isCharging()/getHasUSB() were hard-compiled to always return false on
this board: the nrfx_power_usbstatus_get() block in Power.cpp that
derives them is gated behind #ifdef NRF_APM, and this board's variant.h
never defined it - unlike tracker-t1000-e and wio-tracker-wm1110, which
do. Confirmed on hardware: before this change, `Battery: usbPower=0,
isCharging=0` regardless of actual USB/charge state; after, `usbPower=1,
isCharging=1` while genuinely on USB power with a battery attached.
Same underlying gap as #4367, fixed for tracker-t1000-e and
wio-tracker-wm1110 in #4376 (which also fixed a deeper bug where
PowerStatus notifications were gated behind a battery-level null check -
that part is already fixed generically in Power.cpp today, so this board
only needed the define). Looks like a simple oversight from when this
board was added, since it's newer than the two boards #4376 touched.
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Fix SENSOR power saving deep sleep behavior
Deep sleep could be entered while a telemetry packet was still queued
or on air, truncating the transmission. canSleep() gained a deepSleep
parameter and now vetoes in that case; light sleep is unchanged.
Telemetry modules defer a pending deep sleep (bounded to 30s) until the
radio is idle and no longer let the sensor polling interval override
the 5s pre-sleep grace period. A failed sensor read still arms deep
sleep instead of leaving the node awake for a full telemetry interval.
Fixes#10890Fixes#10932
* Deduplicate telemetry deep sleep deferral logic
Move the radio-busy deferral and its counter into BaseTelemetryModule
and add an isPowerSavingSensor() helper. Removes the telemetry-specific
counter from OSThread. The sleep arming block stays per module because
it needs protected OSThread members not visible to the base class.
* size gate: emit flash_bytes from ELF for targets without a packaged .bin
nRF52 builds package hex/uf2/DFU zip but no raw .bin, so collect_sizes.py
dropped budgeted envs like rak4631 entirely and the size-budget-gate failed
closed. Emit ELF text+data as flash_bytes in the manifest and use it as the
fallback flash measurement.
* Factor shared size-tool invocation into run_size_tool helper
Position sharing was opt-out (the default primary channel shipped
position_precision=13) while device telemetry was already opt-in, and a
normal firmware upgrade preserves saved config, so existing nodes stayed
position-on. This makes both broadcasts opt-in, both on a fresh flash and via
a one-time migration for upgrading nodes.
- Fresh default: initDefaultChannel now sets position_precision=0.
- One-time migration in loadFromDisk, gated on a dedicated
POSITION_TELEMETRY_OPTIN_VER (26) watermark kept separate from
DEVICESTATE_CUR_VER (bumping that would re-run the NodeDatabase v24
legacy decoder on already-migrated v25 DBs): disables position broadcast
on PUBLIC/default-PSK channels and forces every device-telemetry
mesh-broadcast flag plus the MQTT map-report location off.
- Private-PSK channels are left untouched: a channel with a custom key is a
deliberate trusted-group setup, so its configured precision is preserved.
- Idempotent: ordinary saves never re-stamp .version, so a user who
re-enables sharing is not re-disabled on the next boot.
- Added pure channelFileUsesPublicKey() (operates on the raw ChannelFile,
since the channels singleton isn't initialized during loadFromDisk) and
refactored Channels::usesPublicKey() to delegate to it.
- New test/test_optin_migration native suite (14 cases).
Every other .cpp/.h pair in src/ (350 of 351) uses identical
capitalization between the two files. Power.cpp/power.h was the sole
outlier; this aligns it with the rest of the codebase. No functional
change — all includes already resolved this file the same way on
case-sensitive filesystems.
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add software LoRa IRQ polling and an MCP23017 expander HAL for radios behind an I2C expander
Some boards route the SX126x control lines (NRESET/DIO1/BUSY) through an I2C
GPIO expander instead of native GPIOs, and don't wire the expander's /INT to
the MCU, so RadioLib cannot take a hardware DIO1 interrupt.
Two reusable pieces, both gated behind USE_MCP23017 / LORA_DIO1_SOFTWARE_POLL
so builds that don't define them are unaffected:
- ExtensionIOMCP23017 + MCP23017LockingArduinoHal: a RadioLib HAL that maps
virtual pins (MCP23017_VPIN_BASE .. +15) onto an MCP23017's GPIO, so
RESET/BUSY/DIO1 reads and writes become I2C transactions while the real SPI
GPIOs (SCK/MOSI/MISO/CS) pass straight through. A failed I2C read skips the
read-modify-write rather than clobbering the rest of the bank.
- LORA_DIO1_SOFTWARE_POLL: with no DIO1 interrupt available, the SX126x
interface polls the radio IRQ status register from the radio thread and
synthesizes the ISR_TX/ISR_RX events, filtering noisy preamble/header IRQs so
they can't starve TX. A 1 ms ISR_POLL_TICK drives the poll; TX timers may
overwrite the pending tick (pollMissedIrqs() is the backup that bounds the
latency of the busy-Rx contention window). Behaviour is unchanged on all
boards that keep the hardware interrupt.
* Add Meshnology W10 AIOT Dev Kit variant (SX1262 via MCP23017 expander)
ESP32-S3R8 + EBYTE E22-900MM22S (SX1262) + AXP2101 PMIC + Quectel L76KB GPS +
SPI TFT, with the radio's RESET/DIO1/BUSY and the LCD reset routed through an
MCP23017 I2C expander at 0x20. The expander's /INT is not wired to the ESP32,
so DIO1 uses the software poll. Pins come from the board schematic and the
vendor firmware; the expander is an MCP23017 despite the V1.1 schematic's stale
'TCA9555' label (the V1.2 placement diagram and all vendor code use the MCP23017
register map).
