* Add T-Beam BPF (144-148 Mhz LoRa)
* minor correction to fix compiler warnings
* Add T-Beam BPF (144-148 Mhz LoRa)
* minor correction to fix compiler warnings
* Add ITU regions for this device and make GPS work.
* Switch pin after defining it as output
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Lora CS is indeed 1, SD Card CS is 10
* Include the back option.
* Fix compilation with pioarduino (USB_MODE)
* Default ham to narrow_fast
* Default PROFILE_HAM to slot 17
This is an appropriate default in the USA but not the EU.
The slot override really should follow the region itself, not the regionprofile.
* Fix for ITU 2/3 split
* Add ITU region options to MenuAction enum
* Add HAS_HAM_2M definition to variant headers for 2M support
* Re-add PROFILE_HAM regionprofile
Accidentally removed in last merge
* Trunk fmt
* Initial default slots
* Switch to TinyFast
Still need to flesh out the default channels
* Adjust slotOverrides for TinyFast
* RadioLib doesn't accept 15.625 kHz
Use 15.6 instead
* Set RF95 pins for T-Beam Supreme
May cause regressions!!
* Remove other-variant changes (BPF-only)
These have been moved to other PRs
* Remove mismatch guarding (we need a more comprehensive approach)
* Add comment back
* Add template for PA curve
* This is a 5-6W radio!! Add TX_GAIN_LORA
* Trunk fmt because NomDeTom hates emdashes
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Add Meshnology W12 (WiFi LoRa 32 V5) variant with LR2021 radio
ESP32-S3R8 + 16 MB flash + Semtech LR2021 dual-band LoRa + SSD1315 OLED,
Heltec V3-style pinout.
Pin map comes from the vendor pin sheet and vendor Arduino demos, confirmed
on hardware: I2C scan finds the OLED at 0x3C on SDA17/SCL18, and the LR2021
answers on NSS=8 SCK=9 MISO=11 MOSI=10 with BUSY=13/NRESET=12 verified by
reset-pulse probing.
The IRQ line needs LR2021_IRQ_DIO_NUM 8. RadioLib defaults irqDioNum to 5,
but DIO5 is not bonded out on this board - the two IRQ lines are DIO7 -> IO7
and DIO8 -> IO14, established by driving each radio DIO as a GPIO output and
watching which ESP32 pin followed. Left at the default, every interrupt is
routed to a floating pin: RX/TX still appear to work because
RadioLibInterface::pollMissedIrqs() falls back to polling the IRQ status
register, but the blocking scanChannel() waits on the pin itself and never
returns.
A shadow pins_arduino.h is needed because the generic esp32s3 one defines
RGB_BUILTIN, which pulls the Arduino RMT HAL into the link and fails against
this build's FreeRTOS config.
* Address review: add W12 variant metadata, trim comments
Declares the custom_meshtastic_* metadata the build manifest expects. Without
it the emitted .mt.json carried no hwModel, slug, display name or support
level, so the board was invisible to the flasher - and board_level = extra
kept it out of PR builds entirely, which is why it never appeared in this
PR's board list. It now matches the W10 sibling at board_level = pr with
support level 1. hwModel stays 255/PRIVATE_HW until a W12 enum lands in the
protobufs.
Also trims the header comments to the one-or-two-line limit in AGENTS.md;
the vendor pin sheet and probing evidence live in the PR description.
- t5s3-epaper: the board's 3.3V octal (AP_3v3) PSRAM is unreliable at the qio_opi
default of 80MHz (Total PSRAM reads 0, display dead / boot-loop); clock it at 40MHz.
- EInkParallelDisplay: skip EInk init and no-op display ops when the PSRAM framebuffer
is unavailable, so the node boots headless instead of hard-faulting on a NULL buffer.
- src/platform/esp32: weak software __atomic_*_{1,2,4} so esp32s3 links on toolchains
(e.g. macOS) that lack the sized libcalls GCC emits under -mdisable-hardware-atomics.
