, avoiding a power glitch on the GC1109.
Trade-off: ~6.5mA additional deep sleep current for significantly
improved wake-on-packet RX sensitivity (~17dB).
Reference: https://github.com/meshcore-dev/MeshCore/pull/1600
* Add LDO startup delay before GC1109 chip enable
TLV75733P LDO has ~550us startup time (datasheet tSTR). On cold boot,
wait 1ms for VBAT to stabilise before driving CSD/CPS, per GC1109
power-on sequence requirement. On deep sleep wake the LDO is held on
via RTC latch so no delay is needed.
* onNavUp() sets the menu cursor to the last item if not shown
* skip headers when showing the menu cursor in onNavUp() and onNavDown()
* skip headers when showing the menu cursor in onButtonShortPress()
* brace cursor incrementing
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
Ben Meadors
Andrew YongandGitHub
Thomas GöttgensandGitHub
WesselandGitHub
WesselandGitHub
AustinandGitHub
oscgonferandGitHub
David RembaandGitHub