A local pins_arduino.h shadows the generic esp32s3 variant to drop RGB_BUILTIN,
which otherwise pulls the Arduino RMT HAL into the link and fails against this
build's trimmed FreeRTOS config.
Reports HardwareModel 140 (MESHNOLOGY_W10, already present in the protobufs).
Hardware-verified on a real W10 AIOT Dev Kit: AXP2101 PMU, MCP23017, SX1262
init + a full over-the-air TX/RX round trip through the expander, PCF85063 RTC,
SHT41 and QMI8658 auto-detected, and an L76KB GPS fix.
* meshnology-w10: enable ES8311 speaker for notification tones
Bring up the ES8311 codec (I2C 0x18) -> NS4150 amp -> speaker so the board can
play notification tones / ringtones over the I2S buzzer path (the
use_i2s_as_buzzer external-notification option). Codec2 voice stays out of
scope: it is SX1280-only and this is a sub-GHz board.
- variant.h: HAS_I2S + DAC_I2S pins (MCLK=1, BCK=2, WS=4, DOUT=5, DIN=3)
- platformio.ini: arduino-audio-driver + ESP8266Audio + ESP8266SAM
- extra_variants/meshnology_w10/variant.cpp: lateInitVariant() configures the
ES8311, mirroring the other Meshtastic ES8311 boards. Kept codec-only (no
main.h) so the audio driver's 'using namespace audio_driver' does not pull a
conflicting GpioPin into scope alongside Meshtastic's class GpioPin.
- AudioThread.h: toggle the NS4150 amp (MCP23017 EXIO_PA_CTRL) around playback.
Verified on hardware: a test tune played audibly through the speaker.
* meshnology-w10: address review feedback on the MCP23017 driver
- ExtensionIOMCP23017: serialize register access with a mutex, since the radio
HAL (BUSY/DIO1/RESET) and AudioThread (amp enable) now reach the expander from
different threads and the read-modify-write paths are not atomic.
- digitalRead: return a fail-safe HIGH on a failed read instead of LOW, so a
transient I2C error on the LoRa BUSY line can't look like 'ready' and let
RadioLib start an SPI transaction early. (DIO1 is polled via the radio IRQ
register, not this pin.)
- enablePinChangeInterrupt: use the checked readReg() overload and skip on a
failed read, matching the other read-modify-write helpers.
- meshnology_w10 variant.cpp: log a warning if an ES8311 register write NACKs
instead of silently leaving the codec half-configured.
- RadioInterface.cpp: guard the MCP23017 HAL branch with ARCH_ESP32 to match the
include and driver-file guards.
* Replace board-model audio/sleep ifdefs with reusable variant capability macros
Two shared-code spots keyed off specific hardware models; move the board-specific
detail into opt-in macros the variants define, so the core code stays generic and
new boards can opt into the behavior class without touching shared files.
- AudioThread amp control: drop the T_LORA_PAGER / MESHNOLOGY_W10 ifdefs. A board
with an I2S amp now defines AUDIO_AMP_ENABLE(on) in its variant.h (T-LoRa Pager
and Meshnology W10 do), and AudioThread just calls it around playback. The
expander includes are keyed on USE_XL9555 / USE_MCP23017 (capabilities) instead
of the model name.
- Light-sleep / DIO1 wakeup: drop the SENSECAP_INDICATOR check. Boards whose
LORA_DIO1 is an expander pin (not an ESP32 GPIO) define LORA_DIO1_EXTENDED_IO
(SenseCAP Indicator and Meshnology W10), and sleep.cpp keys off that for both
the light-sleep skip and the DIO1 GPIO-wakeup skip. This also fixes a latent
issue on the SenseCAP: it previously reached the GPIO-wakeup path and called
gpio_pulldown_en() on a virtual expander pin; it now skips that cleanly.
Builds verified on meshnology_w10, tlora-pager, and seeed-sensecap-indicator.
* meshnology-w10: silence cppcheck constParameterPointer on the ISR-callback helper
isIsrTxCallback() takes a function pointer it only compares; cppcheck's
constParameterPointer wants it 'pointer to const', which is meaningless for a
function pointer (the codebase already globally suppresses the sibling
constParameterCallback). Inline-suppress it to keep the check green.
* HopScaling: qualify the member assignment as this->count
cppcheck (CI's version) flags 'count = newCount;' at the end of trimIfNeeded()
as uselessAssignmentArg ('assignment of function parameter has no effect') - a
false positive, since count is a member that outlives the call. Write it as
this->count (matching the Step-1 assignment above) so the analyzer sees a member
write. This finding comes in via the develop merge, not this board; fixing it
here to unblock the PR's cppcheck check.
* fix(power): check EXT_CHRG_DETECT with defined(), not truthiness
#elif EXT_CHRG_DETECT tests the macro's numeric value rather than
whether it's defined. Every existing board happens to assign it to a
nonzero pin, so this never misfired, but a board using pin 0 (e.g.
PA0 on STM32) would silently skip this branch even though the pin is
defined and configured.