* Build fix
* update
* Update platformio.ini
* Update SerialConsole.cpp
* Remove Network provisioning for this build
* Update platformio.ini
Per Vid, this is not needed once his PR is merged
* fix: resolve merge conflict in SerialConsole.cpp - use setHostDraining(false) from develop
---------
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
* Snake!
* Add spiLock to snake score saving
* Check fixes
* More careful locking
* WIP: Big Display Node
* Update src/graphics/HUB75Display.cpp
Co-authored-by: coderabbitai[bot] <136622811+coderabbitai[bot]@users.noreply.github.com>
* Add HUB75 Native
* Add Tetris game module with core logic and UI integration
- Implement TetrisGame class for game logic, including piece movement, rotation, and line clearing.
- Create TetrisModule class to manage game state, input handling, and rendering on OLED display.
- Introduce high score tracking with persistence and optional mesh broadcasting.
- Define UI states for title, playing, paused, game over, and high scores.
- Implement input handling for game controls and state transitions.
- Add rendering functions for the game board, high scores, and title screen.
* feat(snake): add snake graphics and update display logic in SnakeModule
* Prompt for Initials for Tetris, too
* refactor games module
* Games refactor
* hub75 native double buffer
* Games tuning
* Make joystick repeat events on held button
* Add clouds and colors
* Fix breakout and more color
* difficulty tuning
* trunk
* refactor game announcements, etc
* Scale chirpy gravity as game speed increases
* Portduino, check for hub75 display before reading in hub75 options
* Final(?) games tuning
* Potential fix for pull request finding
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* Properly ignore input when games screen not shown
* Fail gracefully when HUB75 is selected but not supported.
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: coderabbitai[bot] <136622811+coderabbitai[bot]@users.noreply.github.com>
Co-authored-by: Ixitxachitl <kramerfm@gmail.com>
Co-authored-by: Copilot Autofix powered by AI <175728472+Copilot@users.noreply.github.com>
* fix(device-install): flash littlefs at the offset from firmware metadata
device-install.sh read the spiffs offset out of the .mt.json metadata into
SPIFFS_OFFSET, but flashed the littlefs image at $OFFSET -- a separate
variable still holding the hardcoded 0x300000 default. The metadata value
was never used, so any board with a non-default partition table had its
filesystem written to the wrong place.
Unify on SPIFFS_OFFSET, and guard both metadata overrides so a table that
omits ota_1 or spiffs falls back to the built-in default instead of handing
esptool an empty offset. Quote both offsets at the call site: the spiffs one
is newly consumed from jq, and a multi-line result would otherwise word-split
into esptool's argv and silently mis-pair address with file.
device-install.bat already does all of this correctly; this brings the shell
script to parity.
* fix(tlora-t3s3): give the 4MB T3-S3 boards an app partition that fits
tlora-t3s3-v1 and tlora-t3s3-epaper have overflowed the shared 4MB
partition-table.csv app slot (ota_0 = 0x250000 = 2,424,832 bytes) on every
develop build since 22072c5f4 (2026-06-20). The last green build,
ca7d82629, cleared it by 881 bytes; develop is now ~38.7KB over. These envs
have no board_level, so they only build in the full matrix on push to
develop -- which is why no PR ever caught it.
Add partition-table-t3s3.csv, dedicated to the 4MB ESP32-S3FH4R2 T3-S3
boards, and point all three t3s3 envs at it:
app ota_0 0x010000 0x290000 (was 0x250000, +256KB)
flashApp ota_1 0x2A0000 0x0A0000 (unchanged size)
spiffs 0x340000 0x0C0000 (was 0x100000, -256KB)
The headroom comes out of spiffs, not flashApp: the unified BLE OTA image is
636,544 bytes against a 655,360 byte slot, so ota_1 has nothing to give. The
table is contiguous, ends exactly on the 4MB boundary, keeps both app
partitions 64KB-aligned, and leaves the littlefs image these boards ship well
inside the remaining 768KB.