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
Signed-off-by: Andrew Yong <me@ndoo.sg>
* fix(power): consider EXT_CHRG_DETECT in isVbusIn()
isVbusIn() used EXT_PWR_DETECT alone. On boards where that pin is a
charge-complete/standby signal rather than a continuous power-present
signal, isVbusIn() reports false for the entire duration of an active
charge. If EXT_CHRG_DETECT is also defined, OR it in: charging can
only happen when power is present, so this only adds correct true
results and is a no-op for boards where EXT_PWR_DETECT already means
"power present" continuously.
Assisted-by: Claude Sonnet 5 <noreply@anthropic.com>
Signed-off-by: Andrew Yong <me@ndoo.sg>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* CI: track RAM (.data+.bss) in size reports and gate on per-env budgets
The 2.8.0 nRF52840 heap regression (99% heap in field reports) shipped
invisibly because CI only tracked flash. On nRF52840 the heap arena is the
linker gap after .bss, so every byte of static .data+.bss growth shrinks the
usable heap 1:1 - RAM needs the same guardrails flash already has.
What's added:
- bin/platformio-custom.py emits ram_bytes (.data + .bss from the ELF, via
the toolchain size tool) into each .mt.json manifest. Heap/stack
placeholder sections are deliberately excluded.
- bin/collect_sizes.py records {flash_bytes, ram_bytes} per env;
bin/size_report.py grows RAM and RAM-delta columns in the PR size report.
Older artifacts without ram_bytes (and legacy int-schema baselines)
degrade to "n/a" instead of crashing.
- bin/ram_budgets.json: per-env RAM/flash budgets, enforced only for envs
listed there. Seeded with rak4631: ram 113,000 (current 110,948 + ~2 KB
slack), flash 786,000 (current 765,192 + ~20 KB; the app region is
0x27000..0xEA000 = 798,720 and the image must stay clear of the
warm-store ring guard in extra_scripts/nrf52_warm_region.py).
- New size-budget-gate CI job runs size_report.py --enforce-budgets and
fails the build on violation; the informational firmware-size-report job
now also renders budget usage into the PR comment.
- src/main.cpp: opt-in boot heap watermark (-DMESHTASTIC_HEAP_WATERMARK_CHECK)
logs LOG_ERROR when less than 20% of the heap is free at the end of
setup(). Off by default; skipped on platforms without heap accounting.
How budgets are raised: deliberately, never automatically. If a change needs
more headroom, bump the env's limit in bin/ram_budgets.json in the same PR
and justify the increase in the PR description.
Verified: python3 bin/test_size_scripts.py (23/23 pass, including ram_bytes
parsing, n/a fallback, and over/under/missing-env budget-gate cases).
* Address review: fail the budget gate closed, fix RAM section matching
- size-budget-gate workflow: drop continue-on-error on the manifest
download and the empty-dir fallback, so the job fails when the data it
gates on cannot be fetched.
- size_report.py --enforce-budgets now fails closed on every
missing-data path instead of trivially passing: empty collected sizes,
a budgeted env that was not built, or a manifest without the budgeted
metric. Report-only mode keeps rendering those as n/a.
- load_budgets() rejects zero/negative/non-integer budgets with a clear
error (a typo'd budget could previously crash budget_markdown with
ZeroDivisionError or silently skip the check); the percentage render
keeps a defensive guard for direct callers.
- compute_ram_bytes(): count RISC-V small-data sections (.sdata/.sbss)
and exclude ESP-IDF .rtc.* sections, which live outside the
heap-competing SRAM.
- Trim the heap-watermark comment in main.cpp to two lines.
bin/test_size_scripts.py: 27/27 - the two fail-open assertions are
flipped to fail-closed, with new report-only counterparts plus cases for
empty sizes under enforcement and malformed budgets.
* Right-size nRF52 heap tiers after 2.8.0 heap-exhaustion field reports
Field reports on 2.8.0 show nRF52840 devices at 99% heap (114/115 KB)
within minutes of boot; operator new asserts on OOM, so these devices
are one allocation from a reboot. The 2.8.0 cache sizing ladders gave
nRF52 the largest non-PSRAM tiers on the assumption that a BLE-only
part has a roomy heap - the arena is actually ~125 KB shared with the
FreeRTOS task stacks.
Per-target retiers (nRF52840 unless noted):
- Traffic Management cache 1000 -> 250 entries (10 KB -> 2.5 KB); the
unclassified fallthrough drops 1000 -> 400 to match the classic-ESP32
tier (also affects RP2040/RP2350)
- Warm node store 200 -> 100 entries (8 KB -> 4 KB); the non-XXAA
fallthrough drops 320 -> 100 so an unclassified RAM-constrained part
can't boot-allocate 12.8 KB
- MESSAGE_HISTORY_LIMIT 20 -> 10 (text pool 4.4 KB -> 2.2 KB), the tier
classic ESP32 already ships
- MAX_RX_TOPHONE 32 -> 16, shrinking the static packet pool 70 -> 54
slots (~6.6 KB of .bss returned to the heap arena)
- PacketHistory hash index off arch-wide (1 KB); O(n) over 240 records
is negligible at LoRa packet rates
- OLEDDISPLAY_REDUCE_MEMORY arch-wide (~1 KB OLED back buffer); the five
TFT variants -U it because TFTDisplay.cpp needs buffer_back for
dirty-window diffing
- Drop the stale "for testing" 1024-entry TMM override on T1000-E
Measured on rak4631: heap arena grows 124,572 -> 131,180 B and boot
allocations drop ~15.7 KB, roughly +22 KB free heap on the field-report
device class.
Migration: the nRF52840 warm flash ring replays through place() (LRU),
so the newest 100 identities survive the shrink; the file backend
rejects oversized snapshots cleanly (new test covers this). Native
suites pass (536/536 Docker, 13/13 native-macos warm store); rak4631,
heltec-mesh-node-t114 (TFT) and tracker-t1000-e build green.
* Add central memory-class ladder (MemClass.h) with fail-safe-small defaults
The 2.8.0 nRF52840 heap exhaustion happened because each RAM-sized cache
picked its per-platform tier from its own chip #ifdef ladder, and every
ladder's fallthrough default was its largest non-PSRAM tier - nRF52 was
never named, so it silently got 1000-entry caches on a ~115 KB arena.
This introduces src/memory/MemClass.h: a single MESHTASTIC_MEM_CLASS
(TINY / SMALL / MEDIUM / LARGE) ranked by usable app heap after platform
overheads, with the deliberate property that an unclassified chip lands
in SMALL - a new target boots with small caches until someone opts it up
in one visible place.
The TMM cache, warm store, MAX_RX_TOPHONE and MAX_SATELLITE_NODES
ladders in mesh-pb-constants.h now key off the class; branches pinned by
something other than RAM stay explicit and say why (nRF52840's SoftDevice
arena, RP2040's warm.dat watchdog bound). MAX_NUM_NODES intentionally
stays separate - it is flash-shaped (nodes.proto vs LittleFS), not
heap-shaped.
A per-class MESHTASTIC_BOOT_CACHE_BUDGET static_assert now covers the
three big boot-allocated caches, so the next cache-adding PR that would
blow a small platform's budget fails to compile instead of exhausting
heap in the field.
No values change for any existing target: rak4631, tbeam, rak11310 and
wio-e5 build byte-identical before/after; all ladders remain
#ifndef-guarded so variant overrides keep working.
* Address review: fix RP2350 class-table doc, add PacketRecord static_assert
- MemClass.h's class table claimed RP2350 was MEDIUM while the mapping
ladder classifies it SMALL (with RP2040) - the table now matches the
ladder, with a note that RP2350 is a MEDIUM candidate whenever someone
wants to tune it up (kept SMALL here so this header stays a behavioral
no-op).
- The boot-cache budget comment referenced a static_assert pinning
PacketHistory::PacketRecord at 20 B that did not exist (only a layout
comment). Add the real static_assert so the budget math in
mesh-pb-constants.h fails to compile if the record layout changes.
Also merges develop (the base #10898 landed there as a squash, which is
what made this stacked branch conflict); develop's mesh-pb-constants.h
is byte-identical to this branch's base, so the resolution keeps the
MemClass ladder unchanged. rak4631 and wio-e5 build green;
test_packet_history 47/47.
* Address review: share PACKETHISTORY_MAX, trim policy comments
- Hoist PACKETHISTORY_MAX from PacketHistory.cpp into
mesh-pb-constants.h (next to the MAX_NUM_NODES it derives from) so the
constructor clamp and the boot-cache budget static_assert use one
definition instead of hand-mirrored arithmetic that could drift. The
expression stays valid where MAX_NUM_NODES resolves at runtime
(ESP32-S3, portduino); the pointless 2.0 double math becomes integer.
- Trim the MemClass.h header (36 -> 16 comment lines) and the budget /
sizing-policy comments per the repo comment-length guideline, keeping
the class table, the fail-safe-small rule, the override mechanism, and
the include-order constraint.
rak4631 (compile-time MAX_NUM_NODES) and heltec-v3 (runtime) build
green; test_packet_history 47/47.
The app RAM ORIGIN in both nrf52840 linker scripts has been a hard-coded
0x20006000 (24 KB reserved for S140) since they were introduced, but
sd_ble_enable() with our fixed Bluefruit configuration (one peripheral
link, BANDWIDTH_MAX / ATT MTU 247, 0x1000 attribute table) requires
substantially less. The SoftDevice cannot use the gap and the app image
is linked above it, so every byte between the true requirement and the
ORIGIN is simply unusable RAM - on a part where 2.8.0 field reports
showed the heap arena at 99% use.
Lower the ORIGIN to 0x20004000 in both s140 v6 and v7 scripts. The heap
arena is the linker gap on this platform, so the change is worth exactly
+8,192 B of free heap on every nRF52840 board (verified: rak4631 .heap
section 124,572 -> 132,764 B; both v6- and v7-script boards link with
.data at 0x20004000).
Safety net: Bluefruit.begin()'s return value - previously discarded -
is now checked. If a future SoftDevice or Bluefruit config change raises
the requirement past the reservation, the node logs a critical error
instead of silently running without BLE, with instructions to re-measure
via CFG_DEBUG=1 ("SoftDevice's RAM requires: 0x...").
* first pass tests
* more tests
* Fix two crafted-admin-packet crashes found by the E5 fuzzer
Both are reachable from an authorized admin (local from==0, admin channel,
or PKC) - remote DoS:
1. SIGFPE in LoRa config validation. A set_config LoRaConfig with
use_preset=false and bandwidth=0 makes freqSlotWidth 0, so numFreqSlots
is 0 and `hash(name) % numFreqSlots` (RadioInterface.cpp) divides by
zero. Guard the modulo; the existing channel_num check then rejects/
clamps the config.