Verified with a Docker build of all three envs:
tlora-t3s3-v1 2,463,504 91.7%
tlora-t3s3-epaper 2,458,487 91.5%
tlora-t3s3-epaper-inkhud 2,400,851 89.4%
Trimming was considered and rejected. The entire emoji set is 6,304 bytes
(measured A/B build), and cutting traffic management plus the paxcounter,
storeforward, rangetest and atak modules recovers 46,636 -- enough to land at
99.7% full, i.e. weeks of headroom at develop's observed growth rate, in
exchange for shipping a feature-reduced board. The slot was simply mis-sized
for a board this full.
Note this changes flash layout: existing T3-S3 units must be erased and
factory-flashed once to pick up the new offsets. They already cannot run a
current develop build, so no working configuration regresses.
* Add software LoRa IRQ polling and an MCP23017 expander HAL for radios behind an I2C expander
Some boards route the SX126x control lines (NRESET/DIO1/BUSY) through an I2C
GPIO expander instead of native GPIOs, and don't wire the expander's /INT to
the MCU, so RadioLib cannot take a hardware DIO1 interrupt.
Two reusable pieces, both gated behind USE_MCP23017 / LORA_DIO1_SOFTWARE_POLL
so builds that don't define them are unaffected:
- ExtensionIOMCP23017 + MCP23017LockingArduinoHal: a RadioLib HAL that maps
virtual pins (MCP23017_VPIN_BASE .. +15) onto an MCP23017's GPIO, so
RESET/BUSY/DIO1 reads and writes become I2C transactions while the real SPI
GPIOs (SCK/MOSI/MISO/CS) pass straight through. A failed I2C read skips the
read-modify-write rather than clobbering the rest of the bank.
- LORA_DIO1_SOFTWARE_POLL: with no DIO1 interrupt available, the SX126x
interface polls the radio IRQ status register from the radio thread and
synthesizes the ISR_TX/ISR_RX events, filtering noisy preamble/header IRQs so
they can't starve TX. A 1 ms ISR_POLL_TICK drives the poll; TX timers may
overwrite the pending tick (pollMissedIrqs() is the backup that bounds the
latency of the busy-Rx contention window). Behaviour is unchanged on all
boards that keep the hardware interrupt.
* Add Meshnology W10 AIOT Dev Kit variant (SX1262 via MCP23017 expander)
ESP32-S3R8 + EBYTE E22-900MM22S (SX1262) + AXP2101 PMIC + Quectel L76KB GPS +
SPI TFT, with the radio's RESET/DIO1/BUSY and the LCD reset routed through an
MCP23017 I2C expander at 0x20. The expander's /INT is not wired to the ESP32,
so DIO1 uses the software poll. Pins come from the board schematic and the
vendor firmware; the expander is an MCP23017 despite the V1.1 schematic's stale
'TCA9555' label (the V1.2 placement diagram and all vendor code use the MCP23017
register map).
A local pins_arduino.h shadows the generic esp32s3 variant to drop RGB_BUILTIN,
which otherwise pulls the Arduino RMT HAL into the link and fails against this
build's trimmed FreeRTOS config.
Reports HardwareModel 140 (MESHNOLOGY_W10, already present in the protobufs).
Hardware-verified on a real W10 AIOT Dev Kit: AXP2101 PMU, MCP23017, SX1262
init + a full over-the-air TX/RX round trip through the expander, PCF85063 RTC,
SHT41 and QMI8658 auto-detected, and an L76KB GPS fix.
* meshnology-w10: enable ES8311 speaker for notification tones
Bring up the ES8311 codec (I2C 0x18) -> NS4150 amp -> speaker so the board can
play notification tones / ringtones over the I2S buzzer path (the
use_i2s_as_buzzer external-notification option). Codec2 voice stays out of
scope: it is SX1280-only and this is a sub-GHz board.
- variant.h: HAS_I2S + DAC_I2S pins (MCLK=1, BCK=2, WS=4, DOUT=5, DIN=3)
- platformio.ini: arduino-audio-driver + ESP8266Audio + ESP8266SAM
- extra_variants/meshnology_w10/variant.cpp: lateInitVariant() configures the
ES8311, mirroring the other Meshtastic ES8311 boards. Kept codec-only (no
main.h) so the audio driver's 'using namespace audio_driver' does not pull a
conflicting GpioPin into scope alongside Meshtastic's class GpioPin.