2. Stack overflow in Channels::getKey. A SECONDARY channel at the primary
slot with an empty PSK recursed into getKey(primaryIndex) forever. Skip
the primary-key borrow when chIndex == primaryIndex.
Re-enable the E5 admin fuzzer to hit both triggers again (use_preset both
ways incl. bandwidth 0, plus the set_channel tag) as regression guards.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
* Correct fuzz-test invariants after the crash fixes
- E5 admin fuzz: node eviction under a filling NodeDB is legitimate, so
assert only the bounded-count invariant, not that a specific seed node
survives 6000 mutating ops.
- TMM blitz: scope off the nodeinfo direct-response send path (it needs a
fully-wired MeshService/phone queue the fixture doesn't provide; the
deterministic directResponse tests cover it). The crafted-nodenum
rate/unknown/position cache stress is unchanged.
clod helped too
* realistic tests
* test: dedup fuzz RNG into shared test/support/DeterministicRng.h
The four in-tree fuzz suites (test_fuzz_decode, test_fuzz_packets,
test_hop_scaling, test_traffic_management) each carried a byte-identical
copy of the seeded 64-bit LCG (rngSeed/rngNext/rngByte/rngRange). Hoist
it into one shared header so there is a single generator to reason about
and no risk of the copies drifting. static inline keeps per-suite state
per translation unit and avoids -Wunused-function for suites that don't
use every helper. Also corrects a stale comment in test_traffic_management
(the blitz's nodeinfo direct-response path is intentionally left off).
No behavioral change: same constants, same per-suite seeds.
clod helped too
* test: fuzz uncovered ProtobufModule handlers and the MQTT downlink ingress
Extend the in-tree fuzz coverage to packet sources that previously had
none:
- test_fuzz_packets E8/E9/E10: drive PositionModule, DeviceTelemetryModule
and NeighborInfoModule at handleReceivedProtobuf directly (via using-shims,
bypassing the ProtobufModule reply/send path so no router is needed). The
fixture already stands up nodeDB/service/channels, and nodeStatus/powerStatus
are auto-initialized in main.cpp, so no new globals are required. Adds a
shared fuzzRxHeader() helper for crafting adversarial RX packet headers.
- test_fuzz_decode: add meshtastic_KeyVerification to the decode table. The
KeyVerification and StoreForward handler paths are documented as decode-level
only, with the concrete reason each is intrinsic (private-state gating /
PSRAM + self-pointer wiring), not a fixture gap.
- test_mqtt: test_receiveFuzzServiceEnvelope blitzes the non-RF broker-push
ingress (onReceiveProto) two ways - raw garbage bytes that must fail envelope
decode cleanly, and a well-formed ServiceEnvelope wrapping a crafted inner
MeshPacket over crafted channel_id/gateway_id - exercising the channel match,
isFromUs, XEdDSA receive policy and perhapsDecode chain. Adds a deliverRaw()
passthrough to MQTTUnitTest.
All under the coverage env (ASan/LSan). No firmware/src changes. Full sweep
GREEN 27/27, 544 cases.
clod helped too
* Harden LoRa/channel config against crafted admin messages; consolidate test helpers
Production (review findings on the hot-fuzz crash fixes):
- Clamp bandwidth at the source (clampBandwidthKHz) in checkOrClampConfigLora
and applyModemConfig so numFreqSlots can never be 0 for any consumer; a
bandwidth-0 set_config previously passed validation and re-armed the SIGFPE
on the next applyModemConfig.
- Guard applyModemConfig's hash % numFreqSlots (the validator's sibling modulo
was fixed earlier but this one was still unguarded).
- Enforce the primary-channel invariant in Channels::onConfigChanged: a config
demoting every slot now re-promotes the stale SECONDARY slot (keeping its
key) or restores the default channel if the slot is DISABLED, instead of
leaving every getPrimaryIndex() reader on a non-primary slot. The getKey
recursion guard stays as defense-in-depth.
Tests:
- New test/support/MockMeshService.h and AdminModuleTestShim.h replace four
byte-identical mocks and three divergent admin shims (test_mqtt's capturing
mock is genuinely different and stays).
- DeterministicRng.h: add rngFill() (replaces 14 hand-rolled fill loops) and
rngEdgeNodeNum() (unifies the three NodeNum boundary pools).
- Extract fuzzChannelSettings() shared by the set_channel case and fuzzBeacon.
- fuzzBeacon: the un-terminated branch now fills the whole buffer with non-NUL
bytes so the strnlen bound is actually stressed (~50% of iterations, not ~4%).
- E6 beacon fuzz: replace the TEST_ASSERT_TRUE(true) tautology with real
invariants (handler never consumes; offers land in lastReceivedOffer keyed
to the sender).
- Trim the seven over-long comment blocks flagged against the 1-2 line rule;
the FINDINGS trailer moves to this commit message (see production notes).
Full native suite GREEN 27/27 under the coverage (ASan/LSan) env.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
* Clamp UTF-8 char length in the emote walkers; add test_fuzz_emotes
A TEXT_MESSAGE payload is opaque protobuf bytes, so PB_VALIDATE_UTF8 never
screens it - invalid UTF-8 and truncated multi-byte lead bytes reach the
emote/width render path verbatim. EmoteRenderer's walkers advanced by
utf8CharLen(lead) without clamping to the bytes actually remaining, so a
truncated lead (e.g. a lone 0xF0, which claims 4 bytes) near the end of the
buffer made getUtf8ChunkWidth's memcpy read past the string. ASan confirms a
heap-buffer-overflow READ from measureStringWithEmotes.
Add utf8CharLenClamped() and use it at every walk site (width measure,
truncation cut-loop, and the draw-path text-run/chunk builders); the one
already-guarded site (matchAtIgnoringModifiers) is unchanged.
New test/test_fuzz_emotes drives measureStringWithEmotes and truncateToWidth
over adversarial byte strings (biased to embed/end in truncated multi-byte
leads) in exact-sized heap buffers so any over-read is a hard ASan fault. Its
headless display uses a synthetic font (firstChar 0, fontData centered in a
large buffer) so the stock OLEDDisplay::getStringWidth - which indexes the
font jump table with a signed char and over-reads for any byte >= 0x80 - does
not mask the finding. native-suite-count bumped 27 -> 28.
Full native suite GREEN 28/28 under the coverage (ASan/LSan) env.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
* Keep emote width measurement in-bounds for non-ASCII bytes
OLEDDisplay::getStringWidth (the utf8=false path EmoteRenderer uses on default
builds) indexes the font jump table by (c - firstChar) with a signed char and
no bounds check, so any byte outside printable ASCII - high bytes from UTF-8
text, but also a stray control byte like 0x0A - reads outside the font array.
On-device this reads adjacent flash and returns a garbage width; under ASan the
test_fuzz_emotes fuzzer flags it as a global-buffer-overflow, and it made the
non-ASCII width measurement meaningless either way.
The OLED driver is a pinned upstream dependency, so guard it firmware-side in
EmoteRenderer's getStringWidth helper: measure a sanitized copy where any byte
outside [0x20, 0x7E] counts as a '?' placeholder. Printable ASCII is unchanged
and the UA/RU lookup path is untouched.
test_fuzz_emotes now drives a real ArialMT font instead of the synthetic
in-bounds font it needed before this fix, so the suite exercises the true
production width path (utf8CharLen clamp + this sanitizer) end to end. The same
fuzzer tripped the global-buffer-overflow before this change.
Full native suite GREEN 28/28 under the coverage (ASan/LSan) env.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
---------
Co-authored-by: Claude Fable 5 <noreply@anthropic.com>
* Add MemAudit: per-subsystem heap accounting in the boot log
The 2.8.0 nRF52840 heap-exhaustion field reports had to be diagnosed by
hand, reconstructing each subsystem's heap footprint from source and
build flags one report at a time. This makes every future report
self-diagnosing from the serial log: a tiny fixed-size registry
(src/memory/MemAudit.*) that big long-lived allocations report into,
printed as one line at the end of setup() and alongside the periodic
"Heap free:" log:
MemAudit[boot]: tmm=2500 warm=4000 pkthist=5824 nodedb=13440
msgstore=2200 pktpool(live)=3270 total=31234
Instrumented: NodeDB hot vector (nodedb) + satellite maps (satmaps,
rb-tree overhead estimated), WarmNodeStore (warm), PacketHistory records
and hash index (pkthist), TrafficManagement caches (tmm/tmm_ni),
MessageStore text pool (msgstore), TFT line/repaint buffers (display),
and live in-flight packets (pktpool(live)) via an optional audit tag on
the packet pool allocator - the one hot path, counted with a relaxed
32-bit atomic add (single instructions on Cortex-M, no locks).
Cost: 128 B RAM for the 16-tag table, well under 1 KB flash on rak4631.
MESHTASTIC_MEM_AUDIT=0 compiles it out to inline no-op stubs (call
sites need no ifdefs); STM32WL, the tightest flash target, defaults off.
New native suite test_mem_audit covers add/set/snapshot arithmetic, tag
reuse (pointer and cross-TU strcmp fallback), null/unknown tags, and
table-full behavior; test/native-suite-count bumped to 28.
* native-wasm: add src/memory/ to the curated source filter
The wasm env denies all sources and adds an explicit file list; MemAudit
callers (main, MeshService, NodeDB, PacketHistory) are in that list but
src/memory/MemAudit.cpp was not, so wasm-ld failed on undefined
memaudit:: symbols.
* Right-size nRF52 heap tiers after 2.8.0 heap-exhaustion field reports
Field reports on 2.8.0 show nRF52840 devices at 99% heap (114/115 KB)
within minutes of boot; operator new asserts on OOM, so these devices
are one allocation from a reboot. The 2.8.0 cache sizing ladders gave
nRF52 the largest non-PSRAM tiers on the assumption that a BLE-only
part has a roomy heap - the arena is actually ~125 KB shared with the
FreeRTOS task stacks.
Per-target retiers (nRF52840 unless noted):
- Traffic Management cache 1000 -> 250 entries (10 KB -> 2.5 KB); the
unclassified fallthrough drops 1000 -> 400 to match the classic-ESP32
tier (also affects RP2040/RP2350)
- Warm node store 200 -> 100 entries (8 KB -> 4 KB); the non-XXAA
fallthrough drops 320 -> 100 so an unclassified RAM-constrained part
can't boot-allocate 12.8 KB
- MESSAGE_HISTORY_LIMIT 20 -> 10 (text pool 4.4 KB -> 2.2 KB), the tier
classic ESP32 already ships
- MAX_RX_TOPHONE 32 -> 16, shrinking the static packet pool 70 -> 54
slots (~6.6 KB of .bss returned to the heap arena)
- PacketHistory hash index off arch-wide (1 KB); O(n) over 240 records
is negligible at LoRa packet rates
- OLEDDISPLAY_REDUCE_MEMORY arch-wide (~1 KB OLED back buffer); the five
TFT variants -U it because TFTDisplay.cpp needs buffer_back for
dirty-window diffing
- Drop the stale "for testing" 1024-entry TMM override on T1000-E
Measured on rak4631: heap arena grows 124,572 -> 131,180 B and boot
allocations drop ~15.7 KB, roughly +22 KB free heap on the field-report
device class.