- AudioThread.h: toggle the NS4150 amp (MCP23017 EXIO_PA_CTRL) around playback.
Verified on hardware: a test tune played audibly through the speaker.
* meshnology-w10: address review feedback on the MCP23017 driver
- ExtensionIOMCP23017: serialize register access with a mutex, since the radio
HAL (BUSY/DIO1/RESET) and AudioThread (amp enable) now reach the expander from
different threads and the read-modify-write paths are not atomic.
- digitalRead: return a fail-safe HIGH on a failed read instead of LOW, so a
transient I2C error on the LoRa BUSY line can't look like 'ready' and let
RadioLib start an SPI transaction early. (DIO1 is polled via the radio IRQ
register, not this pin.)
- enablePinChangeInterrupt: use the checked readReg() overload and skip on a
failed read, matching the other read-modify-write helpers.
- meshnology_w10 variant.cpp: log a warning if an ES8311 register write NACKs
instead of silently leaving the codec half-configured.
- RadioInterface.cpp: guard the MCP23017 HAL branch with ARCH_ESP32 to match the
include and driver-file guards.
* Replace board-model audio/sleep ifdefs with reusable variant capability macros
Two shared-code spots keyed off specific hardware models; move the board-specific
detail into opt-in macros the variants define, so the core code stays generic and
new boards can opt into the behavior class without touching shared files.
- AudioThread amp control: drop the T_LORA_PAGER / MESHNOLOGY_W10 ifdefs. A board
with an I2S amp now defines AUDIO_AMP_ENABLE(on) in its variant.h (T-LoRa Pager
and Meshnology W10 do), and AudioThread just calls it around playback. The
expander includes are keyed on USE_XL9555 / USE_MCP23017 (capabilities) instead
of the model name.
- Light-sleep / DIO1 wakeup: drop the SENSECAP_INDICATOR check. Boards whose
LORA_DIO1 is an expander pin (not an ESP32 GPIO) define LORA_DIO1_EXTENDED_IO
(SenseCAP Indicator and Meshnology W10), and sleep.cpp keys off that for both
the light-sleep skip and the DIO1 GPIO-wakeup skip. This also fixes a latent
issue on the SenseCAP: it previously reached the GPIO-wakeup path and called
gpio_pulldown_en() on a virtual expander pin; it now skips that cleanly.
Builds verified on meshnology_w10, tlora-pager, and seeed-sensecap-indicator.
* meshnology-w10: silence cppcheck constParameterPointer on the ISR-callback helper
isIsrTxCallback() takes a function pointer it only compares; cppcheck's
constParameterPointer wants it 'pointer to const', which is meaningless for a
function pointer (the codebase already globally suppresses the sibling
constParameterCallback). Inline-suppress it to keep the check green.
* HopScaling: qualify the member assignment as this->count
cppcheck (CI's version) flags 'count = newCount;' at the end of trimIfNeeded()
as uselessAssignmentArg ('assignment of function parameter has no effect') - a
false positive, since count is a member that outlives the call. Write it as
this->count (matching the Step-1 assignment above) so the analyzer sees a member
write. This finding comes in via the develop merge, not this board; fixing it
here to unblock the PR's cppcheck check.
* Update LovyanGFX to v1.2.24
* Remove note on LovyanGFX version compatibility
Removed note about version v1.2.7 breaking display functionality.
---------
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
Adds the Traffic Management module (TMM) plus the NodeDB/warm-store and
next-hop foundations it builds on:
- Unified per-node cache (flat array, 8-bit relative ticks) shared by all
features; role-aware throttles for tracker / lost-and-found.
- Position deduplication: drop unchanged position rebroadcasts within a
configurable interval; precision driven off the channel ceiling (clamped to
the public-key max on well-known channels). Enabled by default at 11h.