Migration: the nRF52840 warm flash ring replays through place() (LRU),
so the newest 100 identities survive the shrink; the file backend
rejects oversized snapshots cleanly (new test covers this). Native
suites pass (536/536 Docker, 13/13 native-macos warm store); rak4631,
heltec-mesh-node-t114 (TFT) and tracker-t1000-e build green.
* Drop stale OLEDDISPLAY_REDUCE_MEMORY -U on t114 / mesh-solar-tft
Only USE_TFTDISPLAY variants (t1, t096, wismeshtap) compile
TFTDisplay.cpp and need the lib's buffer_back; t114 and mesh-solar-tft
render through the meshtastic-st7789 driver, which handles the
reduced-memory configuration fine - as #10894 (merged from develop)
already established by defining the flag there. Remove the -U guard and
the per-variant -D (redundant with the arch-wide define in nrf52_base
on this branch). Both variants verified building.
* nrf52_lto: fix variant LTO exclusion (match srcnode, not mirrored path) + post-link guard
The CI-fix follow-up in #10829 anchored _is_board_variant() to
<PROJECT_DIR>/variants/ using node.get_abspath() -- but build middleware
receives nodes from the SCons variant-dir mirror, whose abspath is
$BUILD_DIR/variants/.../variant.cpp. The anchor never matched, so the
variant silently went back into whole-image LTO: the shipped ELF has
initVariant() resolved to the core's weak empty stub (bare `bx lr`),
PIN_3V3_EN is never driven, and the SX1262 probe fails with
CHIP_NOT_FOUND again -- while the build stays green, because the
post-link guard only checked IRQ handlers.
Fix: match against node.srcnode().get_abspath(), which undoes the
variant-dir mirror (the same trick piobuild.py uses for middleware
pattern matching).
Add a second post-link guard so this failure mode is a red build, not a
field failure: the linked variant.cpp.o must contain no .gnu.lto_*
sections (proves the -fno-lto recompile fired), and any override the
object defines strong (initVariant) must resolve strong in the ELF.
Verified both ways on nrf52_promicro_diy_tcxo: clean build is green with
T _Z11initVariantv and a real initVariant body in the ELF; re-breaking
the matcher turns the build FAILED with both guard checks firing.
clod helped a lot
* address comments
* nrf52_lto: defer variant CCFLAGS so APP_VERSION is present
The variant -fno-lto recompile snapshotted projenv["CCFLAGS"] inside the
build middleware, which fires during $BUILD_SCRIPT. But -DAPP_VERSION... is
appended to projenv by bin/platformio-custom.py, an unprefixed extra_script
that PlatformIO runs as a POST script -- after the middleware. The frozen
override therefore lacked APP_VERSION, so recompiling any board variant whose
variant.cpp includes configuration.h (rak_wismeshtag via sleep.h,
seeed_xiao_nrf52840_kit, seeed_mesh_tracker_X1) failed with
'APP_VERSION must be set by the build environment'.
Defer the CCFLAGS read to a callable construction variable: SCons invokes it
during command substitution, after every SConscript (post-scripts included),
so projenv now carries the version flags. -fno-lto is appended last so it
still wins over the inherited -flto.
Verified clean builds of rak_wismeshtag, seeed_xiao_nrf52840_kit, and rak4631
(regression) -- all green with the variant guard reporting the board variant
kept out of LTO.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update LovyanGFX to v1.2.24
* Remove note on LovyanGFX version compatibility
Removed note about version v1.2.7 breaking display functionality.
---------
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
ScanI2CTwoWire is compiled out on builds that define
MESHTASTIC_EXCLUDE_I2C (e.g. native-wasm/portduino), while the
AirQuality module still builds there. Skip the re-scan when I2C is
excluded; there is nothing to scan.
* second pass adding beacons admin
* Bump protobufs submodule to merged MESHBEACON_CONFIG (PR #970)
clod helped.
* Gate MeshBeacon module config behind admin auth in PhoneAPI
The FromRadio module-config sync copied moduleConfig.mesh_beacon unconditionally. MeshBeaconConfig embeds two ChannelSettings (broadcast_offer_channel, broadcast_on_channel) that carry PSKs, so an unauthorized client could exfiltrate channel PSKs when MESHTASTIC_PHONEAPI_ACCESS_CONTROL is enabled - bypassing the redaction already applied to mqtt/network/security config.
Gate the payload copy on getAdminAuthorized(), mirroring the mqtt case; unauth clients now receive an empty MeshBeaconConfig.
clod helped
Audit and fuzzing of the RF-packet decode -> dispatch -> display/phone paths for
the "crash a node or phone with a crafted packet" surface, beyond the XEdDSA
authenticity work.
Crash fixes (reproduced under AddressSanitizer / UBSan):
- GeoCoord::latLongToUTM/latLongToMGRS read fixed letter tables out of bounds on
extreme latitude_i/longitude_i from a received Position, and narrowed
out-of-range easting/northing doubles to unsigned (float-cast-overflow UB).
Clamp the UTM zone, the easting/northing narrowing, and the band/col/row
indices. Regression: test_geocoord_extreme_coords_no_oob.
- EnvironmentTelemetry/AirQualityTelemetry render attacker floats via
String(float), which on nRF52/RP2040/STM32/portduino formats into a fixed
char[33] (dtostrf) and overflows near FLT_MAX. Clamp the rendered metrics via
UnitConversions::displaySafeFloat (finite + magnitude <= 1e9), unit-tested in
test_type_conversions.
Defense-in-depth + robustness:
- TraceRouteModule::printRoute: fix an snr_back[-1] OOB read (wrong count in the
guard) and stop formatting the INT8_MIN "unknown SNR" sentinel as a dB value.
- WaypointModule/NodeDB: sanitize untrusted strings before the OLED renderer and
the phone-facing ClientNotification (belt-and-suspenders vs PB_VALIDATE_UTF8).
- MeshService::sendToPhone: withhold NODEINFO/WAYPOINT packets whose nested string
won't cleanly decode, protecting strict phone protobuf decoders without
affecting mesh relay.
Tests: new test_fuzz_decode (protobuf decode + UTF-8 sanitizer fuzz) and
test_fuzz_packets (perhapsDecode / module-handler / traceroute / phone-gate fuzz),
all under AddressSanitizer; native-suite-count 25 -> 27. Full suite 515/515 green.
The Python MCP server + hardware test harness that lived under mcp-server/
now has its own home at https://github.com/meshtastic/meshtastic-mcp
(published, versioned independently). Remove the in-tree copy and wire the
firmware repo to the standalone server externally.
- Delete mcp-server/ (96 files) and the 8 harness-coupled AI workflow files
under .claude/commands/ and .github/prompts/ that drove ./mcp-server/
run-tests.sh — those workflows now ship with meshtastic-mcp as skills.
- .mcp.json: register the server via
`uvx --from git+https://github.com/meshtastic/meshtastic-mcp meshtastic-mcp`
instead of a local ./mcp-server/.venv, keeping MESHTASTIC_FIRMWARE_ROOT="."
so the MCP tools still work from this checkout with no local build.
- Repoint the remaining references (AGENTS.md, CLAUDE.md,
.github/copilot-instructions.md, bin/regen-*.sh, docs, Screen.h,
userPrefs.jsonc, test/fixtures/nodedb/README.md, .trunk/configs/.bandit)
at the standalone repo. The MCP tool surface is unchanged — only the
pytest harness moves out; run it from a meshtastic-mcp checkout with
MESHTASTIC_FIRMWARE_ROOT pointed here.
No build/CI/platformio coupling existed, so nothing in the firmware build
changes.
Co-authored-by: Claude Opus 4.8 <noreply@anthropic.com>
* Add define for screen I2C frequency
* Add functions to get I2C screen frequency and port
* Make reclock function aware of screen-set I2C speeds
* Refurbish ReClockI2C API
* Make ReClockI2C API class
* Use new API in AirQualityTelemetry module
* Minor changes on some logs
* Update esp8266-oled library
* Fix esp8266 library
* Minor logging changes
* Improve setClock and restoreClock cases
* Make getter functions const, fix capitalisaiton of new functions
* Minor typo, remove pragma once
* Low prio debug fixes
* Mark getter functions as const (properly)
* Fix LOG based on coderabbit feedback
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Audit of the XEdDSA packet-signing implementation (#10478) surfaced several
issues in when unsigned packets are accepted on receive or emitted on send.
This fixes them and adds regression coverage.
- Unicast NodeInfo exchange no longer breaks against signer nodes: the
NodeInfoModule downgrade drop is gated to broadcasts, since senders never
sign unicast (want_response replies, directed exchanges).
- Replace the payload-size sign heuristic with an exact encoded-size gate
(signedDataFits) and mirror it on the receive side, removing a dead band
where 167-168 B broadcasts were signed then failed TOO_LARGE.
- Extract the receive policy into checkXeddsaReceivePolicy() and apply it to
plaintext-MQTT decoded downlink, which previously skipped signature
verification and downgrade protection entirely.
- Reject signatures whose length is neither 0 nor 64 as malformed, so a
crafted partial signature can't inflate the size estimate and dodge the
unsigned-downgrade drop.
- Hold cryptLock on the MQTT verify path (shared Ed25519 key cache).
- Clear any client-preset signature on packets we originate, on all builds.
- Randomized (hedged) signing per the Signal XEdDSA spec: bump the
meshtastic/Crypto pin to the build where XEdDSA::sign mixes 32 bytes of
caller randomness into the nonce as Z (meshtastic/Crypto#3), and seed those
bytes in xeddsa_sign from HardwareRNG (checked, with a seeded-CSPRNG
fallback). test_crypto pins that repeated signs differ and both verify.
Adds test coverage: test_packet_signing groups A-E (receive matrix, send
policy, NodeInfo backstop, encoding invariants, decoded-ingress policy),
test_mqtt end-to-end downlink cases, and a test_crypto randomization check.
Ben Meadors
Andrew YongandGitHub
Ian McEwenandGitHub
ManuelandGitHub
Thomas GöttgensandGitHub
AustinandGitHub
HarukiToredaandGitHub
Jonathan BennettandGitHub
Benjamin FaershteinandGitHub
oscgonferandGitHub
lasek0andGitHub
Jason PandGitHub