- Per-node rate limiting and unknown-packet filtering (config-driven; a
non-zero companion field enables each feature -- no bool toggles).
- NodeInfo direct response from cache with role-based hop clamps.
- Persistent next-hop overflow store: confirmed hops have no TTL, are seeded
from NodeInfoLite at boot, and survive hot-store eviction.
- Three-tier sender-role resolution (hot NodeInfoLite -> warm store -> TMM
cache). Role is cached write-time (seeded on first track, refreshed from
NodeInfo), pins its cache entry like a next-hop hint, and is evicted last.
- Warm store caches device role + protected category across reboot/eviction.
- PositionModule stationary floor for tracker / lost-and-found.
- PSRAM gating for warm/satellite/TMM cache sizes; STM32WL excluded.
Protobufs: TrafficManagementConfig trimmed to the five uint32 fields actually
used; submodule repointed to protobufs develop.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
* fix(esp32): skip RTC timer wake on user shutdown
Do not arm esp_sleep_enable_timer_wakeup when msecToWake is portMAX_DELAY (UI shutdown), matching nRF52 system_off semantics.
fix(rak_wismesh_tap_v2): Tag OCV curve and 16MB partition
Add OCV_ARRAY matching WisMesh Tag for accurate SOC. Use 16MB flash partition scheme for TAP V2 hardware.
Co-authored-by: Cursor <cursoragent@cursor.com>
* Trunkt
---------
Co-authored-by: Cursor <cursoragent@cursor.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Wipe message Store on factory reset
* Check for destination 0 in a new message, and convert to broadcast
* Make sure CHARGE_LED_state gets turned off, to avoid stuck LEDs
* Take the spiLock in MessageStore when clearing messages
* Trunk
* Add thinknode M5 voltage curve
* Fix the oops
* fix(t5s3-epaper): increase ED047TC1 margins to 16px on all sides
Tested on device — 16px uniform margins look noticeably cleaner than
the previous asymmetric 8–9px values. Canvas shrinks from 944×523 to
928×508 (H_OFFSET_BYTES=2, V_OFFSET_TOP/BOTTOM=16).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* fix(t5s3-epaper): remove EINK_EDGE_LINES calibration diagnostic from ED047TC1
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
* fix(t5s3-epaper): align TOUCH_THRESHOLD_X with TOUCH_THRESHOLD_Y (40px)
X axis threshold was 60 while Y was 40, causing asymmetric swipe detection.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
---------
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* rename variant and add guard macros
* older G3 operational. M7 next.
* Split out G3 and M7 to different variants. Completely new PCB design. The G3 stays on 'PRIVATE_HW'
* Define button behaviour and use all of the device flash
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: caveman99 <25002+caveman99@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* ThinkNode G3, ETH support WIP
* rename variant and add guard macros
* older G3 operational. M7 next.
* Split out G3 and M7 to different variants. Completely new PCB design. The G3 stays on 'PRIVATE_HW'
* Define button behaviour and use all of the device flash
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: copilot-swe-agent[bot] <198982749+Copilot@users.noreply.github.com>
Co-authored-by: caveman99 <25002+caveman99@users.noreply.github.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* True Colors on TFT (Heltec Mesh Node T114, Heltec Vision Master T190, CardPuter Adv, T-Deck, T-Lora Pager)
* Theme support - New and some Classic Themes!
* Colored Compass
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Fixes issues with #includes inherited from `configuration.h` when building for pioarduino.
Aligns t5s3_epaper with other variants like t_deck_pro.
Co-authored-by: Copilot <copilot@github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* PMU interrupt pin defined in t-watch s3
* Implement button control on T-Watch S3
Added interrupt handling for the Power/Corona button on T-Watch S3, I use it to control screen state.
* Reducing labels
* Reducing labels
* Updated the comment
* ISR is now IRAM-safe
Updated interrupt management not to cause random crashes.
* Trunk
* Simplify and use INPUT_BROKER_CANCEL
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Ben MeadorsandGitHub
ManuelandGitHub
TomandGitHub
